CLUX-H2SDI HDMI to 3G SDI Dual-Output Converter Operation Manual CLUX-H2SDI
Disclaimers The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document.
Safety Precautions Please read all instructions before attempting to unpack or install or operate this equipment, and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
Table of Contents 1. 2. 3. 4. 5. 6. 7. Introduction................................................................................... 1 Applications.................................................................................. 1 Package Contents....................................................................... 1 System Requirements................................................................... 1 Features.........................................................................................
1. Introduction The HDMI™ to 3G SDI converter allows HDMI signals to be shown on SDI displays while ensuring high bit rates of 2.970 Gbit/s to give you high resolution signal without any loss. For professionals this means that it is now easier to convert your high def HDMI signal with audio to 3G SDI for long distance transmission and display your work on two 3G SDI display. Also, a 2CH L/R audio input allows DVI signal with 2CH audio to be converted to SDI in order to be shown on SDI displays.
• • • Connect with other units (SDI to HDMI) to extend your signal over long distances Choose between a selectable EDID and recordable EDID Supports signal transmission distances of up to 300M for SD signals, 200M for HD signals and 100M for 3G signals Note: Cable tested with Belden 1694A. Operating distances may vary if used w ith another type of cable 6. Specifications SDI Transmission Frequency Bandwidth Input Output Input Support Timing Rates 2.970 Gbit/s and 2.970/1.
. Operation Controls and Functions 7.1 Front Panel 3 4 6 7 1 ① 2 5 8 9 EDID Update button: Use this function only when the image does not display after trying to switch the EDID/HD/3G EDID swtich. EDID procedures as below. DVD Player HDMI CLUX-H2SDI SDI SDI Monitor A. Please make sure the DVD is set on “auto mode” in output timing's setting. If the image display properly, stop using this function but if no image display after the connection. go to step B.
CLUX-H2SDI 1.Switch the dip switch to EDID update postion 2.Pressed on the EDID update button consistently (HDMI Cable) HDMI TV/Monitor C. Connect the HDMI monitor or TV to the input port of CLUX-H2SDI and then set the dip switch to EDID update position. Press the EDID update button consistently until the Video Lock LED illuminate. In this step the device will updating the monitor/TV’s EDID to replace the default setting. DVD Player HDMI CLUX-H2SDI SDI SDI Monitor D.
7.2 Rear Panel 1 1. 2 3 4 5 HDMI In: This slot is to connect with the input source equipment such as DVD or Blue-Ray player with connection cable for input video and audio signal transmitting. Or it can also be connect with DVI source equipment for video signal transmitting. 2. Audio Switch: Switch this switch to allowing the audio to be send from HDMI or R/L. 3. Audio Switch: Switching this switch allowing the audio to be send from HDMI or R/L. 4.
8. LED Signal Chart System Operation LED Signal Status No.
3. EDID switch mode / Default EDID setting: 3G 1080p@60 HD 1080i@60 Update / SD 720p@60 4. Due to HDMI’s default timing are mainly set on 480p but SDI does not support such timing therefore, it is possible that the image will not dis play. To avoid such event, it is suggested to set the source input equip ment’s output timing on the “AUTO mode” for the source equipment to send the EDID native timing of the display. 5. Only No. 4,5,12,16,20 & 24 needs to do EDID update.
9.
A Acronyms Acronym Complete Term 3G Bandwidth 2.
10
11
CYPRESS TECHNOLOGY CO., LTD. Home page: http://www.cypress.com.