Instructions / Assembly

ManualsBrandsCustom Building Products ManualsFlooringGlass Tile 7 lb. White Premium Thin-Set Mortar

Glass Tile Premium Thin-Set Mortar / TDS-200

1 Product Name

Glass Tile Premium Thin-Set Mortar

2 Manufacturer

Custom Building Products

Technical Services

10400 Pioneer Boulevard, Unit 3

Santa Fe Springs, CA 90670

Customer Support: 800-272-8786

Technical Services: 800-282-8786

Fax: 800- 200-7765

Email: contactus@cbpmail.net

custombuildingproducts.com

3 Product Description

With its unique blend of fine aggregate and premium white cement,

Glass Tile Premium Thin-Set Mortar offers the ultimate in bond

strength for the most demanding installation requirements for larger

format glass tile, glass tile mosaics and other difficult to bond tile and

stone. Glass Tile Premium Thin-Set Mortar is formulated to provide a

consistent bright white back drop for clear, iridescent and translucent

glass tile to accentuate its brilliance and beauty. The non-sag

properties support vertical installations so tile won’t slip and contains

excellent handling characteristics. Exceeds ANSI A118.4TE,

A118.15TE and A118.11 without the need for additives.

Note: Please refer to the glass tile manufacturer’s installation

instructions. Glass Tile Premium Thin-Set Mortar bond strengths are

determined from direct contact with the glass tile. Glass tile is

manufactured using different processes and incorporating different

features including foils, paints, metal coatings and string mesh

backing or paper mesh backings. These differences may vary the

actual bond strengths of Glass Tile Premium Thin-Set Mortar to your

specific glass tile. Always refer to the glass tile manufacturer's

installation instructions.

Key Features

Consistent bright white color accentuates glass tile

High bond strength with minimal shrinkage

Sag and slip resistant - immediately holds wall tiles in place

Suitable Tile Types

Glass

Natural stone

Vitreous, semi-vitreous or absorptive tile: ceramic, mosaic, quarry,

cement

Impervious porcelain

Other hard-to-bond tiles

Suitable Substrates

Concrete, mortar beds, masonry, Portland cement plaster

WonderBoard® Lite cement backerboard

Liquid applied waterproofing membranes such

as RedGard® and Custom® 9240

Crack prevention sheet membranes such as Crack Buster® Pro

Uncoupling membranes such as RedGard® Uncoupling Mat

Surfaces treated with MBP Multi-Surface Bonding Primer

Exterior Grade Plywood (interior residential and light commercial dry

areas)

Gypsum wallboard (interior dry areas)

Existing ceramic tile (scarified)

Fully-bonded sheet vinyl flooring (scarified)

Plastic laminates (scarified)

Cutback adhesive (see preparation instructions)

Composition of Product

Modified dry mortar, which is a proprietary blend of Portland cement,

inorganic aggregates, copolymers and chemicals

Benefits of Product in the Installation

Maximum bond strength and flexibility

Color-consistent, bright white throughout the entire application

Superior bonding to plywood and to glass and porcelain tile

Excellent handling characteristics through extended open and

adjustment times

Approved for industry-recommended interior and exterior applications

Exceeds ANSI A118.4TE, A118.15TE and A118.11 standards without

the need for additives

Recommended for interior and exterior pools and water features which

require ANSI A118.15 bonding mortars.

Glass Tile Premium Thin-Set Mortar

Published Date: 2/12/2021

Summary of content (9 pages)

PAGE 1
Glass Tile Premium Thin-Set Mortar / TDS-200 Glass Tile Premium Thin-Set Mortar 1 Product Name Glass Tile Premium Thin-Set Mortar 2 Manufacturer Custom Building Products Technical Services 10400 Pioneer Boulevard, Unit 3 Santa Fe Springs, CA 90670 Customer Support: 800-272-8786 Technical Services: 800-282-8786 Fax: 800- 200-7765 Email: contactus@cbpmail.net custombuildingproducts.
PAGE 2
Glass Tile Premium Thin-Set Mortar / TDS-200 Glass Tile Premium Thin-Set Mortar Limitations to the Product Technical Chart Do not bond directly to hardwood, Luan plywood, particle board, Property parquet, cushion or sponge-back vinyl flooring, fiberglass, plastic or Test Method Requirement Typical Results Pot Life OSB panels. Open Time (E) When setting moisture sensitive natural stone, cement or agglomerate tile use EBM-Lite™ Epoxy Bonding Mortar 100% Solids or CEG- 4 Hours A118.15 Section 5.
PAGE 3
Glass Tile Premium Thin-Set Mortar / TDS-200 Glass Tile Premium Thin-Set Mortar Bonding to Concrete Surfaces Bonding to Cutback Adhesive Concrete or plaster must be fully cured and must accept water penetration. Test by sprinkling water on various areas of the substrate. If water penetrates, then a good bond can be achieved; if water beads, surface contaminants are present, and loss of adhesion may occur. Contaminants should be mechanically removed before installation.
PAGE 4
Glass Tile Premium Thin-Set Mortar / TDS-200 Glass Tile Premium Thin-Set Mortar Curing of Product Related Products Curing time is affected by ambient and surface temperatures and humidity. Use the following as a guideline. Allow 24 hours before grouting and light traffic. Allow 7-10 days before heavy or vehicular traffic. Before exposure to heavy or vehicular traffic, assure assembly is rated “Heavy or Extra Heavy” per TCNA Service Requirements.
PAGE 5
Glass Tile Premium Thin-Set Mortar / TDS-200 Glass Tile Premium Thin-Set Mortar Coverage Glass Tile Premium Thin-Set Mortar - 7 lb. box Trowel Size Min Coverage Max Coverage Longest side of tile less than 8" use 1/4" x 1/4" x 1/4" (6 x 6 x 6 mm) Square-Notch 14 sq. ft. (1.3 M²) 15.4 sq. ft. (1.4 M²) Longest side of tile 8" to 15" use 1/4" x 3/8" x 1/4" (6 x 9.5 x 6 mm) Square-Notch 9.8 sq. ft. (0.9 M²) 10.9 sq. ft.
PAGE 6
COLOCACIÓN DE AZULEJOS Y BALDOSAS 09 30 00 MATERIALES DE INSTALACIÓN / TDS200S GLASS TILE THIN-SET MORTAR 1. Nombre del Producto Glass Tile Thin-Set Mortar 2. Fabricante Custom Building Products 13001 Seal Beach Blvd. Seal Beach, CA 90740-2757 Atención al Cliente: 800-272-8786 Asistencia Técnica: 800-282-8786 Fax: 800- 200-7765 Correo electrónico: contactus@cbpmail.net custombuildingproducts.com 3.
PAGE 7
COLOCACIÓN DE AZULEJOS Y BALDOSAS 09 30 00 4. Datos Técnicos NORMAS APLICABLES Instituto Nacional de Normalización Estadounidense (ANSI) — ANSI A108.5, A118.4, A118.5, A118.11 de las Normas Nacionales Estadounidenses para la Instalación de Azulejos y Baldosas de Cerámica Consejo Norteamericano de Azulejos y Baldosas (TCNA) — Manual de TCNA para la Instalación de azulejos y baldosas de cerámica, Método EJ171 de TCNA PROPIEDADES TÉCNICAS Supera las especificaciones de las normas de ANSI A118.4 y A118.11.
PAGE 8
COLOCACIÓN DE AZULEJOS Y BALDOSAS 09 30 00 MATERIALES DE INSTALACIÓN / TDS200S Juntas de Expansión: Las juntas de expansión, juntas de control y juntas añadidas nunca deben cubrirse con material de instalación. Las juntas deben respetarse al instalar el revestimiento y luego rellenarse con un sellador elastomérico adecuado. Recomendación: Al instalar azulejos y baldosas de vidrio transparente o translúcido, asegúrese de lograr un contacto total entre el mortero y el dorso del azulejo o baldosa.
PAGE 9
COLOCACIÓN DE AZULEJOS Y BALDOSAS 09 30 00 7. Garantía Limitada del Producto Custom Building Products garantiza al comprador original que el producto estará libre de defectos, tanto en material como en mano de obra, bajo condiciones de uso normal y apropiado, por un período de un año a partir de la fecha de la compra original. De acuerdo con esta garantía, la responsabilidad de Custom se limitará únicamente al reemplazo del producto.