Cybex 530S Stepper Owner’s Manual Cardiovascular Systems Part Number LT-18938-4 G www.cybexinternational.
Cybex 530S Stepper Owner’s Manual Cardiovascular Systems Part Number LT-18938-4 G Cybex and the Cybex logo are registered trademarks of Cybex International, Inc. Polar® is a registered trademark of Polar. DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual.
Table of Contents Front Pages About this Manual . . . . . . . . . . . . . . . . . . iii FCC Compliance Information . . . . . . . . . iii 1 Safety Important Voltage Information . . . . . . . . . Important Safety Instructions . . . . . . . . . Warning Decals . . . . . . . . . . . . . . . . . . . . Warning Decals A/V Option . . . . . . . . . . . Warning Decals - 530S Stepper . . . . . . . CSAFE Port . . . . . . . . . . . . . . . . . . . . . . . Explanation of Symbols Used . . . . . . . .
Page ii
About this Manual An Owner’s Manual is shipped with each unit. To purchase additional copies of this manual or any other Cybex manual, please do one of the following: • fax your order to 508-533-5183 • contact Cybex Customer Service at 888-462-9239 • or contact Cybex Customer Service at 508-533-4300 To contact Cybex with comments about this manual you may send email to techpubs@cybexintl.com.
Page iv
Cybex 530S Owner’s Manual 1 - Safety IMPORTANT: Read all instructions and warnings before using the unit. Important Voltage Information Before plugging the power cord into an electrical outlet, verify that the voltage requirements for your area match the voltage of the stepper that you have received. The power requirements for the unit are a grounded circuit rated for one of the following: 115 VAC ±5%, 50/60 Hz; or 230 VAC ±10%, 50/60 Hz.
Cybex 530S Owner’s Manual • Report any malfunctions, damage or repairs to the facility. • Replace any warning labels if damaged, worn or illegible. Facility Safety Precautions • Make sure all user and safety precautions are observed. • Read the Owner’s Manual carefully before assembling, servicing or using the equipment. • Make sure that all users are properly trained on how to use the equipment. • Make sure that each machine is set up and operated on a solid level surface.
Cybex 530S Owner’s Manual Steppers containing the A/V options • Devices connected to Cybex equipment must comply with appropriate safety standards. This includes but not limited to: UL-60950 and EN 60950. Warning Decals Carefully read and understand all warning decals before using the unit. NOTE: To replace any worn or damaged decals do one of the following: Visit www.cybexinternational.com to shop for parts online, fax your order to 508-533-5183 or contact Cybex Customer Service at 888-462-9239.
Cybex 530S Owner’s Manual Warning Decals - 530S Stepper Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death or serious injury. The warning decals used on the Cybex 530S Stepper are shown below. WARNING SERIOUS INJURY COULD OCCUR IF THESE PRECAUTIONS ARE NOT OBSERVED 1. Obtain a medical exam before beginning any exercise program. 2. Stop exercising if you feel faint, dizzy or experience pain and consult your physician. 3. Obtain instruction before using.
Cybex 530S Owner’s Manual CSAFE Port NOTE: The CSAFE standard defines a communication protocol and low-voltage DC power source specific to the Fitness Equipment Industry. These RJ-45 phone jacks are provided for use ONLY within the CSAFE protocol. For more information on the CSAFE standard, visit www.fitlinxx.com/csafe. NOTE: The CSAFE port inside the console, accessible through the rear access door, is the only port in the Cybex stepper that carries BOTH the CSAFE communication lines AND the 8.
Cybex 530S Owner’s Manual Explanation of Symbols Used CE - The CE (Conformitè Europèenne) mark is a European Union approval indicating that a product complies with a European Directive. Pause/End - Press to pause program. Quick Start - Press to skip Program Setup Mode and enter Manual Mode. Up Arrow - This key adjusts Program, Weight, Time, Level, Age or BPM up. Down Arrow - This key adjusts Program, Weight, Time, Level, Age or BPM down. Level Plus - This key adjusts Level up.
Cybex 530S Owner’s Manual 2 - Assembly and Setup Warnings All warnings listed in this chapter are as follows: WARNING: Use extreme caution when assembling the unit. Failure to do so could result in injury. WARNING: Always use proper lifting methods when moving heavy items. WARNING: Be sure that all electrical requirements are met as indicated in the specifications at the front of the manual and at the beginning of this chapter prior to proceeding.
Cybex 530S Owner’s Manual Electrical Power Requirements The power requirements for the unit are a grounded circuit rated for one of the following: 115 VAC ±5%, 50/60 Hz; or 230 VAC ±10%, 50/60 Hz. Contact your electrician to ensure the power supply complies with local building codes. NOTE: Do not use a ground plug adapter to adapt the 3-prong power cord plug to a non-grounded electrical outlet. Up to ten units can be daisy-chained together for single outlet use.
Cybex 530S Owner’s Manual C. Check to be sure that the following items are present. Check off ( ) each item as you find it. See Figure 1. If any of the parts are missing contact Cybex Customer Service.
Cybex 530S Owner’s Manual D. Check off ( Item 13 14 15 16 17 18 19 20 21 Qty 8 8 4 2 4 16 4 8 1 ) each item in the hardware pack as you find it. See Figure 2. Part Number HS-16950 HS-17544 HS-18127 HS-41006 HS-41109 HW-00165 HW-00180 HW-54000 EH-00472 Description Screw 5/16-18 x 7/8”, Lg HX Soc Btn Bolt, SLFTP, 5/16-18 x .75”, HXHD BLK, ZN Bolt, 1/4-20 X 1.
Cybex 530S Owner’s Manual #6 #14 #18 #19 #4 #15 #18 #5 #20 #18 #13 #14 #16 #2 #7 #14 #21 #14 #18 #18 #3 #17 #17 #1 Figure 2 Assembly and Setup Page 2-5
Cybex 530S Owner’s Manual WARNING: Always use proper lifting methods when moving heavy items. 4. Lift and move the unit #2 A. Lift and move or roll the unit using the front transport wheels to the location where you intend to leave it. Use proper lifting methods. 5. Attach the Display Upright to Base Assembly. #15 #18 #21 #15 #18 NOTE: If attaching the A/V option, refer to the 530S A/V bracket installation instructions (supplied with the A/V bracket). A.
Cybex 530S Owner’s Manual #14 #18 #2 #2 #17 #3 #4 #14 #17 Figure 5 #18 Figure 6 7. Attach the Display Handrail. A. Locate the display handrail (#4), four screws 5/16-18 x .75” (#14) and four washers 5/16” (#18). See Figure 6. B. Using a 1/2” open end wrench secure the display handrail (#4) to the display upright (#2) using four screws 5/16-18 x .75” (#14) and four washers 5/16” (#18). 8. Attach the Handrails. A.
Cybex 530S Owner’s Manual C. Using a 5/32” allen wrench secure the console back to the console upright (#4) using four screws 1/4-20 x 1.25” (#15) and four washers 1/4” (#19). See Figure 9. Console Back D. Locate the display cable, contact heart rate cable and ground wire. Insert the cables into the display board. See Figure 10. E. Place the console front in the correct position on the console back. F.
Cybex 530S Owner’s Manual #16 #7 #2 Leveling Feet Figure 12 Figure 11 11. Level the unit. A. Confirm that the unit is on a level surface. See steps 8B - 8D for leveling. WARNING: Always use proper lifting methods when moving heavy items. B. Carefully lay the stepper on its side to gain access to the leveling feet. C. Locate the leveling feet at the rear of the unit. See Figure 12. D. Using your hands, adjust the leveling feet up or down until the unit is level. 12. Connect the power cord. A.
Cybex 530S Owner’s Manual WARNING: Be sure that all electrical requirements are met as indicated in the specifications at the front of the manual and at the beginning of this chapter prior to proceeding. Testing the Operation Use the following instructions to test the full resistance of the unit. 1. Plug the power cord into a power outlet from a grounded circuit as described under Electrical Requirements in this chapter. NOTE: Coil up the remainder of the power cord and place it out of the way.
Cybex 530S Owner’s Manual Setting Operation Options 1. Enter Test Mode by holding down any key while turning on (I) power. The display will read “Step”. NOTE: After changing any value, you must press Enter to save that value. When you press enter the display will read “updt” (updated) to confirm your selection. 2. Press the Time key to set options, change values with Λ and V keys and press Enter to save your selection.
Cybex 530S Owner’s Manual This page intentionally left blank Assembly and Setup Page 2-12
Cybex 530S Owner’s Manual 3 - Operation Read and understand all instructions and warnings prior to using the unit. See all of the safety related information located in Chapter 1. Terms and Symbols Used This section lists some of the common terms and symbols used in this chapter. Other terms and symbols are listed in this chapter as appropriate. Dormant Mode - The Dormant Mode occurs when the unit is not in use. The control panel will display a beating heart when the unit is in Dormant Mode.
Cybex 530S Owner’s Manual Intended Use The intended use of this exercise equipment is to aid or improve general physical fitness and exercise. For Household or Commercial use.
Cybex 530S Owner’s Manual Quick Operation Guide NOTE: Maximum user weight is 400 lbs. (181 kg). The following is a quick overview of the operation of the unit. For more information read Detailed Operation Guide in this chapter. 1. Hold the handrails to steady yourself while you step onto the pedals. 2. Begin stepping. 3. Press any program key or press Quick Start to skip the settings and begin Manual Mode immediately. 4.
Cybex 530S Owner’s Manual 3. The unit begins with a long tone. Depending on which program and level you selected, the speed will begin to change. 4. Observe the four displays (See Figure 1): The lower right display shows the user’s current level, then shows speed in feet per minute or meters per minute. The top center display begins showing your program profile at the left side. The center display shows statistics or adjustable settings.
Cybex 530S Owner’s Manual 7. When you complete a program the unit begins a countdown, “3...2...1” and sounds a tone for each count and ends with a long tone. Workout Review displays for 20 seconds (default setting) or until you press the Pause/end key. WARNING: Wait until pedals come to a complete stop before dismounting. 8. Wait until pedals come to a complete stop before dismounting the unit. Hold the handrails to steady yourself while you step off the unit. 9. The unit returns to Dormant Mode.
Cybex 530S Owner’s Manual Data Readouts As you exercise, the Cybex 530S Stepper keeps track of the following data: Distance - The total accumulated distance, in feet or meters, during your workout. NOTE: Depending on the defaults you’ve chosen this measurement will show in English or Metric. Floors - How many floors you’ve climbed so far. Each floor is 10 vertical feet (or three meters), or roughly equal to running 100 feet on level ground.
Cybex 530S Owner’s Manual Factors that can interfere with the heart rate signal include: • excessive movement • body composition • hydration • too loose grip • too tight grip • excessive dirt, powder or oil • resting or leaning on the grips Contaminant’s, such as hand lotions, oils or body powder, may come off on the contact heart rate grips. These can reduce sensitivity and interfere with the heart rate signal. Therefore, ensure you have clean hands when using the contact heart rate.
Cybex 530S Owner’s Manual This page intentionally left blank.
Cybex 530S Owner’s Manual 4 - Preventive Maintenance Warnings All warnings listed in this chapter are as follows: WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do so could result in serious injury. WARNING: To prevent electrical shock, be sure that the unit is unplugged from the electrical outlet before performing any cleaning or maintenance procedures. Regular Maintenance Activities WARNING: All maintenance activities shall be performed by qualified personnel.
Cybex 530S Owner’s Manual Cleaning Your Cybex 530S WARNING: To prevent electrical shock, be sure that the unit is unplugged from the electrical outlet before performing any cleaning or maintenance procedures. When cleaning your unit spray a mild cleaning agent, such as a water and dish soap solution, on a clean cloth first and then wipe the unit with the damp cloth. NOTE: Do not spray cleaning solution directly on the unit. Direct spraying could cause damage to the electronics and may void the warranty.
Cybex 530S Owner’s Manual Drive Cable Maintenance WARNING: Serious injury could occur if these inspection and maintenance actions are not observed. Drive Cables Inspect the drive cables regularly for signs of wear and replace them every six to eight months with Cybex-supplied replacement cables. See Figure 1 for location of drive cables. Follow the procedure below to ensure that the cables are in good condition.
Cybex 530S Owner’s Manual Environment Static Electricity - Depending upon where you live, you may experience dry air, causing a common experience of static electricity. This may be especially true in the winter time. You may notice a static build-up just by walking across a carpet and then touching a metal object. The same can hold true while working out on your unit. You may experience a shock due to the build-up of static electricity on your body and the discharge path of the unit.
Cybex 530S Owner’s Manual 5 - Customer Service Contacting Service Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m. Eastern Standard Time. For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239. For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax 508-533-5183. Serial Number Your serial number can be found on the back of the console upright, See Figure 1.
Cybex 530S Owner’s Manual Return Material Authorization (RMA) The Return Material Authorization (RMA) system outlines the procedures to follow when returning material for replacement, repair or credit. The system assures that returned materials are properly handled and analyzed. Follow the following procedures carefully. Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will request an RMA from Cybex, if applicable.
Cybex 530S Owner’s Manual Damaged Parts Materials damaged in shipment should not be returned for credit. Shipping damages are the responsibility of the carrier (UPS, Federal Express, trucking companies, etc.). Apparent Damage - Upon receipt of your shipment, check all boxes carefully. Any damage seen with a visual check must be noted on the freight bill and signed by the carrier’s agent. Failure to do so will result in the carrier’s refusal to honor your damage claim.
Cybex 530S Owner’s Manual This page intentionally left blank Customer Service Page 5-4
Cybex 530S Owner’s Manual Appendix A - Technical Specifications Specifications Length: Width: Height: Weight of Product: Shipping Weight: Resistance Type: Programs: Console Features: Heart Rate Features: Frame Colors: Speed Range: Maximum User Weight: Connectivity: Power: Other: Options: 45” (114 cm). 31” (79 cm). 73” (185 cm). With optional A/V monitor 78” (198cm). 151 lbs. (60 kg). 173 lbs. (78 kg). Friction Belt and Flywheel.
Cybex 530S Owner’s Manual This page intentionally left blank Technical Specifications Page A-2
