User manual

ManualsBrandsCypress ManualsMusical equipmentCSC-1200T

(1). Introduction

Congratulations on your purchase of the Cypress Video Scaler CSC-200P.

Our professional

Video Scaler products have been serving the industry for many years.

In addition to Video Scalers, Cypress offers a full line of high quality PC multimedia,

Standards Converters, DV-to-Analog Converters,Video Mixer, Time Base Correctors,

and Video Processors. Please visit www.cypress.com.tw to learn more details about

these products. This manual includes operation information on the CSC-200P model.

Please read this to become familiar with the CSC-200P. and keep the manual for

possible reference in the future.

Cypress's CSC-200P is designed to convert Composite S-Video and YCbCr signals

to a variety of computer and HDTV resolutions. It handles video input from TV systems

NTSC, PAL and SECAM TV standards. Cypress CSC-200P has many great features to

enhance performance and is ideal for use in professional large screen presentation.

(2). Features

1. Video inputs are de-interlaced and scaled up to output resolution as below

* PC output : 640x 480, 800x 600 (SVGA), 1024 x768 (XGA), 1280 x 1024(SXGA),

* HDTV output: 852 x 480p, 852 x 576p, 1280 x 720p,1920 x 1080i

2. Automatically accommodates input video systems of NTSC 3.58, PAL and SECAM.

3. High performance adaptive 3D Comb filter Y/C separator.

4. Per-pixel motion compensated deinterlacing algorithms to produce artifact-free

progressive scan video signal.

5. Built in Adaptive film mode 3:2 pull-down provides clear and crisp de-interlacing

of video originating from 24 fps film,such as DVD movies.

6. Frame rate conversion from 50Hz up to 60Hz (PAL), or 60Hz up to 60Hz(NTSC)

7. Vertical temporal filter(VT) removes jaggy and other de-interlacing artifacts from

normal video.

8. OSD menu with adjustable control on Color, Sharpness, Brightness,

Contrast and Tint(NTSC).

9. Built-in DCTI/DLTI circuit for color/luminance transient improvement.

10. The PC loop-through allows for easy change between video and PC source.

11. Last memory for all adjustments.

(3). Checking the Package Contents

The following items are contained in shipping carton:

1. Video Scaler Unit

2. DC adaptor

3. VGA Cable-HD 15 to HD 15 x 1

4. HD-15 D-Sub to YPbPr 3-RCA Cable

5. 1BNC-1BNC video cable x 1

6. S-Video Input Cable

7. YCbCr 3-RCA- to 3-RCA cable x 1

8. User Manual

9. Remote Control

10. 2 x 4A battery

(7). RS-232 Control of the CSC-200P Video Scaler

* Command / Response codes of RS-232 transmission:

Command Response Description

"[POWER1]" "[POWER1]" power on(normal)

"[POWER0]" "[POWER0]" power off(standby)

"[IN0]" "[IN0] Composite video input

"[IN1]" "[IN1]" S video input

"[IN2]" "[IN2]" Y PB PR/Y CB CR input

"[IN3]" "[IN3]" PC input

"[OUTPC0]" "[OUTPC0]" PC VGA output

"[OUTPC1]" "[OUTPC1]" PC SVGA output

"[OUTPC2]" "[OUTPC2]" PC XGA output

"[OUTPC3]" "[OUTPC3]" PC SXGA output

"[OUTHD0]" "[OUTHD0]" HD 480P output

"[OUTHD1]" "[OUTHD1]" HD 576P output

"[OUTHD2]" "[OUTHD2]" HD 720P output

"[OUTHD3]" "[OUTHD3]" HD 1080i output

"[OSD0]" "[OSD0]" OSD off

"[OSD1]" "[OSD1]" OSD on

"[DISPLAY0]" "[DISPLAY0]" Display off

"[DISPLAY1]" "[DISPLAY1]" Display on

"[IR0]" "[IR0]" IR sensor off

"[IR1]" "[IR1]" IR sensor on

"[PANEL0]" "[PANEL0]" Fromt panel lockout on

"[PANEL1]" "[PANEL1]" Fromt panel lockout off

"[COMB0]" "[COMB0]" 3D enhance off

"[COMB1]" "[COMB1]" 3D enhance on

"[DNR0]" "[DNR0]" Digital NR off

"[DNR1]" "[DNR1]" Digital NR on

"[ASPECT0]" "[ASPECT0]" Aspect standard

"[ASPECT1]" "[ASPECT1]" Aspect 16:9

"[ASPECT2]" "[ASPECT2]" Aspect 4:3

"[CONTRASTx]" "[CONTRASTx]" Contrast　 x=0~63

"[BRIGHTx]" "[BRIGHTx]" Brightness x=0~63

"[COLORx]" "[COLORx]" Color x=0~63

"[HUEx]" "[HUEx]" Tint x=0~63

"[DETAILx]" "[DETAILx]" Sharpness x=0~63

Video adjustment reset

"[RESET]" "[CONTRAST58]" "[BRIGHT31]" "[COLOR31]"

"[HUE31]" "[DETAIL10]"

Retrive video scaler all status

"[POWER?]" "[IN?]" "[OUTPC?]"

"[OUTHD?]" "[OSD?]" "[DISPLAY?]"

"[STATUS]" "[IR?]" "[PANEL?]" "[COMB?]"

"[DNR?]" "[ASPECT?]" "[CONTRAST?]"

"[BRIGHT?]" "[COLOR?]" "[HUE?]"

"[DETAIL?]"

Home page: http://www.cypress.com.tw

CYPRESS TECHNOLOGY CO., LTD.

(4). Connecting the hardware

Front Panel

2. Picture: Press the button to toggle through picture adjust parameters as follows:

ContrastBright  Color Tint Sharpness Contrast

Contrast: Press  or  to adjust contrast level. The range of adjustment is 0~63.

Factory default value is 58.

Bright: Press  or  to adjust Brightness level. The range of adjustment is 0~63.

Factory default value is 31.

Color: Press  or  to adjust color level. The range of adjustment is 0~63.

Factory default value is 31.

Tint: Press  or  to adjust NTSC Tint level. The range of adjustment is 0~63.

Factory defaults value is 31.

Sharpness: Press  or  to adjust sharpness level.

The range of adjustment is 0~63. Factory defaults at 10.

3.  ,  : Press to toggle through various adjust controls or to alter setting value.

4. IR Sensor: Infrared remote control sensor.

5. Power and LED button: Press once to power on the unit, press again to turn off.

Note:

* Under picture adjust mode, press  and simutaneously will revert the selected

parameter back to factory preset value. Press both buttons for over 5 seconds.

will revert all picture parameters back to their factory preset values.

6. Front Panel Lockout- Under certain circumstances it may be desirable to disable

the front panel controls. For example, to prevent

unauthorized or accidental changes to the setting while the

unit is in use.

To disable the front panel controls use RS-232 to set the

front panel lockout to ON position.

(6). Remote Control

1. Power: Power ON/OFF button.

2. Display: Press the button to enable or disable the on screen display

of the resolution information.

3. C-Video: Press the button to select composite video as input source.

4. S-Video: Press the button to select S-Video as input source.

5. YCbCr: Press the button to select YCbCr as input source.

6. PC: Press the button to select PC input looping through to the output.

7. VGA: Press the button to select 640 x 480 as output resolution.

8. SVGA: Press the button to select 800 x 600 as output resolution.

9. XGA: Press the button to select 1024 x 768 as output resolution.

10. SXGA: Press the button to select 1280 x 1024 as output resolution.

11. 480p: Press the button to select 852 x 480p as output resolution.

12. 576p: Press the button to select 852 x 576p as output resolution.

13. 720p: Press the button to select 1280 x 720p as output resolution.

14. 1080i: Press the button to select 1920 x 1080i (interaced) as output resolution.

15. Aspect ratio: Press the button to switch between standard, 4:3 and

wide (16:9)aspect ratio.

16 IR-Set: When IR sensor is turned off by RS-232, Press this button for

over 15 seconds will turn on the IR sensor.

17. 3D: Press to turn ON/OFF the 3D enhance.

18. NR: Press to turn ON/OFF digital noise reduction.

19. Mode: Same as "mode" button on front panel.

press to toggle through

Source ResolutionOutput

Aspect3D EnhanceDigital NR

Source

20. Picture: Same as picture button on

front panel. Press to toggle

through Contrast Bright

Color  Tint  Sharpness

Contrast

21. Reset: Press this button will revert picture

adjust back to factory preset value.

2 9

(5). Connecting and Installation

(4). Connecting the hardware

Connecting the Video inputs

The video scaler can accept a composite video, an S-Video or a YCbCr input

signal for scaling, as well as a computer signal input that is passed through the unit

when the PC in (Bypass) is selected.

Rear Panel

1 . Composite Video: Use a Composite video cable to connect the composite video

output of the source equipment to the connector labeled

"C-Video" on the back of the Video Scaler.

2 . S-Video: Use a S-Video cable to connect the S-Video output of the source video

equipment to the connector labled " S-Video" on the back of the

Video Scaler.

S-Video provides improved performance over Composite Video and is

recommended over composite.

3 . YCbCr input: Use a 3 RCA-to-3 RCA YCbCr cable to connect the YCbCr output of

the source video equipment to the connectors labled YCbCr on the

back of the video scaler. Please note the plugs' color have to match

with the color of the RCA Jacks. YCbCr component provides the best

picture quality among all three inputs, and should be used whenever

possible.

4 . Computer RGB with H&V Sync: Connect the source computer's VGA output

signal to the HD 15 connector labled "PC In" on the

back of the Video Scaler.

Note: This Computer inputs signal is not sclaed, but is available for pass-through

when the Video Scaler is in the PC In (Bypass) mode.

Connecting the scaled output to your projector, PDP, or LCD Display

5 . The HD-15 D-Sub connector is shared by PC/RGBHV output and HDTV/YPbPr output.

When PC/RGBHV output resoultion (VGA to SXGA) is selected, use the HD-15 to

HD-15 VGA cable to connect the output to the PC input of your display monitor.

When HDTV/YPbPr output (480p, 576p, 720p, 1080i) is selected, use the HD-15 to

YPbPr 3 x RCA cable to connect the output to the YPbPr input of your HDTV display.

Note: Use of wrong cable for your selected output will result in an abnormal picture

on the screen.

6 . DC power jack: 12V 1A DC power input.

2 1

3 4 5 6

INPUT

S-VIDEO

VIDEO

Y Cb Cr

PC IN

RGB/YPbPr

OUTPUT

DC 12V

DC Adaptor

HDTV

Control In