Installation Guide

ManualsBrandsCustom Building Products ManualsFlooringWhite 1.5 lb. Tile Repair Mortar

Tile Repair Professional Thin-Set Mortar / TDS-133

1 Product Name

Tile Repair Professional Thin-Set Mortar

2 Manufacturer

Custom Building Products

Technical Services

10400 Pioneer Boulevard, Unit 3

Santa Fe Springs, CA 90670

Customer Support: 800-272-8786

Technical Services: 800-282-8786

Fax: 800- 200-7765

Email: contactus@cbpmail.net

custombuildingproducts.com

3 Product Description

Used to replace any type of tile, ceramic or porcelain fixture. Polymer-

modified for maximum bond strength. This unique product allows you

to replace broken tile underwater. No need to drain fountains, pools or

spas. Easy to use, cures ultra-fast and develops high early strength for

quick installations. Grout in just two hours and traffic in four. Also

excellent for quick installation of any stone or tile. Formulated with

ControlledCureTechnology®,whichinhibitswarpingandstainingof

moisture-sensitive stone and tile that occurs when installed with

traditional thin-set mortars. Exceeds ANSI A118.4 and 118.11 without

the need for additives.

Key Features

Fast-setting for repairs to damaged tile and fixtures

Works underwater

Grout the same day

Suitable Tile Types

For replacing:

Ceramic, mosaic, quarry or porcelain tile

Brick and mini brick

Cement-based precast terrazzo

Natural stone tile

Ceramic, synthetic, or porcelain soap dishes, shampoo shelves, towel

bars

Suitable Substrates

Concrete, mortar beds, masonry, Portland cement plaster

WonderBoard® Lite cement backerboard

Liquid applied waterproofing membranes such

as RedGard® and Custom® 9240

Crack prevention sheet membranes such as Crack Buster® Pro

Uncoupling membranes such as RedGard®UncouplingMat

Surfaces treated with MBP Multi-Surface Bonding Primer

Exterior Grade Plywood (interior residential and light commercial dry

areas)

Gypsum wallboard (interior dry areas)

Existing ceramic tile (scarified)

Fully-bonded sheet vinyl flooring (scarified)

Plastic laminates (scarified)

Cutback adhesive (see preparation instructions)

Limitations to the Product

Do not bond directly to hardwood, Luan plywood, particle board,

parquet, cushion or sponge-back vinyl flooring, metal, fiberglass,

plastic or OSB panels.

When setting moisture sensitive natural stone, cement or agglomerate

tileuseEBMLite™EpoxyBondingMortar100%SolidsorCEGLite™

100% Solids Commercial Epoxy Grout.

Donotusetoinstallresinbackedstone;useEBMLite™EpoxyBonding

Mortar100%Solids,CEGLite™100%SolidsCommercialEpoxyGrout

orcontactCustom's®TechnicalServicesforrecommendations.

When setting glass tile larger than 6" x 6" (15 x 15 cm), contact

Custom's®TechnicalServicesforrecommendations.

When setting dimensional stone larger than 12" x 12" (30 x 30 cm),

contactCustom's®TechnicalServicesforrecommendationsregarding

subfloor deflection requirements.

Packaging

1.5 lbs/24 oz (.68 kg/680 g) Tub

4 Technical Data

Applicable Standards

AmericanNationalStandardsInstitute(ANSI)—ANSIA108.5,A118.5,

A118.4, A118.15 and A118.11 of the American National Standards for

the Installation of Ceramic Tile ASTM International (ASTM)

ASTM C109 Standard Test Method for Compressive Strength of

Hydraulic Cement Mortars (Using 2-in or [50-mm] Cube Specimens)

ASTM C627 Standard Test Method for Evaluating Ceramic Floor Tile

Installation Systems Using the Robinson-Type Floor Tester

Resilient Floor Covering Institute - (RFCI) Recommended Work

Practices for Removal of Resilient Floor Coverings

Tile Council of North America (TCNA) - TCNA Handbook for Ceramic

Tile Installation, TCNA Method EJ171

ISO 13007-2

Tile Repair Professional Thin-Set Mortar

Published Date: 11/7/2018

Summary of content (8 pages)

PAGE 1
Tile Repair Professional Thin-Set Mortar / TDS-133 Tile Repair Professional Thin-Set Mortar 1 Product Name Tile Repair Professional Thin-Set Mortar 2 Manufacturer Custom Building Products Technical Services 10400 Pioneer Boulevard, Unit 3 Santa Fe Springs, CA 90670 Customer Support: 800-272-8786 Technical Services: 800-282-8786 Fax: 800- 200-7765 Email: contactus@cbpmail.net custombuildingproducts.
PAGE 2
Tile Repair Professional Thin-Set Mortar / TDS-133 Tile Repair Professional Thin-Set Mortar Technical Chart Property Bonding to Lightweight Cement and Gypsum Surfaces Test Method Requirement Typical Results A118.4 Section 5.3 > 20 Minutes Pass Pot Life Open Time 30 Minutes 4 Week Shear Bond Strength Glazed Wall Tile A118.4 Section 5.1.5 > 300 psi 425 - 500 psi (29.9 35.2 kg/cm²) Porcelain Tile A118.4 Section 5.2.4 > 200 psi 300 - 400 psi (21.1 28.1 kg/cm²) Quarry Tile to Plywood A118.
PAGE 3
Tile Repair Professional Thin-Set Mortar / TDS-133 Tile Repair Professional Thin-Set Mortar Movement Joint Placement Health Precautions Movement joints are required for perimeters and other changes of plane in all installations. Expansion joints and cold joints, as described in ANSI A108.01, should never be bridged with setting material. They must be brought through the tile work and filled with an appropriate elastomeric sealant, such as Custom's 100% Silicone.
PAGE 4
Tile Repair Professional Thin-Set Mortar / TDS-133 Tile Repair Professional Thin-Set Mortar Coverage SQUARE FOOT COVERAGE PER 1.5 lbs/24 oz (SQUARE METER PER 68 KG/680 G) Min Coverage Max Coverage 2 sq. ft. (0.18 M²) 3 sq. ft. (0.27 M²) Recommended minimum coverage (80% for dry areas and 95% for wet areas and exteriors). Back buttering may be necessary. Note that mortar coverage does not include backbuttering tiles.
PAGE 5
COLOCACIÓN DE AZULEJOS Y BALDOSAS 09 30 00 MATERIALES DE INSTALACIÓN / TDS133S TILE REPAIR MORTAR 1. Nombre del Producto Tile Repair Mortar 2. Fabricante Custom Building Products 13001 Seal Beach Blvd. Seal Beach, CA 90740-2757 Atención al Cliente: 800-272-8786 Asistencia Técnica: 800-282-8786 Fax: 800- 200-7765 Correo electrónico: contactus@cbpmail.net custombuildingproducts.com 3.
PAGE 6
COLOCACIÓN DE AZULEJOS Y BALDOSAS 09 30 00 4. Datos Técnicos NORMAS APLICABLES Instituto Nacional de Normalización Estadounidense (ANSI) — ANSI A108.5, A118.14 y A118.
PAGE 7
COLOCACIÓN DE AZULEJOS Y BALDOSAS 09 30 00 MATERIALES DE INSTALACIÓN / TDS133S MÉTODOS CURADO Deje curar al menos 2 horas antes de emboquillar, dependiendo de la temperatura y humedad. Se recomienda utilizar la boquilla Polyblend® o Prism® SureColor®. Deje curar otras 4 horas más antes de exponer el área al tránsito pesado. Mezcla Aproximadamente 4 oz (118 ml) de agua limpia y fría por cada 1.5 lb (0.68 kg) de Tile Repair Mortar. Mezcle enérgicamente durante 2 - 3 minutos.
PAGE 8
COLOCACIÓN DE AZULEJOS Y BALDOSAS 09 30 00 7. Garantía Limitada del Producto Custom Building Products garantiza al comprador original que el producto estará libre de defectos, tanto en material como en mano de obra, bajo condiciones de uso normal y apropiado, por un período de un año a partir de la fecha de la compra original. De acuerdo con esta garantía, la responsabilidad de Custom se limitará únicamente al reemplazo del producto.