Service manual

Cybex 600T Treadmill Service Manual
B. Connect the brush wear indicator wire (yellow) into the lower control
board.
C. Connect the speed sensor cable (four pin connector) into the lower
control board.
17. Attach the motor cover.
A.
Place the rear of the motor cover in the rear guide holes.
B. Lower the front end of the motor cover and install the two Phillips
head screws that hold it
in place.
Elevation Motor
Tools Required
• Phillips head screwdriver
• Block of wood 4
11
(10 cm) tall
NOTE: Two people are recommended for this procedure.
NOTE: Elevation motor must be fully stopped at its lower limit for this
procedure.
1. Turn the power off.
A. Turn the main power switch in the front panel to the off (0) position.
B. Unplug the treadmill from the power outlet.
2. Remove the motor cover.
A. Remove the two Phillips head screws that fasten the motor cover to
the frame.
B. Lift the cover from the front and remove it from the treadmill. Set the
cover and screws aside. See Figure
1.
3. Remove the elevation motor.
A. Unplug the elevation motor from the lower control board. See
Figure 11.
B. Support the front end of the treadmill on a wooden block. This will
unload the elevation swing arm.
C. Remove the lower and upper cotter pins. See Figure 12. Support the
elevation motor while removing the clevis pins.
D. Lift the elevation motor from the front end assembly.
T ab le of Conten ts
i Read All Instructions &Warnings
ii Important Safety Instructi ons
iv About This Manual
Important Voltage Information . iv
F
CC Comp li ance Information . iv
V Declaration of Conformity
vii Table of Contents
1 Safety
Warning Decals . . . . . . . . . . . 1-1
Caution Decals . . . . . . . . . . . 1-2
2 Technical Specifications
Specifications 2-1
3 Preventative Maintenance
Regular
Maintenance Activities 3-1
Running Belt Maintenance.. 3-3
4 Troubleshooting
Test
Mode 4-1
LED Functi
ons . . . . . . . . . . . 4-1
Key Functions . . . . . . . . . . . 4-2
Error
Codes , 4-2
Speed Sensor Adjustments.
4-3
5 Removal & Replacement
Running Deck . . . . . . . . . .
.. 5-1
Running Belt . . . . . . . . . . . .. 5-5
Front
Roller. . . . . . . . . . . . .. 5-5
Drive Belt. . . . . . . . . . . . . .
.. 5-5
Rear Roller. . . . . . . . . . . . . . . 5-6
Drive
Motor . . . . . . . . . . . . .. 5-7
Motor Brush . . . . . . . . . . . . 5-10
Elevation Motor 5-13
Lower Control Board 5-15
Power Cables 5-16
Une Riter 5-17
Power Switch 5-17
Power Cord Inlet 5-18
Display
Board 5-18
Heart Rate Board 5-20
Lower Display Board 5-21
Polar
Board 5- 21
Upper Display Cable 5-22
Lower Display Cable 5-24
Display Overlays 5-25
6 Diagrams
Parts
Ust . . . . . . . . . . . . . . . 6-1
Exploded View 6-3
600T
Schemat ic 6-4
7 Customer Service
Contacting Service . . . . . . . .
7-1
Serial Number &Voltage . . .. 7-1
Retum Material Authorization
( RMA) 7-1
Damaged Parts . . . . . . . . . . . 7-2
8 Index 8-1
Page 5-13