Cybex Eagle® Row Owner’s and Service Manual Strength Systems Part Number 11030-999 J www.cybexinternational.
Cybex Eagle® Row Owner’s and Service Manual Strength Systems Part Number 11030-999 J Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. Eagle® and its mark are registered trademarks of Cybex International, Inc. DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the contents of this manual.
Table of Contents 1 Safety Safety. . . . . . . . . . . . . . . . . . . . . . . . . . Warning/Caution Decals . . . . . . . . . . . Regular Maintenance Activities . . . . . . Using Proper Form . . . . . . . . . . . . . . . 1-1 1-2 1-5 1-5 2 Exercises General Exercise Guidelines . . . . . . . . 2-1 3 Customer Service Contacting Service. . . . . . . . . . . . . . . . Ordering parts . . . . . . . . . . . . . . . . . . . Return Material Authorization (RMA). . Damaged Parts . . . . . . . . . . . . . . . . . .
Cybex Eagle 11030 Row Owner’s Manual 1 - Safety Safety Read the Owner’s Manual carefully before assembling, servicing or using the equipment. It is the responsibility of the facility owner and/or owner of the equipment to instruct users on proper operation of the equipment and review all labels. WARNING: Serious injury could occur if these safety precautions are not observed: User Safety Precautions • Obtain a medical exam prior to beginning an exercise program.
Cybex Eagle 11030 Row Owner’s Manual • Make sure that each machine is set up and operated on a solid level surface. Do not install equipment on an uneven surface. • Make sure that all users are properly trained on how to use the equipment. • Make sure there is enough room for safe access and operation of the equipment. • Perform regular maintenance checks on the equipment. Also pay close attention to all areas most susceptible to wear, including (but not limited to) cables, pulleys, belts and grips.
Cybex Eagle 11030 Row Owner’s Manual 3. Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when anchoring the equipment to the floor. 4. Due to the wide variation of flooring on which machines may be anchored or installed, verify anchoring method and anchoring fasteners with a qualified and licensed contractor. 5. A minimum pull out force of 220 lbs/100 kgs is required for each anchor position.. 6. Do not use machine until it is properly anchored.
Cybex Eagle 11030 Row Owner’s Manual A CAUTION Personal injury may occur. Keep away from moving parts to avoid injury. 4000Y316-4 B C CAUTION Seat may fall if improperly engaged. Verify seat is secure before exercising to avoid injury.
Cybex Eagle 11030 Row Owner’s Manual Row - 11030 B B B A B C DESCRIPTION PART NO. A. Warning Decal ..............4605-381-4 B. Caution Decal ...............4000Y316-4 C. Caution Decal ...............
Cybex Eagle 11030 Row Owner’s Manual Regular Maintenance Activities Preventative maintenance activities must be performed to maintain normal operation of your equipment. Keeping a log sheet of all maintenance actions will assist you in staying current with all preventative maintenance activities. The preventative maintenance actions are described in detail in Chapter 5. Briefly, they include: Daily 1. Clean upholstery. Weekly 1. Inspect all nuts and bolts for looseness. Tighten as required. 2.
Cybex Eagle 11030 Row Owner’s Manual 2 - Exercise MUSCLES USED Intended Use The intended use of this equipment is to aid or improve general physical fitness and exercise. For Commercial use. Instructions Read and understand all instructions and warnings prior to using this machine. See Chapter 1, Safety in the Eagle Owner’s Manual or consult with floor staff.
Cybex Eagle 11030 Row Owner’s Manual Set Up 1. Adjust chest pad to allow comfortable reach of handles. 2. Grasp handles with hands in front of and level with the shoulders. Movement 1. Pull the handles towards you until your elbows are at your sides.
Cybex Eagle 11030 Row Owner’s Manual 3 - Customer Service Contacting Service Hours of phone service are Monday through Friday from 8:30 to 6:00 p.m. Eastern Standard Time. For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239. For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax 508-533-5183. Find information on the web at www.cybexintl.com or by e-mail at techhelp@cybexintl.com. Ordering Parts Fax order to 508-533-5183.
Cybex Eagle 11030 Row Owner’s Manual 1. Call the Customer Service Hot Line listed above for the return of any item that is defective. 2. Provide the technician with a detailed description of the problem you are having or the defect in the item you wish to return. 3. Provide the model and serial number of your Cybex equipment. 4. At Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for evaluation and repair or replacement.
Cybex Eagle 11030 Row Owner’s Manual 4 - Assembly TOOLS REQUIRED • • • • • • • 7/32” Allen wrench 3/4” Allen wrench 9/16” Wrench External snap ring pliers Phillips screwdriver Medium weight automotive engine oil Torque Wrench NOTE: Two people will be required for this procedure. NOTE: It is the responsibility of the facility owner/owner of the equipment to ensure that there is appropriate clearance around each machine to allow for safe use and passage. 1.
Cybex Eagle 11030 Row Owner’s Manual C. Cut shipping tie securing top weight. Cam D. Rotate cam and disconnect weight stack belt from cam (by loosening the two set screws on the belt clamp with a 7/32” Allen wrench). See Figure 1. E. Locate the pulley bracket that is located near the cam. See Figure 2. Set Screws Figure 1 Hex Nut/Washer Pulley Bracket F. Remove bolt, washer and hex nut securing the pulley to the pulley bracket. G. Remove pulley from pulley bracket. H.
Cybex Eagle 11030 Row Owner’s Manual O. With an assistant, carefully remove the six BHSCS securing the two halves of the frame. See Figure 6. BHSCS (qty 6) P. Carefully lay the taller half of the frame down on the floor until you are ready to move it. Q. Carefully move each half through the door-way to the desired location. Again, lay the taller half of the frame down on the floor until you are ready to reattach the two halves. R.
Cybex Eagle 11030 Row Owner’s Manual 6. Install the weight stack. Frame A. Note how the increment weights are installed. Upper snap ring B. With an assistant holding the increment weights, move the adjusting knob to 0 lbs. and remove all six increment weights (three each side). Wave washer C. Using an external snap ring pliers, remove the upper snap ring from one of the guide rods and carefully lower the guide rod. See Figure 10. Guide rod Lower snap ring Figure 10 D.
Cybex Eagle 11030 Row Owner’s Manual 7. Belt Routing. A. Verify belt is routed through top of pulley bracket and then route end of belt down to the top weight. B. Carefully lift top weight and verify that the position of the belt clamp (on the top weight) is aligned properly with the top pulley bracket (on the machine). See Figure 12. C. Slide belt through slot in belt clamp. D. Verify belt and insert are installed properly, as shown in Figure 13A.
Cybex Eagle 11030 Row Owner’s Manual B. Install the top two screws securing the back shroud. See Figure 17. C. Install the three Phillips head screws securing the top (back) shroud. See Figure 18. 9. Install weight plate decals. Screw NOTE: You have the option to use pounds, kilograms or both. A. Slowly and carefully peel off back side of decal. See Figure 19. NOTE: When peeling off back cover, make sure that the decals remain attached to the front sticker. Figure 17 B.
Cybex Eagle 11030 Row Owner’s Manual Chapter 5 - Maintenance All preventive maintenance activities must be performed on a regular basis. Performing routine preventive maintenance actions can aid in providing safe, trouble-free operation of all Cybex Strength Systems equipment. NOTE: Cybex is not responsible for performing regular inspection and maintenance actions for your machines. Instruct all personnel in equipment inspection and maintenance actions and also in accident reporting/recording.
Cybex Eagle 11030 Row Owner’s Manual More Difficult Stains • Dampen a soft white cloth with a solution of 10% household bleach (sodium hypochlorite), 90% water. Rub gently. Rinse with a water dampened cloth to remove bleach concentration. • The same procedure can be used with full strength household bleach, if necessary. • Allow bleach to puddle on the affected area or apply with a soaked cloth for approximately 30 minutes. Rinse with a water dampened cloth to remove any remaining bleach concentration.
Cybex Eagle 11030 Row Owner’s Manual 4. Guidelines for cleaning front panel: • Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing. • Follow up the application with warm water rinse. • Don’t use abrasives or high alkaline cleaners. • Don’t leave cleaners on for long periods, wash immediately. • Don’t apply cleaners in direct sunlight or at elevated temperatures. • Don’t use scrapers, squeegees or razors. • Don’t clean with gasoline.
Cybex Eagle 11030 Row Owner’s Manual Weekly Procedures 1. Check all nuts and bolts for looseness. Tighten as required. 2. Inspect all belts (entire length) for any non-uniformity and wear.
Cybex Eagle 11030 Row Owner’s Manual 3. Some machines use cables in addition to belts. Inspect all cables for wear or damage and proper tension. When inspecting cables, run your fingers on the cable, paying particular attention to bends in the cable and attachment points. Replace all worn cables immediately. The following conditions may indicate a worn cable: • A tear or crack in the cable sheath that exposes the cable. See Figure 1. Figure 1 • A kink in the cable. See Figure 2.
Cybex Eagle 11030 Row Owner’s Manual 4. Inspect bars and handles for wear, paying particular attention to tab area connecting points. Replace all worn handles immediately. 5. Inspect snap links for proper latching (indicates wear). Replace all worn snap links immediately. 6. Inspect for loose or worn grips. Replace all loose or worn grips immediately. 7. Inspect all labeling for readability. This includes instructional placards, warning and caution decals. Replace all worn labeling immediately. 8.
Cybex Eagle 11030 Row Owner’s Manual Environment Static Electricity - Depending upon where you live, you may experience dry air, causing a common experience of static electricity. This may be especially true in the winter time. You may notice a static build-up just by walking across a carpet and then touching a metal object. The same can hold true while working out on your unit. You may experience a shock due to the build-up of static electricity on your body and the discharge path of the unit.
Cybex Eagle 11030 Row Owner’s Manual Maintenance Page 5-8
Cybex Eagle 11030 Row Owner’s Manual 6 - Service Please refer to the next several pages for parts lists, exploded-view diagrams. NOTE: All inspections and repairs must be performed by trained service personnel only. Cybex will void warranty if non-Cybex replacement parts are used.
Cybex Eagle 11030 Row Owner’s Manual This page intentionally left blank Service Page 6-2
Cybex Eagle 11030 Row Owner’s Manual ROW PRODUCT NO. 11030 A E A D P H F A C M N L A I B G NOTE: See exploded-view diagram for location of J (serial number decal), K (belt) and O (Cybex Decal). A. B. C. D. E. F. G. H. DESCRIPTION PART NO. Caution Decal .................... Caution Decal .................... Warning Decal ................... Placard Decal .................... Eagle Plaque ...................... Chest Pad .......................... Seat Pad ............................ Grip.......
Cybex Eagle 11030 Row Owner’s Manual ITEM QTY PART NO. DESCRIPTION ITEM QTY PART NO.
83 71 51 1 83 94 42 83 42 82 79 EAGLE ROW MAIN ASSEMBLY DETAIL 3 4 72 8 36 5 1 70 70 39 79 72 17 42 76 79 62 89 66 72 79 23 47 50 69 72 66 72 35 87 53 79 48 72 72 72 44 95 96 45 36 79 98 99 72 97 39 83 81 81 79 86 97 103 104 Cybex Eagle 11030 Row Owner’s Manual Service Page 6-5
Service Page 6-6 65 18 65 58 58 80 58 56 84 18 13 43 9 58 70 84 13 70 88 63 12 18 80 56 58 57 37 18 67 38 92 78 58 88 70 58 58 57 ARM ASSEMBLY DETAIL 18 65 67 38 92 37 78 43 70 58 58 65 63 12 18 9 58 57 57 Cybex Eagle 11030 Row Owner’s Manual
74 40 26 30 31 75 75 27 75 26 29 60 90 22 52 73 109 24 75 101 110 SHROUD AND GUIDE ROD ASSEMBLY DETAIL 75 74 75 41 19 24 74 30 32 25 29 75 102 75 100 28 Cybex Eagle 11030 Row Owner’s Manual Service Page 6-7
Cybex Eagle Row Owner’s Manual EAGLE ROW FRAME ASSEMBLY DETAIL 52 68 70 68 68 52 70 6 63 105 68 64 70 107 62 106 14 61 70 79 SERIAL NUMBER 72 108 15 62 54 70 70 4 14 70 93 57 21 85 70 77 16 57 74 7 Service Page 6-8
72 79 72 23 35 104 46 97 80 59 72 69 79 59 76 10 72 53 69 76 34 80 55 59 97 11 35 79 2 SEAT ASSEMBLY DETAIL 59 8 72 72 79 50 Cybex Eagle Row Owner’s Manual Service Page 6-9
Cybex Eagle Row Owner’s Manual BELT AND CABLE ROUTING DETAIL 4 60 5 .54 0.8 1 02 04 06 0.5 4 0.4 5 0.3 6 0.2 7 0.1 8 0.0 9 0.9 9 0.8 01 0.7 11 08 0.6 21 0.
Cybex Eagle Row Owner’s Manual ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 QTY 1 1 2 2 1 1 1 1 1 1 1 4 2 1 1 2 PART NO. 11040-366 11040-367 11040-369 11040-370 11040-427 11040-426 11040-424 11040-416 11040-425 BH030207 4700-251 BR030209 BR030220 HP016820 HP266765 HS720004 DESCRIPTION Top Weight Assembly, Molded Hub, Molded Rod, Linkage Pin Rod Stem Cover Plate Cover, Top Weight Knob Pin, Weight Selector Lifting Post 15 External Retaining Ring .188 Internal Retaining Ring 1.250 Cotter Pin .125 X 1.
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 www.cybexinternational.com • Techhelp@cybexintl.
