Service manual

Test the 700T Operation
Use the following instructions to test the full speed and incline range of the
treadmill and to check the belt for proper operation.
! CAUTION During this procedure STAY OFF THE RUNNING BELT!
Stand with your feet on the side platforms.
1. Without anyone on the treadmill, plug the power cord into the front end
of the treadmill and into a power outlet from a grounded, dedicated
circuit, and 115 VAC, 60 Hz and 20 amps, or 230 VAC, 50 Hz, and 15
amps, or 208/220 VAC, 60 Hz and 15 amps.
2. Locate the on/off (I/O) power switch on the front of the treadmill. Toggle
it to the on position (I).
3. The control panel will light up and continuously display the prompt
message PRESS START when the treadmill is in Dormant Mode with
the on/off power switch turned on (I) and the treadmill power cord
plugged in. (Cybex recommends that the treadmill be unplugged or the
On/Off (I/O) power switch turned Off (O) when it is not in use.)
NOTE: Cybex recommends that the treadmill be unplugged or the on/off
(I/O) power switch turned off (O) when it is not in use.
4. Press the START/ENTER key to enter the Program Select Mode.
5. Upon entering the Program Select Mode, the center window lights to
prompt the user to press the appropriate keys to change the program
and/or level. The display shows “- + PROGRAM and v
^
LEVEL.” After
five seconds, the PRESS START message will begin to flash.
6. Press START/ENTER to accept the default program, P1 Manual Mode.
The treadmill begins a countdown in both display windows, “3...2...1,”
and sounds a tone for each count. After it reaches one (1), the treadmill
gives a steady tone, and then starts accelerating the belt to reach 1 mph
(1.6 kph).
7. The left display will flash the incline set point of 0% grade and the right
display will flash the speed set point of 1.0 until the treadmill reaches
these settings, at which time the values will stop flashing and remain
steadily illuminated.
8. Press and hold down the SPEED + key until the treadmill reaches a
speed of approximately 4 mph (6.4 kph), as indicated on the display.
Cybex 700T Treadmill Owner’s Manual
Page 5-9
Front Pages
3 Operation
Quick Operation Guide . . . . 3-1
Detailed Operation Guide . . 3-1
Stopping the Treadmill. . . . . 3-3
Control During Operation . . 3-4
Data Readouts. . . . . . . . . . . 3-5
Selecting Programs &
Options. . . . . . . . . . . . . . . 3-6
Displaying Heart Rate . . . . . 3-6
Use of Programs . . . . . . . . . 3-7
P1 - Manual Mode. . . . . . . . 3-7
P2 - Speed Challenge. . . . . 3-8
P3 - Cardiovascular
Program . . . . . . . . . . . . . 3-10
P4 - Weight Loss Program 3-12
P5 - Fitness Test Program. 3-14
P6 - Saved Program . . . . . 3-16
Workout Tips . . . . . . . . . . . 3-17
4 Preventive Maintenance
Regular Maintenance
Activities. . . . . . . . . . . . . . 4-1
Cleaning Your Treadmill. . . . 4-1
Running Belt Maintenance . 4-2
Other Preventive
Maintenance . . . . . . . . . . . 4-6
Service Schedule . . . . . . . . . 4-7
Log Sheet. . . . . . . . . . . . . . . 4-8
5 Setup & Assembly
Quick Setup . . . . . . . . . . . . 5-1
Choosing & Preparing a Site 5-1
Electrical Power
Requirements . . . . . . . . . . 5-3
Unpacking . . . . . . . . . . . . . . 5-3
Assembling the Treadmill . . . 5-4
Testing the 700T Operation. 5-9
Setting Operation Options. 5-10
6 Customer Service
Contacting Service. . . . . . . . 6-1
Serial Number & Voltage. . . . 6-1
Warranty. . . . . . . . . . . . . . . . 6-1
Return Material Authorization
(RMA) . . . . . . . . . . . . . . . . 6-4
Damaged Parts. . . . . . . . . . . 6-4
Ordering Parts . . . . . . . . . . . 6-5
7 Service
Service Instruction . . . . . . . . 7-1
Motor Brushes. . . . . . . . . . . 7-1
Motor Current & Voltage . . . 7-4
Running Belt & Deck. . . . . . 7-7
Drive Belt. . . . . . . . . . . . . . . 7-9
Front Roller . . . . . . . . . . . . . 7-9
Rear Roller. . . . . . . . . . . . . 7-10
Error Codes. . . . . . . . . . . . 7-11
Diagnostic Tests . . . . . . . . 7-14
Parts List . . . . . . . . . . . . . . 7-21
Exploded View . . . . . . . . . . 7-25
700T Schematic . . . . . . . . . 7-26