2. 4G 54Mbps Wireless Et hernet Bridge Quick Installation Guide Version 2.
.4G 54Mbps Wireless AP User's Manual FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
2.4G 54Mbps Wireless AP User's Manual Table of Contents 1. INTRODUCTION .......................................................................................................... 4 THE WIRELESS ACCESS POINT FEATURES ..................................... 錯誤! 尚未定義書籤。 PACKAGE CONTENTS ...................................................................... 錯誤! 尚未定義書籤。 2. HARDWARE INSTALLATION .................................................. 錯誤! 尚未定義書籤。 PHYSICAL D ETAILS .....................................
2.4G 54Mbps Wireless AP User's Manual 1. Introduction Thank you for purchasing the WS638 Wireless Ethernet Bridge. This Ethernet Bridge provides you with an innovative wireless networking solution. The WS638 is easy to set up and use. With this innovative wireless technology, you can share files and network resources on the network—without inconvenient wires! The Wireless Ethernet Bridge Features Wireless Features l 11g Standards Compliant – The Ethernet Bridge complies with IEEE802.
2.4G 54Mbps Wireless AP User's Manual l Wireless LAN Security - Provide 64-bit & 128-bit Wired Equivalent Privacy encryption to protect the wireless data transmissions.
2.4G 54Mbps Wireless AP User's Manual 2.Hardware Installation Physical Details Rear Panel Antenna Connector Reset Button LAN Connection Power Input Reset Button “Reset” mean “ Initiation”. While pressing the button, the Ethernet Bridge will reboot and reset current configurations to factory default settings. The left indicator “ DIAG” on Ethernet Bridge will be off and then begin blinking. Then this initiation action will be completed when the indicator “ DIAG” is always green instead of blinking.
2.4G 54Mbps Wireless AP User's Manual LED Indications Power LAN Wireless-g LED Power LAN Color Green Status Orange Power on Power off Initial Hardware Error Green ON LAN port is connected. OFF No connection and neither data forwarding from LAN ports. LAN is connected and data is sending or receiving via LAN port Wireless port is connected with another wireless device. Wireless port is not connected to any device.
2.4G 54Mbps Wireless AP User's Manual Hardware Installation Following illustration is an example showing how to install Ethernet Bridge with your PC. Be sure to use the supplied power Ethernet Bridge. Note! You may also connect the Ethernet Bridge to other Ethernet-ready device, such as printer server.
2.4G 54Mbps Wireless AP User's Manual Connecting the Ethernet Bridge to Your Network There are two network scenarios as below: Also known as a peer-to-peer network, an ad-hoc network is one that allows all workstations and computers in the network to act as servers to all other users on the network. Ad-hoc Networking Users on the network can share files, print to a shared printer, and access the Internet with a shared modem.
2.4G 54Mbps Wireless AP User's Manual Wired to wireless LAN connectivity: the access point Ethernet Bridges the gap between wireless LANs and their wired counterparts.
2.4G 54Mbps Wireless AP User's Manual 3. Wireless Navigator Installation Install the Wireless Navigator The Wireless Navigator Utility is provided to allow user easily to configure the Ethernet Bridge through any Windows-based PC. This section describes procedures for installing the Wireless Navigator Utility to PC. Note! Please make sure that your PC already has TCP/IP protocol installed.
2.4G 54Mbps Wireless AP User's Manual Step 2: After InstallShield Wizard preparation finished, the following window will be shown. Click the Next button to continue. Step 3: Key in your User Name and Company Name, and click Next button to continue. Step 4: The screen will show you the default destination chosen by the utility.
2.4G 54Mbps Wireless AP User's Manual an alternate destination. Click the Next button, when you are ready to continue. The setup program will then begin to install the programs into the destination folder. Step 5: The screen will show you the Program Folder that the utility will use. You may type a new folder name to create a new program folder, or select one from the existing folder list, and click Next button to continue.
2.4G 54Mbps Wireless AP User's Manual Step 6: The Wireless Navigator has been installed now. Please click the Finish button to complete installation. Note! To remove Wireless Navigator Utility, click the Start button, and select Programs, Wireless Navigator, and Uninstall, and then follow the instruction on screen.
