Service manual

5 - Setup & Assembly
Quick Setup
Quick Setup - For Experienced Fitness Professionals Only
1. The power requirements for this treadmill are a grounded, dedicated circuit,
and one of the following: 115 VAC, 60 Hz and 20 amps, or 230 VAC, 50
Hz, and 15 amps, or 208/220 VAC, 60 Hz and 15 amps. The location
should be level, with good ventilation, and not in an area of high humidity.
2. Assemble the treadmill using the instructions in the Setup &
Assembly chapter.
3. Operate treadmill at all speeds and elevations to confirm
proper operation.
4. Connect CSAFE equipment if applicable.
5. Refer to Setting Operations Options to see if any changes are
necessary; in most cases, the default values are the desired settings.
Choosing & Preparing a Site
Before you assemble the treadmill be sure to select a suitable site and have the
proper electrical outlet power available for optimum operation and safety. See
the Electrical Power Requirements section below for direction in locating your
treadmill's voltage requirements.
The area you select for the 700T should be well lit and well ventilated. Locate
the treadmill on a structurally sound and level surface (do not place in recessed
areas or on plush carpet) a few feet away from walls and other equipment.
Each side of the treadmill should have a 39” (1 m) minimum space. Behind the
treadmill should be 78” (2 m) minimum of space. Allow enough clearance for
safe access and passage during use of the machine. If the 700T is to be
located above the first floor, place it near or above major support beams. If the
area has a heavy, plush carpet, the airflow around the base of the machine may
be restricted or the carpeting may interfere with the moving parts. To protect
the carpeting and the machinery, place a 3/4” (1.9 cm) thick wood base under
the treadmill.
Do not install the 700T in an area of high humidity, such as in the vicinity of a
steam room, sauna, indoor pool, or outdoors. Exposure to extensive water
Cybex 700T Treadmill Owner’s Manual
Page 5-1
Front Pages
3 Operation
Quick Operation Guide . . . . 3-1
Detailed Operation Guide . . 3-1
Stopping the Treadmill. . . . . 3-3
Control During Operation . . 3-4
Data Readouts. . . . . . . . . . . 3-5
Selecting Programs &
Options. . . . . . . . . . . . . . . 3-6
Displaying Heart Rate . . . . . 3-6
Use of Programs . . . . . . . . . 3-7
P1 - Manual Mode. . . . . . . . 3-7
P2 - Speed Challenge. . . . . 3-8
P3 - Cardiovascular
Program . . . . . . . . . . . . . 3-10
P4 - Weight Loss Program 3-12
P5 - Fitness Test Program. 3-14
P6 - Saved Program . . . . . 3-16
Workout Tips . . . . . . . . . . . 3-17
4 Preventive Maintenance
Regular Maintenance
Activities. . . . . . . . . . . . . . 4-1
Cleaning Your Treadmill. . . . 4-1
Running Belt Maintenance . 4-2
Other Preventive
Maintenance . . . . . . . . . . . 4-6
Service Schedule . . . . . . . . . 4-7
Log Sheet. . . . . . . . . . . . . . . 4-8
5 Setup & Assembly
Quick Setup . . . . . . . . . . . . 5-1
Choosing & Preparing a Site 5-1
Electrical Power
Requirements . . . . . . . . . . 5-3
Unpacking . . . . . . . . . . . . . . 5-3
Assembling the Treadmill . . . 5-4
Testing the 700T Operation. 5-9
Setting Operation Options. 5-10
6 Customer Service
Contacting Service. . . . . . . . 6-1
Serial Number & Voltage. . . . 6-1
Warranty. . . . . . . . . . . . . . . . 6-1
Return Material Authorization
(RMA) . . . . . . . . . . . . . . . . 6-4
Damaged Parts. . . . . . . . . . . 6-4
Ordering Parts . . . . . . . . . . . 6-5
7 Service
Service Instruction . . . . . . . . 7-1
Motor Brushes. . . . . . . . . . . 7-1
Motor Current & Voltage . . . 7-4
Running Belt & Deck. . . . . . 7-7
Drive Belt. . . . . . . . . . . . . . . 7-9
Front Roller . . . . . . . . . . . . . 7-9
Rear Roller. . . . . . . . . . . . . 7-10
Error Codes. . . . . . . . . . . . 7-11
Diagnostic Tests . . . . . . . . 7-14
Parts List . . . . . . . . . . . . . . 7-21
Exploded View . . . . . . . . . . 7-25
700T Schematic . . . . . . . . . 7-26