CMSI-8H8HS DR A FT 8×8 HDMI Matrix Operation Manual
FT A DR
DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document.
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product.
CONTENTS 1. Introduction �������������������������������������������� 1 2. Applications ������������������������������������������� 1 3. Package Contents �������������������������������� 1 4. System Requirements ���������������������������� 1 5. Features �������������������������������������������������� 2 6. Operation Controls and Functions ������� 3 6.1 Front Panel ����������������������������������������3 FT 6.2 Rear Panel �����������������������������������������4 6.
1. INTRODUCTION The 8×8 HDMI Matrix supports the transmission of Video (up to 1080p Full HD/1920×1200@60 Hz) with multichannel digital audio from up to eight high definition sources to up to eight HDMI outputs and allowing any source to be independently displayed on any monitor. Also, the unit can be controlled via IR, RS-232, Telnet or the front panel button controls. 2.
5. FEATURES • HDMI, HDCP 1.
6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel MENU POWER 8X8 HDMI MATRIX CMSI-8H8HS 1 2 A 1 B 2 C 3 D 4 OUT E 5 F 6 G 7 H 8 IN LOCK 3 4 5 6 setting. FT 1 LCM: Displays the setting information of each input and output 2 POWER: Press this button to power the device on/off. The LED will illuminate green when the power is on, red when it is in 'Standby' mode. 3 LOCK: Press this button to lock all the buttons on the panel; press A again to unlock.
6.2 Rear Panel 3 5 A HDMI Out CONTROL B HDMI Out C HDMI Out D HDMI Out E HDMI Out F HDMI Out G HDMI Out H HDMI Out IR-In V+ GND 1 HDMI In 1 2 GND 3 4 1 2 V+ GND Service RS-232 3 2 HDMI In 3 HDMI In 4 HDMI In 4 5 HDMI In 6 HDMI In 7 HDMI In DC 24V 8 HDMI In 6 7 FT 1 CONTROL: This port is the link for Telnet control, connect to an active Ethernet link with an RJ45 terminated cable (for further details, please refer to section 6.7).
6.3 Side Panel 1 1 FFan Ventilator: These are air ventilation areas, DO NOT block these FT areas or cover it with any object. Please allow adequate space around the unit for air circulation. 6.4 Remote Control A 1 POWER: Press this button to 1 switch on the device or set it to standby mode. 2 IN: Input ports selection 1~8. DR 3 OUT: Output ports selection A~H.
6.
6.7 6.6 RS-232 and Telnet Commands Description A1~A8 Switch Output A to 1~8 B1~B8 Switch Output B to 1~8 C1~C8 Switch Output C to 1~8 D1~D8 Switch Output D to 1~8 E1~E8 Switch Output E to 1~8 F1~F8 Switch Output F to 1~8 G1~G8 Switch Output G to 1~8 H1~H8 FT Command Switch Output H to 1~8 ABCE…1~ABCD…8 Switch Output ABCD… to 1~8 at the same time Setting IP. SubNet.
6.8 6.7 Telnet Control Before attempting to use the telnet control, please ensure that both the Matrix (via the 'LAN /CONTROL' port) and the PC/Laptop are connected to active networks. Note: Please do not connect both the Matrix and the PC/Laptop with a single CAT5e/6 cable as it will not access the telnet function. To access the telnet control in Windows 7, click on the 'Start' menu and type "cmd" in the Search field then press enter.
Once in the command line interface (CLI) type "telnet", a space, then the IP address of the unit you wish to control, a space and "23", then hit enter. Note: The IP address of the Matrix can be displayed on the device's LCM monitor by pressing the Menu button twice. DR A FT This will bring us into the device which we wish to control. Type "HELP" to list the available commands. Type “IPCONFIG” To show all IP configurations.
7.
8. SPECIFICATIONS Video Bandwidth 255 MHZ/6.75 GBPS Input Ports 8×HDMI, 1×RS-232, 1×IR Receiver, 1×Mini USB Type B (For firmware update only), 1×RJ-45 Output Ports 8×HDMI HDMI Input Cable Distance 15m/8-bit, 10m/12-bit HDMI Output Cable Distance 15m/8-bit ,15m/12-bit ESD Protection Human-body Model: FT ± 8kV (Air-gap discharge) ± 4kV (Contact discharge) Power Supply 24 V/6.
9.
FT A DR CYPRESS TECHNOLOGY CO., LTD Home page: http://www.cypress.com.