Self-Cleaning Range Hoods Installation and Operating Instructions Please read all instructions before installing and operating. All wiring and installation must be in accordance with CEC, NEC and local electrical codes. Attention : All Cyclone range hoods require a 6’’ducting. You must use no less than 6 ‘‘ ducting for your warranty to be active. If you use any size ducting less than mentioned above your warranty is automatically voided. ONLY CYS1000R may use a 4’’ ducting.
READ AND SAVE THESE INSTRUCTIONS CONTENTS Pg. 3) Ducting Pg. 4) Mount Heights & Clearance Pg. 5) Canopy Range Hood Installation Pg. 6) Electrical Grounding Pg. 7) Specifications Pg. 8) Control Panel Pg. 9) Island Range Hood Installation instructions Pg. 10) Mounting the Island Range Hood Pg. 11) Diagram Pg. 14) Island Surface Maintenance/Filters/ Replacing Light Bulbs Pg. 15) Cyclone Warranty All rights reserved to North America Range Hoods Inc. 110 Silver Star Blvd.
READ AND SAVE THESE INSTRUCTIONS Caution: FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZORDOUS OR EXPLOSIVE MATERIALS OR VAPORS. This appliance must be installed by a qualified technician. The manufacturer declines all responsibility in case of failure to adhere to safety standards. Ensure that exhausted air not directed into flue that is uses for venting fumes from other appliances. Warning To reduce the risk of fire, electric shock, or injury to persons, observe the following: 1. 2. 3. 4.
BEFORE INSTALLING THE HOOD 1. For the most efficient airflow exhaust use a straight run or as few elbows as possible. Vent unit to the outside only. 2. Two people are required for installation Ducting Always use rigid type metal ducts. Flexible ducts can restrict airflow by more than 50%. 6” round ductwork must be used to maintain maximum air flow efficiency with the 550 CFM motor. Reduce the number of transitions and turns as much as possible.
Hood installation height above cook top is the user’s preference. The lower the hood is above the cook top the more efficient it will be in drawing out cooking odours, grease and smoke. THE HOOD SHALL BE INSTALLED AT 28” MINIMUM TO 36” ABOVE THE COUNTERTOP. Check your ceiling height and the hood height maximum before you select your hood. Mount Heights and Clearance Minimum mount height between range top to hood bottom should be no less than 28”. The maximum mount height should be no more than 36”.
Installation: 1. 2. 3. 4. 5. 6. 7. 8. Determine the necessary height for the conduit and cut a 1-1/4” hole. Run wires through the hole according to local codes and ordinances. Use caulking to seal all openings. Do not turn the power on until completion of installation. Find studs behind drywall by tapping wall or using a stud finder. Make sure there is a stud or that the wall is strong enough to support the weight of the Canopy fan.
Electrical Grounding Instructions This appliance is fitted with an electrical junction box with 3 wires, one of which (green/yellow) serves to ground the appliance. To protect you against electric shock the green and yellow wire must be connected to the grounding wire in your home electrical system and it must not be cut or removed under any circumstances. Failure to do so may result in death or injury to persons.
Air Flow Volume 550 CFM Electrical Connections 120V, 60Hz Power Consumption 200 Watts Fan Speed / # Of Motor(s) 1550 RPM / One motor Colours Stainless Steel Venting SC-500. SC-501, SC-502 SC-503, SC-510 Dimensions SC-500 2 Width: 24”/30”/36” Height Max: 25 25.88” Depth: 1 20” SC-501/ SI-521 30” / 36” 34.4”/35.2” 20” / 24” SI-521, SI-522, SI-520, SI-523, SI530, SI-531 SC-502/ SI-522 30”/36” 44”/44” 20”/24” SC-503 SC-510 30”/36” 40” 20” 36” 28” 20” SI-523/ DI-531 36” 47.
SURFACE MAINTENANCE Always switch off power and unplug before cleaning and maintenance. Clean with warm soapy water and clean cloth. Do not use corrosive or abrasive detergent or steel wool pads that can scratch the surface of the machine. Use non-abrasive stainless steel polish to buff out the luster and grain. Scrub lightly. The stainless steel filters trap residue and grease from cooking.
Island Hoods installation instructions: Warning: For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow National electrical codes or prevailing local codes and ordinances. Electrical Supply This appliance requires a 120V 60 Hz electrical supply, and must be connected to an individual properly grounded branch circuit, protected by a 15 or 20-ampere circuit breaker or time delay fuse.
All rights reserved to North America Range Hoods Inc. 110 Silver Star Blvd., Unit 105, Scarborough, Ontario, Canada, M1V5A2 TEL: 416.293.0933 FAX: 416.293.4793 www.cyclonerangehoods.
Installing island range hood: 1. Remove kitchen ceiling tiles etc. and locate/create ducting hole. 2. Locate wooden beams adjacent to ducting hole. 3. Insert and attach two wooden pieces forming a square frame around the ducting hole with the already existing beams. 4. With included screws attach the adjustable white metal support to the wooden frame. 5. Attach duct through the support into the ducting hole in the ceiling. 6.
All rights reserved to North America Range Hoods Inc. 110 Silver Star Blvd., Unit 105, Scarborough, Ontario, Canada, M1V5A2 TEL: 416.293.0933 FAX: 416.293.4793 www.cyclonerangehoods.
SURFACE MAINTENANCE FOR ISLAND RANGE HOOD Always switch off power and unplug before cleaning and maintenance. Clean with warm soapy water and clean cloth. Do not use corrosive or abrasive detergent or steel wool pads that can scratch the surface of the machine. Use non-abrasive stainless steel polish to buff out the luster and grain. Scrub lightly. The stainless steel filters trap residue and grease from cooking.
Cyclone Range Hood Limited Warranty North American Range Hoods Inc. (hereunder called “The Company”) provides a warranty that its products are free from defects in workmanship and materials for a period of two (2) year from the date of purchase. During that time period, The Company will, at no charge, replace at the Company’s option, any parts or complete unit found to be defective. Further, the warranty for the motor extends for an additional three (3) years, with labour costs extra.
