Cybex 700T Treadmill Owner’s & Service Manual Cardiovascular Systems Part Number LT-14463-4 Rev H Cybex and the Cybex logo are registered trademarks of Cybex International, Inc. Stableflex and the Stableflex logo are registered trademarks of Cybex International, Inc. Polar is a registered trademark of Polar. DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual.
IMPORTANT WARRANTY INFORMATION To validate this warranty, complete the following information and return this card to Cybex within ten days of equipment installation.
NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST CLASS MAIL PERMIT NO.
Cybex 700T Treadmill Owner’s Manual About This Manual For your convenience, all measurements and voltage requirements are listed in both English and metric units. English values are listed first, followed by metric units in parentheses. For example: 1” (2.54 cm). The 700T Treadmill is a newer model that has replaced the former 640CR model. This manual, part number LT-14463, should be referred to for 640CR questions. An Owner’s Manual is shipped with each 700T Treadmill.
Cybex 700T Treadmill Owner’s Manual Declaration of Conformity We declare that to the best of our knowledge that the fitness equipment listed below, and manufactured by: Cybex International, Inc.
Cybex 700T Treadmill Owner’s Manual Table of Contents Front Pages About this Manual . . . . . . . . . . . . . . . . . . i FCC Compliance Information . . . . . . . . . . i Declaration of Conformity . . . . . . . . . . . . ii Table of Contents . . . . . . . . . . . . . . . . . .iii 1 Safety Important Voltage Information . . . . . . . 1-1 Grounding Instructions . . . . . . . . . . . . .1-1 Important Safety Instructions . . . . . . . 1-2 Caution Labels . . . . . . . . . . . . . . . . . . 1-4 Emergency Stop .
Cybex 700T Treadmill Owner’s Manual
Cybex 700T Treadmill Owner’s Manual 1- Safety IMPORTANT: Read all instructions and warnings before using the treadmill. 1 Safety Important Voltage Information 1-1 Grounding Instructions . . . . . 1-1 Important Safety Instructions 1-2 Caution Labels. . . . . . . . . . . 1-4 Emergency Stop . . . . . . . . . 1-5 Important Voltage Information Before plugging the power cord into an electrical outlet, verify that the voltage requirements for your area match the voltage of the treadmill that you have received.
Cybex 700T Treadmill Owner’s Manual grounded, dedicated circuit, and one of the following: 115 VAC, 60 Hz and 20 amps, or 230 VAC, 60 Hz, and 15 amps, or 220/240 VAC, 50 Hz and 15 amps. Make sure that the treadmill is connected to an outlet having the same configuration as the plug. Do not use a ground plug adapter to adapt the power cord to a non-grounded outlet.
Cybex 700T Treadmill Owner’s Manual • Do not operate the treadmill if the cord is damaged, if the treadmill is not working properly, or if the treadmill has been dropped or damaged. Seek service from a qualified technician. • Do not place the cord near heated surfaces or sharp edges. • Do not use the treadmill outdoors. • Do not operate the treadmill around or where aerosol (spray) or where oxygen products are being used. Front Pages About this Manual . . . . . . . . . . i FCC Compliance Information .
Cybex 700T Treadmill Owner’s Manual Caution Labels Caution labels indicate a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. The caution labels used on the 700T are shown below. The complete parts list and exploded view is in chapter 7 of this manual and on the web. To replace any worn or damaged labels do one of the following: Visit eCybex.com to shop for parts online, or fax your order to 508-533-5183.
Cybex 700T Treadmill Owner’s Manual Front Pages About this Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents. . . . . . . . . . . iii CAUTION DO NOT USE EXCESSIVE FORCE TO TIGHTEN BELT 1 Safety Important Voltage Information 1-1 Grounding Instructions . . . . . 1-1 Important Safety Instructions 1-2 Caution Labels. . . . . . . . . . . 1-4 Emergency Stop . . . . . . . . . 1-5 2 Technical Specifications Specifications . . . . . . . . . . .
Cybex 700T Treadmill Owner’s Manual Page 1-6
Cybex 700T Treadmill Owner’s Manual 2 - Technical Specifications Specifications Front Pages About this Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents. . . . . . . . . . . iii 1 Safety Length: 82" (208 cm) Width: 33" (84 cm) Overall Height: 59" (150 cm) Important Voltage Information 1-1 Grounding Instructions . . . . . 1-1 Important Safety Instructions 1-2 Caution Labels. . . . . . . . . . . 1-4 Emergency Stop . . . . . . . . .
Cybex 700T Treadmill Owner’s Manual Page 2-2
Cybex 700T Treadmill Owner’s Manual 3 - Operation Read and understand all instructions and warnings prior to using equipment. See all of the safety related information located in chapter 1. NOTE: Maximum user weight is 400 lbs. (181 kg). Quick Operation Guide The following is a quick overview of the operation of the treadmill. For more information read Detailed Operation Guide in this chapter. 1. Mount the treadmill and place your feet on the two side rails located on each side of the running belt. 2.
Cybex 700T Treadmill Owner’s Manual dedicated circuit, and one of the following: 115 VAC, 60 Hz and 20 amps, or 230 VAC, 50 Hz, and 15 amps, or 208/220 VAC, 60 Hz and 15 amps. 2. Locate the on/off (I/O) power switch on the front end of the treadmill (next to the power cord. Toggle it to the on (I) position to supply power to the internal treadmill components and illuminate the display panel. 3.
Cybex 700T Treadmill Owner’s Manual Use the - + keys to adjust the weight number displayed in the right window to reach your current weight. The 700T accepts weights from 50 to 400 lbs. (23 to 182 kg). After five seconds, if no key has been pressed, the treadmill will accept 160 lbs. (73 kg) as the default weight and revert to the Run Mode.
Cybex 700T Treadmill Owner’s Manual Press the STOP key a second time to begin a workout review. The totals reached during your workout session will cycle and the five minute pause will end. After the workout review is finished the treadmill will automatically change to Dormant Mode. Press the STOP key a third time to interrupt workout data from cycling and to change the display to Dormant Mode.
Cybex 700T Treadmill Owner’s Manual programs P2-P6. NOTE: You cannot, however, switch from a programmed workout to any other program without ending your current workout and losing your accumulated data. Changing Workout Time — You can workout up to 995 minutes in Manual Mode. Or you can create your own program the length you wish. NOTE: You cannot change the set time on programs P2-P5. Changing Data Readouts — Press SHIFT once during a workout to review each individual set of data.
Cybex 700T Treadmill Owner’s Manual With respect to treadmills, the percent grade is roughly equal to the increase in height (rise) of the treadmill divided by the length (run) of the treadmill. The degree of incline, or the angle of the treadmill, is calculated by a different mathematical formula: the arctangent of the grade (or slope). Speed — The rate that you are traveling on the running belt. Distance — The total accumulated distance, in miles or kilometers, during your workout.
Cybex 700T Treadmill Owner’s Manual NOTE: Please note that Cybex does not recommend continuous holding of the handrails or the contact heart rate grips while running. Use of Programs 1 Safety The 700T is one of the most advanced personal fitness treadmills available. With the 700T, you choose from four different programs, all of which have nine levels of difficulty, for a total choice of thirty-six different preprogrammed options.
Cybex 700T Treadmill Owner’s Manual warm-up and cool-down period. You can warm-up by setting a slow speed for walking/jogging on the treadmill at zero incline and then gradually increase the speed to the target for your workout. Reverse this process for your cool-down period, slowing down the speed gradually and returning the incline to zero.
Cybex 700T Treadmill Owner’s Manual Front Pages About this Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents. . . . . . . . . . . iii 1 Safety Important Voltage Information 1-1 Grounding Instructions . . . . . 1-1 Important Safety Instructions 1-2 Caution Labels. . . . . . . . . . . 1-4 Emergency Stop . . . . . . . . . 1-5 3 Operation Quick Operation Guide . . . . 3-1 Detailed Operation Guide . . 3-1 Stopping the Treadmill. . . . .
Cybex 700T Treadmill Owner’s Manual P3 — Cardiovascular Program The P3 Cardiovascular Program is a thirty-minute workout that uses high-intensity, aerobic exercise to strengthen the heart muscle, stressing the heart at about 70% to 85% of its maximum pumping rate. Cardiovascular Program Profile — The P3 Program consists of an initial four-minute warmup segment of relatively mild increases in speed and incline. This is followed by a twelveminute segment of automatic increases in speed and % grade.
Cybex 700T Treadmill Owner’s Manual Front Pages About this Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents. . . . . . . . . . . iii 1 Safety Important Voltage Information 1-1 Grounding Instructions . . . . . 1-1 Important Safety Instructions 1-2 Caution Labels. . . . . . . . . . . 1-4 Emergency Stop . . . . . . . . . 1-5 3 Operation Quick Operation Guide . . . . 3-1 Detailed Operation Guide . . 3-1 Stopping the Treadmill. . . . .
Cybex 700T Treadmill Owner’s Manual P4 — Weight Loss Program The P4 Weight Loss Program is a forty-five-minute walking workout designed to help you lose weight. In this program, weight loss is based on the length of time you exercise. Exercising at a lower intensity allows you to handle a longer duration and distance workout and thus burn more calories.
Cybex 700T Treadmill Owner’s Manual Front Pages About this Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents. . . . . . . . . . . iii 1 Safety Important Voltage Information 1-1 Grounding Instructions . . . . . 1-1 Important Safety Instructions 1-2 Caution Labels. . . . . . . . . . . 1-4 Emergency Stop . . . . . . . . . 1-5 3 Operation Quick Operation Guide . . . . 3-1 Detailed Operation Guide . . 3-1 Stopping the Treadmill. . . . .
Cybex 700T Treadmill Owner’s Manual P5 — Fitness Test Program The P5 Fitness Test Program is a twenty-minute walking workout designed to test your aerobic walking capacity. It is the guide by which you determine which fitness “L” level is best suited to your current performance capability and physical condition. If you successfully complete the twenty-minute test at a certain fitness level (L1...L9), you are capable of training in the other programs (P2, P3, and P4) at that same “L” level number.
Cybex 700T Treadmill Owner’s Manual Front Pages About this Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents. . . . . . . . . . . iii 1 Safety Important Voltage Information 1-1 Grounding Instructions . . . . . 1-1 Important Safety Instructions 1-2 Caution Labels. . . . . . . . . . . 1-4 Emergency Stop . . . . . . . . . 1-5 3 Operation Quick Operation Guide . . . . 3-1 Detailed Operation Guide . . 3-1 Stopping the Treadmill. . . . .
Cybex 700T Treadmill Owner’s Manual P6 — Saved Program In addition to the four programmed workouts included with the 700T, you can also create your own workout by manually changing the speed and/or incline as you exercise. You increase or decrease the speed and incline settings, using SPEED - + keys and v^ arrows. You can even create a workout to mimic a route you normally run or walk outside. When you design your own program, be sure to include a three to five minute warm-up and cool-down period.
Cybex 700T Treadmill Owner’s Manual Workout Tips Front Pages About this Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents. . . . . . . . . . . iii Monitoring Your Heart Rate 1 Safety Exercise doesn't have to be painful to be effective.
Cybex 700T Treadmill Owner’s Manual Visit our website at www.ecybex.com/education to use the body mass calculator, calorie calculator, and to get performance training tips.
Cybex 700T Treadmill Owner’s Manual 4 - Preventive Maintenance Front Pages About this Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents. . . . . . . . . . . iii Regular Maintenance Activities Preventive maintenance activities must be performed to maintain normal operation of your treadmill. Keeping a log sheet of all maintenance actions will assist you in staying current with all preventive maintenance activities.
Cybex 700T Treadmill Owner’s Manual To clean the motor components, you must remove the two Phillips head screws that hold the motor cover in place. Lift the cover, and put it and the screws aside. Use a vacuum attachment or hand vacuum to clean the exposed elevation assembly, drive motor, lower electronics and the surrounding areas. Also use a dry cloth for the areas that you can't reach with the vacuum cleaner.
Cybex 700T Treadmill Owner’s Manual Top View Front Pages About this Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents. . . . . . . . . . . iii 3 Operation Protruding Tabs Bolts Figure 1 Re-tensioning and Re-centering the Belt — Follow the procedure below. Tools Required • 3/4" wrench Quick Operation Guide . . . . 3-1 Detailed Operation Guide . . 3-1 Stopping the Treadmill. . . . . 3-3 Control During Operation . . 3-4 Data Readouts. . . .
Cybex 700T Treadmill Owner’s Manual same bolt. Once the running belt has been adjusted closer to the center of the treadmill use about 1/4 of a turn until the belt has been stabilized. B. After the belt has been centered, check the belt tension again. Make sure the running belt tension is tight enough so that the belt does not slip or hesitate when stepped on. Walk on the treadmill at 3.5-4 mph (5.6-6.4 kph) and every 4th to 5th step throw your weight into your step to feel if the belt is slipping.
Cybex 700T Treadmill Owner’s Manual Screws (2) End Caps Screws Side Rails Front Pages About this Manual . . . . . . . . . . i FCC Compliance Information . i Declaration of Conformity . . . . ii Table of Contents. . . . . . . . . . . iii 3 Operation Screws (2) Motor Cover Figure 2 B. Run your hand under the belt on the top of the deck surface. If you feel excessive ridges or cracks, or if the deck feels grooved yet highly polished, the deck should be flipped so that an unused surface faces the top.
Cybex 700T Treadmill Owner’s Manual Other Preventive Maintenance Cybex recommends that the following maintenance activities be completed by a qualified service technician. These activities should be performed at the recommended intervals listed in the Service Schedule (located in this chapter): Measure the motor brushes and replace worn motor brushes Rotate, flip and replace the running deck.
Cybex 700T Treadmill Owner’s Manual Service Schedule R cu ck he X X X X X X X X X X X X X X X X X X X X X X X X X X X Va C Odometer Reading in Miles (Km) 500 (805) m1: 5000 (8046) m2: 10000 (16093) 10500 (16898) m3: 15000 (24140) m4: 20000 (32187) 20500 (32992) m5: 25000 (40234) m6: 30000 (48280) 30500 (49085) m7: 35000 (56327) m8: 40000 (64374) 40500 (67178) m9: 45000 (72420) m10: 50000 (80467) 50500 (81272) m11: 55000 (88514) m12: 60000 (96560) 60500 (97365) m13: 65000 (104607) m14: 70000 (112654)
Cybex 700T Treadmill Owner’s Manual Log Sheet Serial Number Date of Data Collection Total Miles/Kilometers Total Hours Motor Current @ 3 mph (4.8 kph) Motor Voltage @ 10 mph (16.1 kph) - without load - with 160 lbs. load (72 kg) Notes: Total Miles/Kilometers Total Hours Motor Current @ 3 mph (4.8 kph) Motor Voltage @ 10 mph (16.1 kph) - without load - with 160 lbs. load (72 kg) Notes: Total Miles Total Hours Motor Current @ 3 mph (4.8 kph) Motor Voltage @ 10 mph (16.1 kph) - without load - with 160 lbs.
Cybex 700T Treadmill Owner’s Manual 5 - Setup & Assembly Front Pages 3 Operation Quick Setup Quick Setup - For Experienced Fitness Professionals Only 1. The power requirements for this treadmill are a grounded, dedicated circuit, and one of the following: 115 VAC, 60 Hz and 20 amps, or 230 VAC, 50 Hz, and 15 amps, or 208/220 VAC, 60 Hz and 15 amps. The location should be level, with good ventilation, and not in an area of high humidity. 2.
Cybex 700T Treadmill Owner’s Manual Item Qty 1 1 2 1 3 1 4 1 5 1 6 16 7 16 8 2 9 1 10 2 Figure 1 Page 5-2 Description Base Left upright Right upright Console assembly Upright cross brace Button head screws Star washers Phillips head screws Motor cover Front wheels
Cybex 700T Treadmill Owner’s Manual vapor, chlorine, and/or bromine could adversely affect the electronics as well as other parts of the machine. A comfortable environment will help you enjoy your exercise routine and give you additional motivation to continue. Electrical Power Requirements This treadmill is for use on a grounded, dedicated circuit, and one of the following: 115 VAC, 60 Hz and 20 amps, or 230 VAC, 60 Hz, and 15 amps, or 220/240 VAC, 50 Hz and 15 amps.
Cybex 700T Treadmill Owner’s Manual Assembling the Treadmill To ensure correct assembly of the treadmill, carefully follow these steps: NOTES: • In this manual the words “left” and “right” denote the treadmill user's point of view. • Two people are needed to assemble this treadmill. • Leave the anti-static foam on the console until the treadmill is completely assembled.* 1. Move the base into position. A.
Cybex 700T Treadmill Owner’s Manual 4. Attach the console to the left upright. A. Place the console assembly on the floor with the display side facing down and place the left upright on the floor with the decal end farthest away from the console. See Figure 5. B. Thread the display cable through the inside of the left upright from top to bottom. See Figure 5. C. Pull the cable out of the bottom of the upright. See Figure 5. D.
Cybex 700T Treadmill Owner’s Manual ! CAUTION: Be sure that the display cable does not get pinched, cut or damaged during this process. 5. Attach the console and left upright to the treadmill. A. Grasp the display cable and hold it against the inside face of the upright while lifting the console and attached left upright assembly. B. Place the assembly in position on the treadmill base. See Figure 6. Keep the display cable away from the elevation rack.
Cybex 700T Treadmill Owner’s Manual 7. Connect the cables. Front Pages A. Note that there are four threaded holes on the treadmill's front frame used to fasten the front end panel to the treadmill base. Temporarily insert button head screws in the two bottom threaded screw holes. Screw the screws in approximately halfway. See Figure 7. B. Pick up the front panel and hold it parallel to the floor, with the printed circuit board facing up.
Cybex 700T Treadmill Owner’s Manual C. Place the front end panel in position on the front of the treadmill. See Figure 8. D. Using the Allen wrench, attach the front end panel with four button head screws and four star washers. See Figure 8. Front Panel 9. Attach the motor cover. A. Place the motor cover in position on the base. See Figure 9. B. Using a Phillips head screwdriver, tighten the two screws to fasten the motor cover to the base. See Figure 9.
Cybex 700T Treadmill Owner’s Manual Test the 700T Operation Front Pages 3 Operation Use the following instructions to test the full speed and incline range of the treadmill and to check the belt for proper operation. ! CAUTION During this procedure STAY OFF THE RUNNING BELT! Stand with your feet on the side platforms. 1.
Cybex 700T Treadmill Owner’s Manual 9. Observe the belt to see that it is running properly; it should stay centered in the middle of the deck. If you have problems with the running belt operation, see Running Belt Adjustments in the Preventive Maintenance chapter. 10. Run the treadmill through its full speed range. First press the SPEED + key until the treadmill reaches its highest speed, 10 mph (16.1 kph). Then press the SPEED - key until the treadmill is back to 1.0 mph (1.6 kph).
Cybex 700T Treadmill Owner’s Manual Setting Operation Options Front Pages 3 Operation The 700T's Setup Mode allows you to configure the following features: 1. Memory Retention Mode 2. Metric/English Measurement Units 3. Programs On/Off Mode 4. Time Limits (in Manual Mode, only) 5. Pause On/Off Mode 6.
Cybex 700T Treadmill Owner’s Manual Memory Retention On: When this feature is enabled (“on”), the 700T uses your last program values as the new default program, level, and weight, replacing P1 and 160 lbs. (73 kg) as the standard defaults. The memory retention feature is convenient, if you consistently use the same program routine, because it allows you to quickly start the treadmill by simply pressing START twice. The stored default values are automatically entered from the last workout.
Cybex 700T Treadmill Owner’s Manual selected, the pause function is turned off and not available for use. To toggle between “on” and “oFF,” use the v^ keys. 6. Service Reminders Service Reminders occur every 5000 miles to bring your attention to the regular scheduled maintenance which should be performed for maximum treadmill life and performance. Use the - + keys to toggle the feature on / oFF*. Press ENTER to accept any changes and exit Setup Mode.
Cybex 700T Treadmill Owner’s Manual Page 5-14
Cybex 700T Treadmill Owner’s Manual 6 - Customer Service Front Pages 3 Operation Contacting Service Hours of phone service are Monday through Thursday from 8:30 a.m. to 6:00 p.m. and Friday from 8:30 a.m. to 5:00 p.m. Eastern Standard Time. For Cybex customers living in the USA, contact Cybex Customer Service at 800-766-3211. Your options at this number include: • Press 63 to place a parts order or to check parts order status.
Cybex 700T Treadmill Owner’s Manual warranty shall be strictly and exclusively limited to repairing or replacing free of charge, F.O.B. origin, those parts and materials which are, in Seller's judgment, defective.
Cybex 700T Treadmill Owner’s Manual said manufacturer to Seller. In this regard, Seller agrees to certify to Buyer the identity of the supplier of items claimed to be defective so the Buyer may pursue warranty claims against that party. EXPIRATION OF LIMITED WARRANTIES FOR CONSUMER BUYERS: The PG 400, 400S and 300T are warranted for residential use only. The 400T and 410T are warranted for residential and light commercial use only.
Cybex 700T Treadmill Owner’s Manual PROCEDURE FOR OBTAINING WARRANTY PERFORMANCE: TO SECURE THIS WARRANTY IN EVENT OF A DEFECT, BUYER MUST RETURN TO SELLER THE WARRANTY REGISTRATION CARD. CONTACT THE CYBEX CUSTOMER SERVICE DEPARTMENT WITH QUESTIONS REGARDING YOUR WARRANTY BY MAIL OR TELEPHONE FOR INSTRUCTIONS OR A RETURN AUTHORIZATION NUMBER AS PROVIDED BELOW. Attn: Customer Service Department Cybex International, Inc.
Cybex 700T Treadmill Owner’s Manual NOTE: Merchandise returned without an RMA number on the outside of the package or shipments sent C.O.D. will not be accepted by the Cybex receiving department. Damaged Parts Materials damaged in shipment should not be returned for credit. Shipping damages are the responsibility of the carrier (UPS, Federal Express, trucking companies, etc.) Apparent Damage — Upon receipt of your shipment, check all boxes carefully.
Cybex 700T Treadmill Owner’s Manual Page 6-6
Cybex 700T Treadmill Owner’s Manual 7 - Service Front Pages About this Manual . . . . . . . . . . i 3 Operation Service Instruction ! WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do so could result in serious injury. These activities should be performed at the recommended intervals listed in the Service Schedule in the Preventive Maintenance chapter: Measure the motor brushes and replace worn motor brushes Rotate, flip and replace the running deck.
Cybex 700T Treadmill Owner’s Manual ! WARNING: Keep wet items away from inside parts of the treadmill. Electrical shock could occur even if the treadmill is unplugged. 1. Turn the power on. A. With the power cord plugged in turn the main power switch to the on (I) position. 2. Elevate the treadmill. A. Without standing on the belt, press the START/ENTER key and begin running the treadmill. B. Press the ^ arrow and elevate the treadmill fully. 3. Turn the power off. A.
Cybex 700T Treadmill Owner’s Manual Front Pages About this Manual . . . . . . . . . . i 3 Operation Front Panel - + !WARNING: Avoid Touching R34 and Black Capacitors Motor Cable 4 Preventive Maintenance Figure 1 be pitted or blackened on one edge. Too many of these indicate a worn commutator, and the motor should be replaced. The commutator may be cleaned with narrow commutator stone if carbon build-up is present. (File down the stone if it won’t fit in the brush holder hole.
Cybex 700T Treadmill Owner’s Manual 10. Secure the front panel. A. Avoid touching R34 and the black capacitors. Connect the motor cable. See Figure 1. B. Using a 3/16” Allen wrench, secure the front panel to the frame with the four button head screws and four starwashers. 11. Secure the motor cover. A. Lower the motor cover in position and install the two Phillips head screws that hold it in place. 12. Turn the power on. A. Connect the treadmill to the power outlet. B.
Cybex 700T Treadmill Owner’s Manual displayed should not exceed 10.9 for a 115V unit, and 9.1 for a 220V unit. With a user of any weight, the current should not exceed 17.9 for a 115V unit and 15.4 for a 220V unit. If higher current values are shown, the next higher mileage service interval should be performed. Measure Motor Voltage at Max Speed, No Load A qualified Cybex service technician should perform this test.
Cybex 700T Treadmill Owner’s Manual 3. Remove the motor cover and side rails. A. Remove the two Phillips head screws that fasten the motor cover to the frame. Lift the cover and set it aside. This will allow you to remove the side rails. B. Using a 3/16” Allen wrench, remove the two button head screws on the sides of each side rail. C. Grasp the top edge of each side rail and pull up and away from the deck. This will enable you to see the deck and edges of the belt.
Cybex 700T Treadmill Owner’s Manual 10 mph (16 kph) with no load should not go below 168 VDC. If it is below 83/168 VDC respectively, the magnets are weak and the drive motor should be replaced. Press STOP to end the test. 7. Secure the front panel. A. Using a 3/16” Allen wrench, secure the front panel to the frame with the four button head screws and four starwashers. 8. Secure the side rails and motor cover. A. Snap the side rails back down into their original position. B.
Cybex 700T Treadmill Owner’s Manual A. Using a 3/16” Allen wrench, remove the two button head screws that fasten each side rail to the frame. This step will also loosen the end caps. B. Grip the top edge of each side rail and firmly pull it up and outward from the treadmill. 4. Remove the rear roller. A. Using a 3/4” wrench, remove the two rear roller bolts. Loosen each bolt evenly, making sure not to loosen either bolt too many turns before moving to the other bolt.
Cybex 700T Treadmill Owner’s Manual 7. Remove the front roller. A. Using a 1/2” wrench, remove the two screws and four washers that fasten the front roller to the front end assembly. B. Lift and slide the front roller out of the drive belt and running belt. 8. Remove the running deck and running belt. A. If you are rotating or flipping the deck make a note on the deck so you know which way it was positioned. This way, you can be sure to use all four deck positions before replacing the deck.
Cybex 700T Treadmill Owner’s Manual 12. Attach the drive belt tensioning assembly. A. Place the drive belt tensioning roller in position under the front bracket on the drive belt tensioning assembly. See Figure 3. B. Place the two steel bar springs over the drive belt tensioning roller plate and under the front bracket on the drive belt tensioning assembly. Be sure springs are firmly seated against the stop under the drive belt retainer. C. Be sure that the pulley is aligned with the drive belt. D.
Cybex 700T Treadmill Owner’s Manual Running Belt Adjustments in the Preventive Maintenance chapter. Then continue with step 17. 17. Attach the motor cover. A. Lower the motor cover and in position and install the two Phillips head screws that hold it in place. Error Codes Cybex provides error code descriptions for your information. Cybex recommends that these errors be addressed by a qualified service technician.
Cybex 700T Treadmill Owner’s Manual suspect the lower board and then the display board. This signal can also be seen on a diagnostic LED of the display board. If the drive motor (and running belt) does not rotate at all, the problem is more difficult to diagnose. First, suspect the power relay and check it by going into diagnostics, d13, and press the v elevation button in conjunction with the SPEED + button. This will toggle the relay on/off.
Cybex 700T Treadmill Owner’s Manual voltage. The cause of this error can usually be attributed to noise or “interference” from the power line. An electrical device with a high speed motor, such as a vacuum, blender, or power saw, on a local power line can sometimes cause this error. If this error occurs, check to make sure the treadmill is installed on a dedicated line and re-cycle the power to the machine by switching the main ON/OFF power switch to “OFF” for five seconds and then switching it back “ON.
Cybex 700T Treadmill Owner’s Manual Cybex service representative or directly to Cybex Technical Support. An authorized Cybex technician can usually detect the source of the problem with a service visit. ERR 7: Loss of Novram This error code indicates a problem with the nonvolatile random access memory (NOVRAM) contents. The NOVRAM chip is located in the DDM (Digital Display Module). Its contents may have become lost or destroyed. Among other data, this chip holds the accumulated miles and time information.
Cybex 700T Treadmill Owner’s Manual To exit the diagnostic test mode, press the STOP key at any time. This will return you to the mode you were in before entering Diagnostic Tests. Front Pages About this Manual . . . . . . . . . . i 3 Operation d1: Software Revision and Heart Rate Sensor This test displays the configuration information for the main program chip in the control panel.
Cybex 700T Treadmill Owner’s Manual Active keys during this test (hold keys for two seconds): START/ENTER will advance you to the next diagnostic test. STOP will exit and return you to the mode you were in before entering Diagnostic Tests. SHIFT backs you up one step in the diagnostics test menu. The - and + keys change the speed set point. The v^ arrow keys change the elevation set point. d4: Incline Sensor Test This test allows you to elevate the treadmill up and down using the v^ arrow keys.
Cybex 700T Treadmill Owner’s Manual For example, for the + key: d6 64 Front Pages About this Manual . . . . . . . . . . i Active keys during this test (hold keys for two seconds): START/ENTER will advance you to the next diagnostic test. STOP will exit and return you to the mode you were in before entering Diagnostic Tests. SHIFT backs you up one step in the diagnostics test menu. d7: Total Time This test displays the total accumulated time to date, in hours, that the treadmill has been used.
Cybex 700T Treadmill Owner’s Manual SHIFT backs you up one step in the diagnostics test menu. d9: Number of Starts This test displays the total accumulated distance to date, in miles (km), that the treadmill has been used. The diagnostic test number d9 is displayed in the left control panel window. The right control panel window displays the number of times that the treadmill has been started if 9,999 or less.
Cybex 700T Treadmill Owner’s Manual sequence displayed in the left window. Front Pages About this Manual . . . . . . . . . . i Example 1: d11 4 3 Operation 6 Example 1 shows that error code number 6 was generated four error messages ago. ERROR CODE NUMBERS 1: No speed signal at startup 2: Excessive current draw 3: Loss of speed signal 4: No frequency lock 5: Elevation error 6: Overspeed 7: Loss of NOVRAM Only one error code from the log can be displayed at any time.
Cybex 700T Treadmill Owner’s Manual To turn off a Service Reminder, press the + key, and the right window will display the Service Reminder clear command (nnC). Example 2: ErrC nnC Press START to accept the clear command(s) and advance to d1. Active keys during this test (hold keys for two seconds): START/ENTER will accept the displayed state of the Error Log and Service Reminder and advance you to the first diagnostic test.
Cybex 700T Treadmill Owner’s Manual To exit the diagnostic test mode, press STOP to return the treadmill to its previous state. Front Pages About this Manual . . . . . . . . . . i 3 Operation NOTE: If you were in the middle of a program before entering the Diagnostic Test Mode, you will be returned to the exact spot in the program where you left off. The speed, elevation, and time will all return to where they were prior to entering the diagnostic test mode.
Cybex 700T Treadmill Owner’s Manual ITEM QTY. NO. PART NO. DESCRIPTION ITEM QTY. NO. PART NO.
Cybex 700T Treadmill Owner’s Manual ITEM QTY. NO. PART NO.
Cybex 700T Treadmill Owner’s Manual Page 7-24
Cybex 700T Treadmill Owner’s Manual Page 7-25
M SK-15161 115V SK-16230 220V F RED F M AW-14251 CABLE,ELEV.