Service manual

7. Connect the cables.
A. Note that there are four threaded holes on the treadmill's front frame
used to fasten the front end panel to the treadmill base. Temporarily
insert button head screws in the two bottom threaded screw holes.
Screw the screws in approximately halfway. See Figure 7.
B. Pick up the front panel and hold it parallel to the floor, with the
printed circuit board facing up. Temporarily mount the panel by
placing it over the two button head screws on the treadmill's front
end as referenced in the previous step. Use the screws to support
the panel much like a shelf. See Figure 7.
C. Ensure the black mark on the display cable is visible, and wire tie it
to the frame as it exits the upright. See Figure 7.
D. Pinch the retaining clips (to open them) and route the display cable
through each of them across the top of the treadmill. See Figure 7.
Close the retaining clips.
E. Plug all cables into the lower board: (from left to right) the
motor/choke connector, the elevation connector, the display cable
connector and the speed sensor connector. See Figure 7.
8. Attach the front panel.
A. Remove the front
panel (with the
cable connectors
still attached) off
the two button
head screws. See
Figure 7.
B. While holding the
panel close to the
treadmill, remove
the two button head
screws previously
used to support the
front end of the
treadmill base.
Cybex 700T Treadmill Owner’s Manual
Page 5-7
Front Pages
3 Operation
Quick Operation Guide . . . . 3-1
Detailed Operation Guide . . 3-1
Stopping the Treadmill. . . . . 3-3
Control During Operation . . 3-4
Data Readouts. . . . . . . . . . . 3-5
Selecting Programs &
Options. . . . . . . . . . . . . . . 3-6
Displaying Heart Rate . . . . . 3-6
Use of Programs . . . . . . . . . 3-7
P1 - Manual Mode. . . . . . . . 3-7
P2 - Speed Challenge. . . . . 3-8
P3 - Cardiovascular
Program . . . . . . . . . . . . . 3-10
P4 - Weight Loss Program 3-12
P5 - Fitness Test Program. 3-14
P6 - Saved Program . . . . . 3-16
Workout Tips . . . . . . . . . . . 3-17
4 Preventive Maintenance
Regular Maintenance
Activities. . . . . . . . . . . . . . 4-1
Cleaning Your Treadmill. . . . 4-1
Running Belt Maintenance . 4-2
Other Preventive
Maintenance . . . . . . . . . . . 4-6
Service Schedule . . . . . . . . . 4-7
Log Sheet. . . . . . . . . . . . . . . 4-8
5 Setup & Assembly
Quick Setup . . . . . . . . . . . . 5-1
Choosing & Preparing a Site 5-1
Electrical Power
Requirements . . . . . . . . . . 5-3
Unpacking . . . . . . . . . . . . . . 5-3
Assembling the Treadmill . . . 5-4
Testing the 700T Operation. 5-9
Setting Operation Options. 5-10
6 Customer Service
Contacting Service. . . . . . . . 6-1
Serial Number & Voltage. . . . 6-1
Warranty. . . . . . . . . . . . . . . . 6-1
Return Material Authorization
(RMA) . . . . . . . . . . . . . . . . 6-4
Damaged Parts. . . . . . . . . . . 6-4
Ordering Parts . . . . . . . . . . . 6-5
7 Service
Service Instruction . . . . . . . . 7-1
Motor Brushes. . . . . . . . . . . 7-1
Motor Current & Voltage . . . 7-4
Running Belt & Deck. . . . . . 7-7
Drive Belt. . . . . . . . . . . . . . . 7-9
Front Roller . . . . . . . . . . . . . 7-9
Rear Roller. . . . . . . . . . . . . 7-10
Error Codes. . . . . . . . . . . . 7-11
Diagnostic Tests . . . . . . . . 7-14
Parts List . . . . . . . . . . . . . . 7-21
Exploded View . . . . . . . . . . 7-25
700T Schematic . . . . . . . . . 7-26
Motor
Elevation
Front
Panel
Display
Speed Sensor
Temporarily
Insert
Screws (2)
Retaining
Clips
Figure 7
Tie
Here