DELUXE REMOTE ALARM USER INSTRUCTIONS CYCL PS SECURITY SYSTEMS PROUDLY AUSTRALIAN
CYCL PS SECURITY SYSTEMS THIS CARD SHOULD NOT BE LEFT IN YOUR VEHICLE. IT MUST BE KEPT IN A SAFE SECURE PLACE.
Contents Page Introduction Operations 5 6 ! Remote controls ! Arming and Disarming ! PIN Override Procedure 10 ! Programmable Options ! Program Options Table ! Options Descriptions ! Changing PIN Code 6 6 ! Battery Replacement Specifications Optional Features ! Arm/Disarm Siren Confirmation 6 ! Silent Arming 7 ! Automatic Arming 7 ! Dome Light Function 7 ! Panic Feature 8 ! Open Door Warning 8 ! Immobilisation 8 ! Alarm Protection Zones 9 ! Diagnostics 9 ! Emergency Override 9 ! Central Locking !
-4-
CYCLOPS PARALYSER 385 ENGINE IMMOBILISER CYCL PS SECURITY SYSTEMS Introduction Congratulations on having one of the world's most advanced alarm and engine immobilisers installed in your vehicle. The CYCLOPS P385 meets Australian Standards AS/NZS 4601 & AS/NZS3749. The P385 uses high security, high reliability circuitry to disable your car’s engine. The alarm system uses sensors and independent switches to protect the entry points to the vehicle.
OPERATIONS REMOTE CONTROLS LED The P385 is supplied with two rolling code remote controls. Each time a button is pressed, the code rolls to a new code. Each code is never used twice. A small green Light Emitting Diode (LED) will light when a remote control button is pressed. ARMING AND DISARMING MAIN BUTTON SECONDARY BUTTON KEYRING To arm or disarm the system, press the main button on the remote control. The vehicle’s indicators will confirm a valid remote operation.
SILENT ARMING The arm/disarm confirmation chirps can be suspended for one operation by momentarily pressing the secondary button before pressing the main button. The chirp will re-enable upon the next operation. The siren can be permanently cancelled by changing option #13 (see page 11) AUTOMATIC ARMING The P385 will automatically disable the engine 40 seconds after the ignition switch is turned off.
PANIC FEATURE (Car Location) The P385 can be commanded “panic” for 30 seconds if the main button is pressed for more than 2 seconds. The panic feature will sound the siren and flash the indicators. To cancel the Panic Feature, momentarily press the main button once more. The panic feature is available only while the system is armed. OPEN DOOR WARNING If any connected door is detected as being open while arming, the P385 will flash the indicators and chirp the siren 8 times.
ALARM PROTECTION ZONES The P385 protects the vehicle by monitoring all door, bonnet and boot switches, as well as “listening” for the sound of breaking glass. For convertibles and softtop cars additional sensors can be installed to provide movement detection. DIAGNOSTICS When any circuit triggers the P385, the number of the zone responsible will be recorded in the system memory. The number is flashed back through the indicators and status LED when the P385 is next disarmed.
PIN OVER-RIDE PROCEDURE To illustrate the PIN over-ride procedure we DUST CAP will assume a PIN of 4,3,2,1. 1. Turn the lock on the back of the siren to KEY disable the sound. LOCK 2. If indicators are still flashing, allow the system to reset with all doors closed. 3. Turn ignition switch to ON position, the SIREN status LED will remain lit. SWITCH SIREN OFF 4. Turn ignition switch to the ACC position and count the LED flashes. 5. Turn ignition switch ON when the 4th flash has extinguished. 6.
PROGRAMMABLE OPTIONS The P385 includes 9 programmable options which alter the system functions to comply with the user’s preferences and vehicle special needs. Changing an option setting is as simple as ! Switch the ignition key ON a certain number times (this number corresponds to the option number). ! Press the remote control after the prompt from the vehicle’s indicators. After the remote press the indicators will flash either once or three times to show the result of the option change.
PROGRAMMABLE OPTION DESCRIPTIONS Option #3** the Anti Hijack feature locks the car doors when the ignition is switched on, except when a connected door is open. The anti hijack feature unlocks the doors when the ignition is switched off (when driver has reached destination). The feature is disabled if the dome light illumination is extended by a vehicle timing circuit. ! Option #7 programming remote isn't strictly an optional feature. This feature is used if a spare remote is purchased.
PROGRAMMABLE OPTION DESCRIPTIONS cont’ Option #13** sets the system to always arm/disarm in silent mode. The standard indicator flashes will accompany each arm/disarm command, but the siren will remain silent. ! Option #15** enables the auto-relock feature. The doors will automatically re-lock when the vehicle has been disarmed by remote control and the doors remain closed for more than 120 seconds. ! Option #17** is used to extend the time length of the central locking pulses.
CHANGING PIN CODE To alter the PIN code of the system, follow the standard option change procedure; select option #19. ! The vehicle indicators will flash twice to inform you that the system is ready to accept the new PIN. The “time-out” is set to two seconds. If the programming has not begun before then, the system will drop-out of programming mode. ! Enter the new digits by momentarily pressing the main button on a valid remote control. The vehicle indicators will flash in response to each press.
BATTERY REPLACEMENT Using a flat head screwdriver to carefully CASE TOP MEMBRANE PCB separate the two body housings taking CASE BOTTOM care not to disturb the circuit board. Remove the old batteries whilst paying attention to the orientation of the positive and negative terminals. Insert new KEYRING batteries in identical fashion to the original and re-assemble REMOVE BATTERIES IN THIS DIRECTION remote. Test remote control by pressing main button.
SPECIFICATIONS Manufactured by Model Number Standards met Supply voltage Current consumption Country of manufacture RF Transmission Freq Dynamco Pty Ltd. P385. Both AS/NZS 4601 and 3749 +9VDC - 15VDC. less than 20mA (while armed). China (in Dynamco’s ISO-9002 facility). 433MHz OPTIONAL FEATURES All optional features require additional connections. Many require additional hardware as well. Each feature is described within the next pages.
BOOT RELEASE Press the second button on the remote control and keep it depressed until the boot releases*. This will take about three seconds. A successful boot release signal will disarm the alarm and flash the vehicle indicators four times. This function can only operate if the vehicle is equipped with an electrical boot release. ANTI HIJACK Two seconds after the ignition is switch to the ON position, the P385 will lock the cars doors.
WARRANTY The Dynamco range of Cyclops Security Systems is covered by an extensive two year warranty (parts & accessories one year). In the unlikely event of a faulty system Dynamco will either replace or repair the system at no cost during the 2 year period. The warranty does allow for the following conditions ~ Subject to the conditions stated below, Dynamco Pty Ltd warranty the product to be free from manufacturing defects and faulty material within the warranty period stated.
WARRANTY REGISTRATION PURCHASED FROM OWNER’S NAME TYPE OF VEHICLE VEHICLE REGO MODEL OF UNIT P.I.N DATE OF MANUFACTURE DATE OF INSTALL’ WARRANTY PERIOD CONTROL MODULE SIREN & REMOTES INSTALLER’S NAME AFTER HOURS EMERGENCY PHONE -19- . . . . CYCL PS SECURITY SYSTEMS . . . . . . .
-20-