User's Manual

WARNING: Avoid electric shock and
 re hazard! Unplug this product before
cleaning. Do not use a liquid cleaner or an
aerosol cleaner. Do not use a magnetic/
static cleaning device (dust remover) to
clean this product.
WARNING: Avoid electric shock and
 re hazard! Never push objects through the
openings in this product. Foreign objects
can cause electrical shorts that can result
in electric shock or  re.
Service Warnings
WARNING: Avoid electric shock! Do
not open the cover of this product. Opening
or removing the cover may expose you to
dangerous voltages. If you open the cover,
your warranty will be void. This product
contains no user-serviceable parts.
Check Product Safety
Upon completion of any service or repairs to this
product, the service technician must perform
safety checks to determine that this product is
in proper operating condition.
Protect the Product When
Moving It
Always disconnect the power source when
moving the apparatus or connecting or
disconnecting cables.
Telephone Equipment Notice
When using your telephone equipment, basic
safety precautions should always be followed to
reduce the risk of  re, electric stock and injury
to persons, including the following:
1. Do not use this product near water, for
example, near a bath tub, wash bowl, kitchen
sink or laundry tub, in a wet basement or near
a swimming pool.
2. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric shock
from lightning.
3. Do not use the telephone to report a gas leak
in the vicinity of the leak.
WARNING: To reduce the risk of
fire, use only No. 26 AWG or larger
telecommunication line cord.
SAVE THESE INSTRUCTIONS
United States FCC Compliance
This device has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against such interference in a residential
installation. This equipment generates, uses,
and can radiate radio frequency energy. If
not installed and used in accordance with the
instructions, it may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment OFF and ON, the user
is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit di erent from that to which the receiver
is connected.
Consult the service provider or an experienced
radio/television technician for help.
Any changes or modi cations not expressly
approved by Cisco Systems, Inc., could void
the user’s authority to operate the equipment.
The information shown in the FCC Declaration
of Conformity paragraph below is a requirement
of the FCC and is intended to supply you with
information regarding the FCC approval of
this device. The phone numbers listed are for
FCC-related questions only and not intended
for questions regarding the connection or
operation for this device. Please contact your
service provider for any questions you may
have regarding the operation or installation of
this device.
Declaration of Conformity
This device complies with Part 15 of FCC
Rules. Operation is subject to the following two
conditions: 1) the device may not cause harmful
interference, and 2) the device must accept any
interference received, including interference
that may cause undesired operation.
Manufactured by:
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134 USA
www.cisco.com/go/contacts
Canada EMI Regulation
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la class B est
conforme à la norme NMB-003 du Canada.
RF Exposure Statements
Note: This transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter. This equipment should be installed and operated with a minimum distance of 7.9
inches (20 cm) between the radiator and your body.
US
This system has been evaluated for RF exposure for humans in reference to ANSI C 95.1 (American
National Standards Institute) limits. The evaluation was based in accordance with FCC OET Bulletin
65C rev 01.01 in compliance with Part 2.1091 and Part 15.27. The minimum separation distance
from the antenna to general bystander is 7.9 inches (20 cm) to maintain compliance.
Canada
This system has been evaluated for RF exposure for humans in reference to Canada Health Code 6
(2009) limits. The evaluation was based on evaluation per RSS-102 Rev 4. The minimum separation
distance from the antenna to general bystander is 7.9 inches (20 cm) to maintain compliance.
EU
This system has been evaluated for RF exposure for humans in reference to the ICNIRP (International
Commission on Non-Ionizing Radiation Protection) limits. The evaluation was based on the EN 50385
Product Standard to Demonstrate Compliance of Radio Base Stations and Fixed Terminals for Wireless
Telecommunications Systems with basic restrictions or reference levels related to Human Exposure
to Radio Frequency Electromagnetic Fields from 300 MHz to 40 GHz. The minimum separation
distance from the antenna to general bystander is 20 cm (7.9 inches).
Australia
This system has been evaluated for RF exposure for humans as referenced in the Australian Radiation
Protection standard and has been evaluated to the ICNIRP (International Commission on Non-Ionizing
Radiation Protection) limits. The minimum separation distance from the antenna to general bystander
is 20 cm (7.9 inches).
Български
[Bulgarian]
Това оборудване отговаря на съществените изисквания и приложими
клаузи на Директива 1999/5/ЕС.
Česky
[Czech]:
Toto zařízení je v souladu se základními požadavky a ostatními odpovídajícími
ustanoveními Směrnice 1999/5/EC.
Dansk [Danish]: Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante
bestemmelser i Direktiv 1999/5/EF.
Deutsch [German]: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren
entsprechenden Vorgaben der Richtlinie 1999/5/EU.
Eesti [Estonian]: See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele
asjakohastele sätetele.
English: This equipment is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Español [Spanish]: Este equipo cumple con los requisitos esenciales asi como con otras
disposiciones de la Directiva 1999/5/CE.
Ελληνική [Greek]: Αυτός ο εξοπλισμός είναι σε συμμόρφωση με τις ουσιώδεις απαιτήσεις και
άλλες σχετικές διατάξεις της Οδηγίας 1999/5/EC.
Français [French]: Cet appareil est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la Directive 1999/5/EC.
Íslenska
[Icelandic]:
Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum
Tilskipunar 1999/5/EC.
Italiano [Italian]: Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti
dalla Direttiva 1999/5/CE.
Latviski [Latvian]: Šī iekārta atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to
saistītajiem noteikumiem.
Lietuvių
[Lithuanian]:
Šis įrenginys tenkina 1999/5/EB Direktyvos esminius reikalavimus ir kitas
šios direktyvos nuostatas.
Nederlands
[Dutch]:
Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde
bepalingen van de Richtlijn 1999/5/EC.
Malti
[Maltese]:
Dan l-apparat huwa konformi mal-ħtiġiet essenzjali u l-provedimenti l-oħra
rilevanti tad-Direttiva 1999/5/EC.
Magyar
[Hungarian]:
Ez a készülék teljesíti az alapvető követelményeket és más 1999/5/EK
irányelvben meghatározott vonatkozó rendelkezéseket.
Norsk
[Norwegian]:
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante
bestemmelser i EU-direktiv 1999/5/EF.
Polski
[Polish]:
Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi
warunkami określonymi Dyrektywą UE: 1999/5/EC.
Português
[Portuguese]:
Este equipamento está em conformidade com os requisitos essenciais e
outras provisões relevantes da Directiva 1999/5/EC.
Română
[Romanian]
Acest echipament este in conformitate cu cerintele esentiale si cu alte
prevederi relevante ale Directivei 1999/5/EC.
Slovensko
[Slovenian]:
Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji
Direktive 1999/5/EC.
Slovensky [Slovak]: Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými
nariadeniami direktív: 1999/5/EC.
Suomi [Finnish]: Tämä laite täyttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä
asetettujen muiden laitetta koskevien määräysten mukainen.
Svenska
[Swedish]:
Denna utrustning är i överensstämmelse med de väsentliga kraven och andra
relevanta bestämmelser i Direktiv 1999/5/EC.
Note: The full declaration of conformity for this product can be found at http://www.cisco.com/
web/consumer/support/compliance_info.html.
The following standards were applied during the assessment of the product against the requirements
of the Directive 1999/5/EC:
Radio: EN 300 328
EMC: EN 301 489-1 and EN 301 489-17
Safety: EN 60950 and EN 50385
The CE mark and class-2 identi er are a xed to the product and its packaging. This product
conforms to the following European directives:
-1999/5/EC
National Restrictions
This product is for indoor use only.
France
For 2.4 GHz, the output power is restricted to 10 mW EIRP when the product is used outdoors in
the band 2454 - 2483.5 MHz. There are no restrictions when used in other parts of the 2.4 GHz
band. Check http://www.arcep.fr/ for more details.
Pour la bande 2,4 GHz, la puissance est limitée à 10 mW en p.i.r.e. pour les équipements utilisés en
extérieur dans la bande 2454 - 2483,5 MHz. Il n’y a pas de restrictions pour des utilisations dans
d’autres parties de la bande 2,4 GHz. Consultez http://www.arcep.fr/ pour de plus amples détails
Italy
This product meets the National Radio Interface and the requirements speci ed in the National
Frequency Allocation Table for Italy. Unless this wireless LAN product is operating within the
boundaries of the owner’s property, its use requires a “general authorization.” Please check http://
www.comunicazioni.it/it/ for more details.
Questo prodotto è conforme alla speci che di Interfaccia Radio Nazionali e rispetta il Piano
Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all ‘interno del proprio
fondo, l’utilizzo di prodotti Wireless LAN richiede una “Autorizzazione Generale”. Consultare http://
www.comunicazioni.it/it/ per maggiori dettagli.
Latvia
The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic Communications
O ce. Please check http://www.esd.lv for more details.
2,4 GHz frekvenču joslas izmantošanai ārpus telpām nepieciešama atļauja no Elektronisko sakaru
direkcijas. Vairāk informācijas: http://www.esd.lv.
Note: The regulatory limits for maximum output power are speci ed in EIRP. The EIRP level of a
device can be calculated by adding the gain of the antenna used (speci ed in dBi) to the output
power available at the connector (speci ed in dBm).
Antennas
Use only the antenna supplied with the product.
CE Compliance
Declaration of Conformity with
Regard to the EU Directive 1999/5/
EC (R&TTE Directive)
This declaration is only valid for con gurations
(combinations of software,  rmware and hardware)
supported or provided by Cisco Systems for use
within the EU. The use of software or  rmware not
supported or provided by Cisco Systems may result
in the equipment no longer being compliant with the
regulatory requirements.
W
all Mounng
T
he DPC3928/3828 can be wall-mounted. The wall-mounng hardware is user-supplied. The
p
orts on the back front must face either upward or downward when mounng the
D
PC3928/3828 to the wall. The recommended dimensions for the mount kit are as follows:
T
o mount the DPC3928/3828 to the wall:
S
TEP 1 Determine where you want to mount the DPC3928/3828. Verify that the surface is
s
mooth, flat, dry, and sturdy.
S
TEP 2 Drill two pilot holes into the surface 96 mm apart.
S
TEP 3 Insert a screw into each hole, leaving a gap between the surface and the base of the
s
crew head of at least 22 mm.
S
TEP 4 Place the DPC3928/3828 wall-mount slots over the screws and slide the
D
PC3928/3828 down until the screws fit snugly into the wall-mount
s
lots.