User’s Manual OLS1000E/EXL OLS1500E/EXL OLS2000E/EXL OLS3000E/EXL CyberPower Systems Inc. www.cpsww.
IMPORTANT SAFETY INSTRUCTIONS This manual contains important instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate the UPS. CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker protection. DO NOT plug the UPS into an outlet that is not grounded. If you need to power-drain this equipment, turn off and unplug the unit.
UNPACKING USB communication cable Input power cord UPS Output power cords x2pcs User’s manual PowerPanel® Business Edition software CD Phone line Copyright © 2012 CyberPower Systems, Inc.
INSTALLING YOUR UPS SYSTEM SYSTEM BLOCK DIAGRAM Bypass Input Input Filter PFC AC/DC BUS Charger AC/DC Battery DC/DC Inverter DC/AC Control & Monitoring INV RY Output Filter Output LCD Module USB & DB9 SNMP Slot Line Mode Battery Mode Bypass Mode HARDWARE INSTALLATION GUIDE 1. Battery charge loss may occur during shipping and storage. 7.
BASIC OPERATION POWER MODULE FRONT/REAR PANEL DESCRIPTION 1. Power On/Off Button Master ON/OFF for the UPS. 2. Function Buttons Scroll up, scroll down, select and cancel LCD menu. 3. Multifunction LCD Readout Indicate status information, settings and events. 4. Input Circuit Breaker Provide input overload and fault protection. 5. Battery Backup & Surge Protected Outlets Provide battery backup and surge protection.
BASIC OPERATION BATTERY MODULE FRONT/REAR PANEL DESCRIPTION 1. Input Connector Use this input connector to daisy chain the next Battery module. Remove the connector cover for access. 2. On-board Replaceable Fuse Cover Replaceable fuse is accessible from the rear panel. It must be done by qualified personnel. 3. Output Connector Use this output Connector to connect the Battery module to the Power module or to the next Battery module. BPSE36V45A BPSE72V45A Copyright © 2012 CyberPower Systems, Inc.
BASIC OPERATION CONNECTION #1 : POWER MODULE WITH ONE BATTERY MODULE Step 1: Loosen the two screws to remove the battery cable retention bracket of the power module. Step 2: Use the battery cable of the Battery module to connect the Battery module to the Power module. Step 3: Rotate the battery cable retention bracket and tighten the two screws to fix battery cable. Copyright © 2012 CyberPower Systems, Inc.
BASIC OPERATION CONNECTION #2 : POWER MODULE WITH MULTIPLE BATTERY MODULES st Step 1: Connect the 1 Battery module to the Power module using battery cable. Step 2: Loosen the two screws to remove the battery st cable retention bracket of the 1 battery module. Step 3: Use the battery cable to connect the 2 st module to the 1 Battery module. nd Battery Step 4: Rotate the battery cable retention bracket and tighten the two screws to fix battery cable. Copyright © 2012 CyberPower Systems, Inc.
BASIC OPERATION LCD SCREEN – UPS STATUS LCD Screen UPS Status Description UPS is operating in Line Mode. UPS is operating in Battery Mode. UPS is operating in Bypass Mode. UPS is operating in ECO (Economy) Mode.* UPS is operating in Converter Mode when this icon blinking**.
BASIC OPERATION REPLACE: This icon appears if the batteries need to be replaced. Event ID Descriptions Event ID Description of Cause 1 Bus Start Fail: DC-DC converter or bus sensing circuit failed. 2 Bus Volt High: DC-DC converter failed. 3 Bus Volt Low: DC-DC converter failed. 4 Bus Unbalanced: DC-DC converter failed. 5 INV Start Fail: Inverter circuit failed. 6 7 INV Volt High: Inverter circuit or output voltage sensing circuit failed.
LCD SETUP FUNCTIONS LCD INFORMATION READOUT There are 12 types of UPS information available for display on digit area. Information Submenu Description OUTPUT XXX V Displays the Output Voltage OUTPUT XX.
LCD SETUP FUNCTIONS Configure Submenu Available Settings Default Setting Output Voltage = [208V] [220V] [230V] [240V] 230V Output Frequency = [50Hz][60Hz] 50Hz ECO Mode * [0%] (Disable) [10%][15%] (Enable) 0% Bypass Mode ** [DIS] (Disable) [ENA] (Enable) Enable Converter Mode [DIS] (Disable) [ENA] (Enable) Disable EPO/ROO*** [EPo] [Roo] EPO EBM Number**** [0] [1] [2] [3] [4] [5] [6] [7] [8] [9] [10](for –E models, the maximum number is 3 ) 0(for –E models) / 1 (for –EXL models) *) Th
MAINTENANCE Storage To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery every three months to ensure battery life. CAUTION! To avoid electric shock, turn off and unplug the UPS from the wall receptacle before servicing the battery. CAUTION! Only use tools with insulated handles. Do not lay tools or metal parts on top of the UPS or battery terminals.
TECHNICAL SPECIFICATIONS Model Configuration Capacity (VA) Capacity (Watts) Form Factor Energy-saving Technology Input Input Voltage Range Input Frequency Range Input Power Factor Cold Start Output Output Waveform Output Voltage Output Frequency Transfer Time (Typically) Rated Power Factor Harmonic Distortion Crest Factor ECO Mode Voltage Regulation UPS Outlets Protection Surge Protection Phone / Network Protection Overload Protection Short Circuit Protection OLS1000E/EXL OLS1500E/EXL OLS2000E/EXL O
TECHNICAL SPECIFICATIONS Software Power Management Software Physical Dimensions Net Weight ® PowerPanel Business Edition D×W×H = 15.51 x 5.94 x 8.86in. (394×151×225 mm) 28.9/17.0lbs 33.7/17.2lbs (13.1/7.7Kg) (15.3/7.8Kg) Safety Conformance Approvals D×W×H = 16.38 x 7.72 x 13.28in. (416×196×337 mm) 52.5/26.9lbs 62.2/27.8lbs (23.8/12.2Kg) (28.2/12.6Kg) CE Copyright © 2012 CyberPower Systems, Inc.
TROUBLE SHOOTING Problem Warning Possible Cause Solution O/P Overload Your equipment requires more power than the UPS can provide. If the UPS is in Line Mode then it will transfer to Bypass Mode; if the UPS is in Battery Mode it will shutdown. Shut off non-essential equipment. If this solves the overload problem, the UPS will transfer to normal operation. Battery Mode UPS is operating on battery power. Save your data and perform a controlledshutdown.
