User’s Manual Utility Series UPS UP425 ADDITIONAL INSTALLATION TIPS CAN BE FOUND AT: www.cyberpowersystems.com/FAQs.
TABLE OF CONTENTS IMPORTANT SAFETY WARNINGS…………….……………………………………….………1 INSTALLING YOUR UPS SYSTEM…………………….………………………………….……2 - UNPACKING…… ………………………………………………………………..2 - HARDWARE INSTALLATION GUIDE…………………………………….……2 BASIC OPERATION…………………………………………...................................................2 - FRONT PANEL AND REAR PANEL DESCRIPTION....................................2 TROUBLESHOOTING……………………………………………………….........................….4 TECHNICAL SPECIFICATIONS…………………………………………………….………..….
UP425 Guaranteed Uninterruptible Power System IMPORTANT SAFETY WARNINGS (SAVE THESE INSTRUCTIONS) This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate.
INSTALLING YOUR UPS SYSTEM UNPACKING Inspect the UPS upon receipt. The box should contain the following: (1) UPS Unit; (1) User’s Manual for UPS; (1) Warranty Registration Card; TM TM (1) PowerPanel Software Disk; (1) User’s Manual for PowerPanel ; (1) Serial Interface Cable (DB-9); (1) Serial-to-USB cable; (1) Telephone Cable HARDWARE INSTALLATION GUIDE 1. Connect the equipment to your UPS outlets.
UP425 Guaranteed Uninterruptible Power System ◆ Power Switch Press the power button to turn the UPS ON or OFF ◆ Power On Indicator This LED is illuminated when the utility condition is normal and the UPS outlets are providing “clean power”, free of surges and spikes ◆ Using Battery Indicator This illuminates during utility failure, indicating that the battery is supplying power to the battery-power supplied outlets.
TROUBLESHOOTING Problem The UPS does not perform expected runtime. The UPS will not turn on. Outlets do not provide power to equipment Possible Cause Solution Batteries are not fully charged. Recharge the battery by leaving the UPS plugged in. Battery is slightly worn out. Contact CyberPower Systems at tech@cyberpowersystems.com The on/off switch is designed to prevent damage by rapidly turning it off and on. Turn the UPS off. Wait 10 seconds and then turn the UPS on.
UP425 Guaranteed Uninterruptible Power System TECHNICAL SPECIFICATIONS Model Capacity (VA) Capacity (Watts) Input Input Voltage Range Frequency Range Output On Battery Output Voltage On Battery Output Frequency Transfer Time (Typical) Overload Protection Surge Protection and Filtering Lightning / Surge Protection Internet Ready (DSL / Phone / FAX / Modem Protection) Physical Total # of UPS Receptacles Maximum Dimensions Weight Battery Sealed Maintenance Free Lead Acid Battery User Replaceable Typical Recha
DEFINITIONS FOR ILLUMINATED LED INDICATORS Condition Power On Using Battery Wiring Fault Circuit Breaker On Off Off Set Off Normal Off On On/Off Set Two Beeps Utility Failure- The UPS is providing battery power to the Battery-Power Supplied outlets. Off On On/Off Set Rapid Beeps Utility Failure- The UPS is providing battery power. The rapid beeps indicate the battery will run out of charge within a few minutes. Overload- Occurs in the Full-time Surge Protection Outlets.
UP425 Guaranteed Uninterruptible Power System LIMITED WARRANTY AND POWER CONTROL GUARANTEE In purchasing UP425 in the United States or Canada, the original end user receives a Limited Warranty and CyberPower's Power Control Guarantee from Cyber Power Systems (USA), Inc. (for ease of reading, referred to as "CyberPower"). The Limited Warranty and the Power Control Guarantee are intended to be the original end-user's exclusive rights and remedies.
NOTE: Some States do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. To be covered you must still be the owner of the Product at the time of the failure that results in the claim made under this Limited Warranty. Exclusive Remedies Under Limited Warranty.
UP425 Guaranteed Uninterruptible Power System The Limited Warranty does not cover Connected Equipment, but as is explained below, to be covered under the Power Control Guarantee, the Connected Equipment must have been damaged due to a failure of the Product.
CyberPower’s Duties. CyberPower will inspect and examine the Product and the item(s) of Connected Equipment (or at CyberPower's election, your written statement and repair cost estimate for those item(s)). You must return the product for inspection.
UP425 Guaranteed Uninterruptible Power System 2. As to Connected Equipment, the Power Control Guarantee covers only damage within the specific terms of the Power Control Guarantee to Connected Equipment (and only up to the applicable aggregate ceiling amount). 3.
DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT OR OTHER HIGH RISK ACTIVITIES. CyberPower does not sell the Products for use in high-risk activities.
