Canopy Installation Manual

ManualsBrandsCyclone ManualsAppliancesDesigner Collection Series 42 Inch Wall Mount Ducted Hood

Self-Cleaning Range Hoods

Models:

Installation and Operation Instructions

Please read all instructions before installing and operating.

All wiring and installation must be in accordance with CEC, NEC and local electrical codes.

READ AND SAVE THESE INSTRUCTIONS

Wall Mount and Island Range Hoods

SC(B)300, SC(B)500, HC400, AW00, SC(B)301,

SC(B)501, HC401, AW01, SC(B)502, ALW02,

SC(B)503, SC510, ALW10, SC(B)513, HC413,

SC(B)514, HC414, ALW14, AW14, AB14, SCB516,

SCB316, SC(B)519, SC(B)319, SI(B)323, SI(B)520,

SI(B)521, SI(B)522, SI(B)523, SI530, SI531, SI532

SCB711, SC712, SC(B)715, ALW15, SCB717,

SCB718, SC720, SC(B)322, SC(B)722, ALW22

Summary of content (15 pages)

PAGE 1
Self-Cleaning Range Hoods Wall Mount and Island Range Hoods Models: SC(B)300, SC(B)500, HC400, AW00, SC(B)301, SC(B)501, HC401, AW01, SC(B)502, ALW02, SC(B)503, SC510, ALW10, SC(B)513, HC413, SC(B)514, HC414, ALW14, AW14, AB14, SCB516, SCB316, SC(B)519, SC(B)319, SI(B)323, SI(B)520, SI(B)521, SI(B)522, SI(B)523, SI530, SI531, SI532 SCB711, SC712, SC(B)715, ALW15, SCB717, SCB718, SC720, SC(B)322, SC(B)722, ALW22 Installation and Operation Instructions Please read all instructions before installing and oper
PAGE 2
Cyclone Canopy Installation - English
PAGE 3
IMPORTANT SAFETY INSTRUCTIONS Please read all instructions before installing and operating. Model specifications may vary, please check our website for the most up to date specifications. WARNING • • • This appliance must be installed by a qualified technician. The manufacturer declines all responsibilities in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product.
PAGE 4
CONTENTS 4 Important Safety Instructions 3 Damage Inspection 5 Ducting 5 Mounting Heights and Clearance 6 Wiring Installation 6 Wall Mount Installation - Tools and Materials Required 7 Wall Mount Installation - Parts Supplied 7 Wall Mount Hood Installation 8 Island Installation - Tools and Materials Required 9 Island Installation - Parts Supplied 9 Island Hood Installation 10 Canopy Hoods Specifications 12 Troubleshooting 13 Control Panel 14 Maintenance 14 Cycl
PAGE 5
DAMAGE INSPECTION • • • • Please fully inspect unit for damage before installation. If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. If the unit is damaged by the installer (if other than the customer), repair of replacement must be made by arrangement between customer and installer.
PAGE 6
MOUNTING HEIGHTS AND CLEARANCE WARNING • The hood should be installed at 28” minimum above the cooking surface. If pairing your range hood with a gas stove minimum mounting height must be 30” above the cooking surface. Minimum mount height between range top to hood bottom should be no less than 28” for electric or ceramic stoves, and no less than 30” for gas stoves. The maximum mount height should be no more than 36”. The hood must be installed at the correct mounting height.
PAGE 7
WALL MOUNT INSTALLATION - TOOLS AND MATERIALS REQUIRED • • • • • • • Electrical drill or ratchet driver ½” drill bit for drilling pilot holes 1 ¼” drill bit for drilling electrical wiring access hole (if applicable) Phillips screwdriver #2 or driver bit Wire stripper or cutter Tape measure Aluminum foil tape and/or duct tape • • • • • • • Electrical supplies for wiring (i.e.
PAGE 8
WALL MOUNT HOOD INSTALLATION Install the Wall Mount Hood 1. Measure from range top to hood bottom and use a leveler to mark line A (28” minimum from range top for electric/ ceramic stoves, 30” minimum from range top for gas stoves). 2. Place and mark center line C/L. 3. Use the hood fan as template to find the mounting screws position. Keep the hood bottom centered and level on line A. Mark the position of the two mounting screws (Figure 1).
PAGE 9
ISLAND INSTALLATION - TOOLS AND MATERIALS REQUIRED • • • • • • • Electrical drill or ratchet driver ½” drill bit for drilling pilot holes 1 ¼” drill bit for drilling electrical wiring access hole (if applicable) Phillips screwdriver #2 or driver bit Wire stripper or cutter Tape measure Aluminum foil tape and/or duct tape • • • • • • • Electrical supplies for wiring (i.e.
PAGE 10
ISLAND HOOD INSTALLATION Install Mounting Bracket CAUTION • At least two installers are required due to the weight and size of the hood. This hood should be installed to a finished ceiling. Turn off power circuit at the service panel before wiring this unit. All electrical work must be done by a qualified electrician in accordance with all applicable codes and standards. This range hood must be properly grounded. • • • WARNING • 1. 2.
PAGE 11
3. 4. Position the ceiling mounting plate in such a way that one of the sides with three screw holes faces the front of the hood. Secure mounting bracket to the ceiling using four wood screws. Ensure that screws are driven into the center of the framing for maximum strength. Assemble two upper side brackets to the ceiling mounting bracket using six mounting screws (three per bracket) (Figure 5 & 6). Use eight screws to mount the lower brackets to the upper brackets.
PAGE 12
CANOPY HOODS SPECIFICATIONS W SC300/SC301/ SC322/ SI323 SIZE 30”/36” MOUNTING WALL SI323 - ISLAND SC500/HC400/ SC501/HC401/ SC502/SC503/ SC510/SC513/ HC413/SC514/ HC414/ 30”/36” AW00/AW01/ ALW02/ALW10/ AW14/AB14 SC707/SC712/ SC717/SC718/ SC720/SC722/ ALW22/SC727/ SC771 SCB500/SCB501/ SCB514/SC711/ SC715/ALW15 SI520/SI521/SI522/ SI523/SI530/SI531 SC500/SC514 24”/30”/36” SC500/SC514 24”/30”/36” 30”/36” 30”/36” SC718 - 36” 30”/36” SCB500/SCB514 24”/30”/36” 36” SI523 - 30”/36” WALL WALL WALL
PAGE 13
TROUBLESHOOTING For additional service inquiries, contact Cyclone servicing department at 1-888-293-5662 or Service@CycloneRangeHoods.com ISSUE CAUSE Unit doesn’t work 1. after installation. 1. Ensure power is ON for the circuit breaker and unit. 2. The power line and the cable locking connector 2. are not connected properly. Check the power connection with the unit is connected properly. 3. The switch button seized. 3. Loosen the switch mounting screws from back of the switch. 4.
PAGE 14
CONTROL PANEL To Engage Time-Delay Off Functions: Timer 1. 2. LED Screen Light Turn the machine on at any speed To activate the timer after cooking, press the timer button once. The screen light will begin flashing with a default of 3 minutes before turning off. To set the timer, press the lowest fan speed setting to toggle the desired timer up to 9 minutes.
PAGE 15
CYCLONE RANGE HOODS LIMITED WARRANTY Cyclone Range Hoods Inc. (hereunder called “The Company”) provides a warranty that its products are free from defects in workmanship and materials for a period of two (2) years from the date of purchase. This warranty includes in-home service (where applicable) for the first year and workshop service for the second year. During that time period, The Company will, at the Company’s option, repair or replace without charge any parts or complete unit found to be defective.