Cybex Total Access Seated Leg Curl Owner’s and Service Manual Strength Systems Part Number 14061-999-4 D www.cybexinternational.
Cybex Total Access Seated Leg Curl Owner’s and Service Manual Strength Systems Part Number 14061-999-4 D Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. VR3® and its mark are registered trademarks of Cybex International,Inc. DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the contents of this manual.
Table of Contents Front Pages Table of Contents . . . . . . . . . . . . . . . . i Declaration of Conformity . . . . . . . . . ii 1 Safety Safety . . . . . . . . . . . . . . . . . . . . . . . . . Safety Guidlines and Practices . . . . . Warning/Caution Decals . . . . . . . . . . Regular Maintenance Activities . . . . . Using Proper Form . . . . . . . . . . . . . . 1-1 1-2 1-3 1-6 1-6 2 Exercises Intended Use . . . . . . . . . . . . . . . . . . . 2-1 Instructions . . . . . . . . . . . . . . . . . . .
Page ii
This page intentionally left blank.
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual 1 - Safety Safety Read the Owner’s Manual carefully before assembling, servicing or using the equipment. It is the responsibility of the facility owner and/or owner of the equipment to instruct users on proper operation of the equipment and review all labels. WARNING: Serious injury could occur if these safety precautions are not observed: User Safety Precautions • Obtain a medical exam prior to beginning an exercise program.
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual • Make sure that each machine is set up and operated on a solid level surface. Do not install equipment on an uneven surface. • Make sure that all users are properly trained on how to use the equipment. • Make sure there is enough room for safe access and operation of the equipment. • Perform regular maintenance checks on the equipment.
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual 3. Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when anchoring the equipment to the floor. 4. Due to the wide variation of flooring on which machines may be anchored or installed, verify anchoring method and anchoring fasteners with a qualified and licensed contractor. 5. A minimum pull out force of 220 lbs/100 kgs is required for each anchor position.. 6. Do not use machine until it is properly anchored.
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual A CAUTION B C CAUTION D CAUTION Personal injury may occur. Keep away from moving parts to avoid injury.
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual Seated Leg Curl 14061 C C D C B C A Description Part No. A. Warning Label....................4605-381-4 B. Caution Decal.....................4520-362-4 C. Caution Decal.....................8500-026-4 D. Caution Decal.....................
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual Regular Maintenance Activities Preventative maintenance activities must be performed to maintain normal operation of your equipment. Keeping a log sheet of all maintenance actions will assist you in staying current with all preventative maintenance activities. The preventative maintenance actions are described in detail in Chapter 5. Briefly, they include: Daily 1. Clean upholstery. Weekly 1. Inspect all nuts and bolts for looseness.
Cybex Total Access Owner’s Manual 2 - Exercise MUSCLES USED Intended Use The intended use of this equipment is to aid or improve general physical fitness and exercise. For commercial use. Instruction Read and understand all instructions and warnings prior to using this machine. See Chapter 1, Safety, in the Owner’s Manual or consult with floor staff. START Hamstrings FINISH NOTE: Motion Developed: Knee Flexion NOTE: Do not turn knob when weight stack is elevated.
Cybex Total Access Owner’s Manual Set Up - Consult floor staff if assistance is required. 1. Adjust back pad so when seated, knees align with machine’s axis of rotation. 2. Adjust leg pad comfortably behind ankles 3. Lower thigh pad to a snug position. 4. Grasp handles and stabilize body Movement 1. Pull down and back against ankle pad until feet are below seat.
Cybex Total Access Owner’s Manual 3 - Customer Service Contacting Service Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m. Eastern Standard Time. For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239. For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax 508-533-5183. Find information on the web at www.eCybex.com or by e-mail at techhelp@cybexintl.com. Ordering Parts Fax your order to 508-533-5183.
Cybex Total Access Owner’s Manual Return Material Authorization (RMA) The Return Material Authorization (RMA) system outlines the procedures to follow when returning material for placement, repair or credit. The system assures that returned materials are properly handled and analyzed. Follow the following procedures carefully. Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will request a RMA from Cybex, if applicable.
Cybex Total Access Owner’s Manual Damaged Parts Materials damaged in shipment should not be returned for credit. Shipping damages are the responsibility of the carrier (UPS, Federal Express, trucking companies, etc.) Apparent Damage - Upon receipt of your shipment, check all items carefully. Any damage seen with a visual check must be noted on the freight bill and signed by the carrier’s agent. Failure to do so will result in the carriers refusal to honor your damage claim.
Cybex Total Access Owner’s Manual This page intentionally left blank Customer Service Page 3-4
Cybex Total Access Owner’s Manual 4 - Assembly TOOLS REQUIRED • • • • • 7/32” Allen wrench 1/8” Allen wrench Medium weight automotive engine oil Torque wrench 3/4” Wrench NOTE: Two people will be required for this procedure. NOTE: It is the responsibility of the facility owner/owner of the equipment to ensure that there is appropriate clearance around each machine to allow for safe use and passage. NOTE: Refer to chapter 6 for reference diagrams. 1.
Cybex Total Access Owner’s Manual E. Slide spring loaded top guide rod cap down guide rod until guide rod cap is clear of frame. NOTE: Top guide rod cap is spring loaded. F. Slowly release grasp of guide rod cap. NOTE: Guide rod cap contains a compression spring that will fly if grasp is not released slowly. G. Remove guide rod cap and spring and set aside. H. Repeat steps 5F-5H for other rod guide. I. Carefully lean guide rods slightly outward, away from machine to clear pulley.
Cybex Total Access Owner’s Manual 6. Belt Routing. Correct belt routing A. Verify belt is routed through top of pulley bracket and then route end of belt down to the top weight. Wrong belt routing Insert Insert Belt Belt B. Carefully lift top weight and verify that the position of the belt clamp (on the top weight) is aligned properly with the top pulley bracket. Stem Stem C. Slide belt through slot in belt clamp. Figure 2A D. Verify belt and insert are installed properly, as shown in Figure 2A.
Cybex Total Access Owner’s Manual NOTE: It is important that you perform regular inspection and maintenance activities on your equipment. See the CYBEX Owner’s Manual for inspection and maintenance activities. If you do not have a CYBEX Owner’s Manual or if you have any questions or concerns, call CYBEX Customer Relations at 888-462-9239. 9. Verify proper operation 10. Securely anchor machine to the floor. A. Securely anchor machine to the floor using the anchor holes provided in each machine.
Cybex Total Access Owner’s Manual Chapter 5 - Maintenance All preventive maintenance activities must be performed on a regular basis. Performing routine preventive maintenance actions can aid in providing safe, trouble-free operation of all Cybex Strength Systems equipment. NOTE: Cybex is not responsible for performing regular inspection and maintenance actions for your machines. Instruct all personnel in equipment inspection and maintenance actions and also in accident reporting/recording.
Cybex Total Access Owner’s Manual More Difficult Stains • Dampen a soft white cloth with a solution of 10% household bleach (sodium hypochlorite), 90% water. Rub gently. Rinse with a water dampened cloth to remove bleach concentration. • The same procedure can be used with full strength household bleach, if necessary. • Allow bleach to puddle on the affected area or apply with a soaked cloth for approximately 30 minutes. Rinse with a water dampened cloth to remove any remaining bleach concentration.
Cybex Total Access Owner’s Manual 4. Guidelines for cleaning front panel: • Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing. • Follow up the application with warm water rinse. • Don’t use abrasives or high alkaline cleaners. • Don’t leave cleaners on for long periods, wash immediately. • Don’t apply cleaners in direct sunlight or at elevated temperatures. • Don’t use scrapers, squeegees or razors. • Don’t clean with gasoline. 5.
Cybex Total Access Owner’s Manual Weekly Procedures 1. Check all nuts and bolts for looseness. Tighten as required. 2. Inspect all belts (entire length) for any non-uniformity and wear.
Cybex Total Access Owner’s Manual 3. Some machines use cables in addition to belts. Inspect all cables for wear or damage and proper tension. When inspecting cables, run your fingers on the cable, paying particular attention to bends in the cable and attachment points. Replace all worn cables immediately. The following conditions may indicate a worn cable: • A tear or crack in the cable sheath that exposes the cable. See Figure 1 Figure 1 • A kink in the cable. See Figure 2.
Cybex Total Access Owner’s Manual 4. Inspect bars and handles for wear, paying particular attention to tab area connecting points. Replace all worn handles immediately. 5. Inspect snap links for proper latching (indicates wear). Replace all worn snap links immediately. 6. Inspect for loose or worn grips. Replace all loose or worn grips immediately. 7. Inspect all labeling for readability. This includes instructional placards, warning and caution decals. Replace all worn labeling immediately. 8.
Cybex Total Access Owner’s Manual Environment Static Electricity - Depending upon where you live, you may experience dry air, causing a common experience of static electricity. This may be especially true in the winter time. You may notice a static build-up just by walking across a carpet and then touching a metal object. The same can hold true while working out on your unit. You may experience a shock due to the build-up of static electricity on your body and the discharge path of the unit.
Cybex Total Access Owner’s Manual This page intentionally left blank Maintenance Page 5-8
Cybex Total Access Owner’s Manual 6 - Service Please refer to the next several pages for parts lists, exploded-view diagrams and cable and belt routing diagrams. NOTE: All inspections and repairs must be performed by trained service personnel only. Cybex will void warranty if non-Cybex replacement parts are used.
Cybex Total Access Owner’s Manual This page intentionally left blank Service Page 6-2
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual SEATED LEG CURL PRODUCT NO. 14061 A F C E C L H,I G C P J K B D C M O NOTE: See exploded-view diagram for location of N (serial number decal). DESCRIPTION A. B. C. D. E. F. G. H. DESCRIPTION PART NO. Placard Decal .................... 14061-598-4 Warning Decal.................... 4605-381-4 Caution Decal ................... 8500-026-4 Caution Decal .................... 4520-362-4 Caution Decal ....................
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual ITEM QTY PART NO.
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual ITEM QTY PART NO.
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual 14061 VR3 TA MAIN ASSEMBLY 47 74 88 74 95 12 80 88 47 66 49 80 66 49 95 2 73 127 95 117 18 95 116 51 97 59 97 93 Torque Set Screws 300-350 in/lbs 94 116 117 18 18 118 93 50 112 112 48 27 67 Serial Number Decal Service Page 6-4 48
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual SEATED LEG CURL SEAT ASSEMBLY 79 119 123 22 124 79 70 55 22 87 129 79 27 58 24 56 70 131 70 57 23 23 98 25 79 106 129 63 53 79 24 70 106 70 100 108 108 100 82 10 83 77 43 70 54 86 25 79 25 70 22 79 107 109 107 79 79 36 109 88 88 41 106 118 81 107 106 81 Service Page 6-5
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual SEATED LEG CURL PANEL ASSEMBLY 17 96 96 15 93 16 96 96 85 85 120 85 96 93 17 14 96 85 85 85 96 85 13 96 93 85 45 126 85 128 96 122 93 130 19 85 13 45 126 96 Service Page 6-6
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual SEATED LEG CURL RLD AND THIGH PAD ASSEMBLY 116 117 38 91 62 108 46 103 99 87 104 2 71 103 89 89 Torque Set Screws 300-350 in/lbs 97 71 60 125 89 91 43 90 87 77 26 1 65 43 79 4 102 90 32 77 7 3 103 61 79 11 100 3 100 106 33 102 40 111 109 29 65 20 108 105 21 106 31 1 99 100 69 81 81 72 5 6 89 68 89 115 79 37 124 28 88 124 110 91 72 87 99 92 39 110 87 69 27 44 99 110 8 34 35
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual Top Weight Assembly (Light Stack and Heavy Stack Configurations) ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 QTY 1 1 2 2 1 1 1 1 1 1 1 4 2 1 1 2 PART NO.
Cybex Total Access 14061 Seated Leg Curl Owner’s Manual Belt Routing Assembly Detail 73 73 Service Page 6-9
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 www.cybexinternational.com • Techhelp@cybexintl.