Service manual

Cybex 700T Treadmill Owner’s Manual
Page 7-19
Front Pages
About this Manual . . . . . . . . . . i
3 Operation
Quick Operation Guide . . . . 3-1
Detailed Operation Guide . . 3-1
Stopping the Treadmill. . . . . 3-3
Control During Operation . . 3-4
Data Readouts. . . . . . . . . . . 3-5
Selecting Programs &
Options. . . . . . . . . . . . . . . 3-6
Displaying Heart Rate . . . . . 3-6
Use of Programs . . . . . . . . . 3-7
P1 - Manual Mode. . . . . . . . 3-7
P2 - Speed Challenge . . . . . 3-8
P3 - Cardiovascular
Program . . . . . . . . . . . . . 3-10
P4 - Weight Loss Program 3-12
P5 - Fitness Test Program. 3-14
P6 - Saved Program . . . . . 3-16
Workout Tips . . . . . . . . . . . 3-17
4
Preventive Maintenance
Regular Maintenance
Activities . . . . . . . . . . . . . . 4-1
Cleaning Your Treadmill . . . . 4-1
Running Belt Maintenance . 4-2
Other Preventive
Maintenance . . . . . . . . . . . 4-6
Service Schedule . . . . . . . . . 4-7
Log Sheet . . . . . . . . . . . . . . . 4-8
5
Setup & Assembly
Quick Setup . . . . . . . . . . . . 5-1
Choosing & Preparing a Site 5-1
Electrical Power
Requirements . . . . . . . . . . 5-3
Unpacking . . . . . . . . . . . . . . 5-3
Assembling the Treadmill . . . 5-4
Testing the 700T Operation . 5-9
Setting Operation Options. 5-10
6 Customer Service
Contacting Service . . . . . . . . 6-1
Serial Number & Voltage. . . . 6-1
Warranty . . . . . . . . . . . . . . . . 6-1
Return Material Authorization
(RMA) . . . . . . . . . . . . . . . . 6-4
Damaged Parts. . . . . . . . . . . 6-4
Ordering Parts . . . . . . . . . . . 6-5
7 Service
Service Instruction . . . . . . . . 7-1
Motor Brushes. . . . . . . . . . . 7-1
Motor Current & Voltage . . . 7-4
Running Belt & Deck . . . . . . 7-7
Drive Belt . . . . . . . . . . . . . . . 7-9
Front Roller . . . . . . . . . . . . . 7-9
Rear Roller. . . . . . . . . . . . . 7-10
Error Codes . . . . . . . . . . . . 7-11
Diagnostic Tests . . . . . . . . 7-14
Parts List . . . . . . . . . . . . . . 7-21
Exploded View . . . . . . . . . . 7-25
700T Schematic . . . . . . . . . 7-26
sequence displayed in the left window.
Example 1:
d11 4 6
Example 1 shows that error code number 6 was generated four error messages
ago.
ERROR CODE NUMBERS
1: No speed signal at startup
2: Excessive current draw
3: Loss of speed signal
4: No frequency lock
5: Elevation error
6: Overspeed
7: Loss of NOVRAM
Only one error code from the log can be displayed at any time. To scroll
through the Error Log, use either the speed or the elevation keys.
Treadmill errors that compromise safety will cause the treadmill to become
inoperative. These require that power be cycled off, then on again to resume
use. If the errors recur, the treadmill will again be inoperative and will require
repair by an authorized Cybex service technician.
Active keys during this test (hold keys for two seconds):
START/ENTER will save settings and advance you to the next diagnostic
test.
STOP will exit and return you to the mode you were in before entering
Diagnostic Tests.
SHIFT backs you up one step in the diagnostics test menu.
The - + keys cycle you through the Error codes.
The v
^
keys cycle you through the Error codes.
d12: LOG Clear (Error Log & Service Reminder clear switch)
This test allows you to clear (erase) all the error codes in the Error Log and/or
to clear (turn off) a Service Reminder. In this test, the left window displays the
error set message (ErrS), and the right window shows the Service Reminder set
message (nnS).
Example 1:
ErrS nnS
To clear the Error Log, press the
^
key, and the left window will display the
error clear command (Err C).