User manual

ManualsBrandsCypress ManualsMusical equipmentCSC-1200T

(7). Specifications

Computer input (Loop thru)

Max computer input resolution

Computer input connector type

Computer input signal level

Video inputs

Video standard

Video input connectors

Scaled output resolutions

Scaled output vertical refresh rates &

Horizontal scan rates

Manual control

IR remote control

Video adjustments

Weight

Dimensions

Power source

RGB with HV Sync

1600 x 1200

HD 15 Female

RGB @ 0.7V, H&V Sync @ TTL

Composite Video @ 1 Vp-p 75 ohm

S-Video @ 1 Vp-p 75 ohm

YCbCr Y : 1 Vpp 75 ohm

CbCr : 0.7 Vp-p 75 ohm

NTSC 3.58, PAL B/D/G/I, SECAM

Composite video on BNC

S-Video on 4-pin Mini-DIN

Component on BNC

Pixels Format Scan

VGA 640 x 480

SVGA 800 x 600

XGA 1024 x 768

SXGA 1280 x 1024

16:9 1280 x 720p (720p)

16:9 1920 x 1080i (1080i)

852 x 480p(480p)

852 x 576p(576p)

Output resolution Vert. (Hz) Hori. (Hz)

59.94

31.469

VGA

SVGA

XGA

SXGA

480p

576p

720P

1080i

60.320 37.880

60.000

48.360

60.020

59.940

59.94

63.981

31.469

31.25

44.995

33.716

Front panel buttons

Yes

Brightness, Contrast, Color Saturation, Tint (NTSC), Sharpness

1 Kgs

204(D)x 154 (W) x 46(H)mm

100~240VAC to DC 12V/1A Desktop switching adaptor

Resolution

RGBHV

YPbPr

Progressive

Interlaced

Progressive

HDTV

Resolution

(4). Connecting the hardware

Front Panel

2. Picture: Press the button to toggle through picture adjust parameters as follows:

ContrastBright  Color Tint Sharpness Contrast

Contrast: Press  or  to adjust contrast level. The range of adjustment is 0~63.

Factory default value is 58.

Bright: Press  or  to adjust Brightness level. The range of adjustment is 0~63.

Factory default value is 31.

Color: Press  or  to adjust color level. The range of adjustment is 0~63.

Factory default value is 31.

Tint: Press  or  to adjust NTSC Tint level. The range of adjustment is 0~63.

Factory defaults value is 31.

Sharpness: Press  or  to adjust sharpness level.

The range of adjustment is 0~63. Factory defaults at 10.

3.  ,  : Press to toggle through various adjust controls or to alter setting value.

4. IR Sensor: Infrared remote control sensor.

5. Power and LED button: Press once to power on the unit, press again to turn off.

Note:

* Under picture adjust mode, press  and simutaneously will revert the selected

parameter back to factory preset value. Press both buttons for over 5 seconds.

will revert all picture parameters back to their factory preset values.

6. Front Panel Lockout- Under certain circumstances it may be desirable to disable

the front panel controls. For example, to prevent

unauthorized or accidental changes to the setting while the

unit is in use.

To disable the front panel controls use RS-232 to set the

front panel lockout to ON position.

(6). Remote Control

1. Power: Power ON/OFF button.

2. Display: Press the button to enable or disable the on screen display

of the resolution information.

3. C-Video: Press the button to select composite video as input source.

4. S-Video: Press the button to select S-Video as input source.

5. YCbCr: Press the button to select YCbCr as input source.

6. PC: Press the button to select PC input looping through to the output.

7. VGA: Press the button to select 640 x 480 as output resolution.

8. SVGA: Press the button to select 800 x 600 as output resolution.

9. XGA: Press the button to select 1024 x 768 as output resolution.

10. SXGA: Press the button to select 1280 x 1024 as output resolution.

11. 480p: Press the button to select 852 x 480p as output resolution.

12. 576p: Press the button to select 852 x 576p as output resolution.

13. 720p: Press the button to select 1280 x 720p as output resolution.

14. 1080i: Press the button to select 1920 x 1080i (interaced) as output resolution.

15. Aspect ratio: Press the button to switch between standard, 4:3 and

wide (16:9)aspect ratio.

16 IR-Set: When IR sensor is turned off by RS-232, Press this button for

over 15 seconds will turn on the IR sensor.

17. 3D: Press to turn ON/OFF the 3D enhance.

18. NR: Press to turn ON/OFF digital noise reduction.

19. Mode: Same as "mode" button on front panel.

press to toggle through

Source ResolutionOutput

Aspect3D EnhanceDigital NR

Source

20. Picture: Same as picture button on

front panel. Press to toggle

through Contrast Bright

Color  Tint  Sharpness

Contrast

21. Reset: Press this button will revert picture

adjust back to factory preset value.

2 9

(5). Connecting and Installation

(4). Connecting the hardware

Connecting the Video inputs

The video scaler can accept a composite video, an S-Video or a YCbCr input

signal for scaling, as well as a computer signal input that is passed through the unit

when the PC in (Bypass) is selected.

Rear Panel

1 . Composite Video: Use a Composite video cable to connect the composite video

output of the source equipment to the connector labeled

"C-Video" on the back of the Video Scaler.

2 . S-Video: Use a S-Video cable to connect the S-Video output of the source video

equipment to the connector labled " S-Video" on the back of the

Video Scaler.

S-Video provides improved performance over Composite Video and is

recommended over composite.

3 . YCbCr input: Use a 3 RCA-to-3 RCA YCbCr cable to connect the YCbCr output of

the source video equipment to the connectors labled YCbCr on the

back of the video scaler. Please note the plugs' color have to match

with the color of the RCA Jacks. YCbCr component provides the best

picture quality among all three inputs, and should be used whenever

possible.

4 . Computer RGB with H&V Sync: Connect the source computer's VGA output

signal to the HD 15 connector labled "PC In" on the

back of the Video Scaler.

Note: This Computer inputs signal is not sclaed, but is available for pass-through

when the Video Scaler is in the PC In (Bypass) mode.

Connecting the scaled output to your projector, PDP, or LCD Display

5 . The HD-15 D-Sub connector is shared by PC/RGBHV output and HDTV/YPbPr output.

When PC/RGBHV output resoultion (VGA to SXGA) is selected, use the HD-15 to

HD-15 VGA cable to connect the output to the PC input of your display monitor.

When HDTV/YPbPr output (480p, 576p, 720p, 1080i) is selected, use the HD-15 to

YPbPr 3 x RCA cable to connect the output to the YPbPr input of your HDTV display.

Note: Use of wrong cable for your selected output will result in an abnormal picture

on the screen.

6 . DC power jack: 12V 1A DC power input.

2 1

3 4 5 6

INPUT

S-VIDEO

VIDEO

Y Cb Cr

PC IN

RGB/YPbPr

OUTPUT

DC 12V

DC Adaptor