CWHDI-TX1 & RX1 Wireless HDMI Transmitter and Receiver Box Operation Manual CWHDI-TX1 & RX1
TABLE OF CONTENTS 1. Introduction................................................................................ 1 2. Features...................................................................................... 1 3. Package Contents.................................................................... 1 4. Operation Controls and Functions.......................................... 2 4.1 Transmitter side................................................................. 2 4.1.1 Front Panel...................
1. Introduction Looking for a way to send an HDMI signal but don’t want to go through the hassle of routing wires through your home or office? Well the wireless HDMI transmitter and receiver boxes with baseband technology and a Wireless High Definition Interface (WHDI) are your answer to a wire free world.
. Operation Controls and Functions 4.1 Transmitter side 4.1.1 Front Panel 4 5 6 Power Link CWHDI-TX1 Transmitter Power 7 HDMI1 HDMI2 HDMI3 Input 1 ID 2 3 ① Power: Press to turn the system on or off. ② Input: Press to select input source (1/2/3). ③ ID: Press transmitter “ID” button and receiver “ID” button for 2 seconds to connect the systems. These systems were already connected before leaving the factory so users don't need to reset them unless the system cannot link up properly.
4.1.2 Rear Panel HDMI IN3 HDMI IN1 HDMI IN2 DC 5V IR BLASTER 1 ① ② ③ 2 3 HDMI 1/2/3 Inputs: Connect each of the input ports to the HDMI output of your source equipment such as DVD/Blu-Ray player or set-top-box. IR Blaster: Connect the IR blaster cable included in the package and place it in front of the source equipment. The IR blaster will transmit the infrared signal to the connected source with the existing remote signal send to this device.
the ID button for more than 10 seconds to switch to a different mode (Broadcast/Unicast). When the LED is green it means switch to Unicast mode and when it is Red, it means switch to Broadcast Mode. The factory default is Unicast mode and it is suggested to use this mode for household use. It is not necessary to press both the transmitter and receiver's ID buttons at the same time. ③ IR sensor. ④ Power: The LED will switch on when power is ON.
5. Remote Control ①. Power: Press to turn the device on or off. ②. ID:Press the transmitters “ID” button and receiver “ID” button for two seconds to connect the system. This system was already connected before leaving the factory so users don't need to reset it again unless the system cannot link up properly. ③. 1~3: Press 1-3 to have your desired input source be displayed on the HDMI output. POWER ID INPUT 1 2 ① ② ③ 3 Transmitter CR-67 6. IR Cable Pin Definitions 6.
7. Connection and Installation 7.1 Unicast mode HDMI Cable HDMI Cable HDMI HDMI PS3 DVD LCD TV Blu-Ray 7.2 Broadcast mode HDMI Cable HDMI LCD TV HDMI HDMI PS3 HDMI HDMI DVD Blu-Ray LCD TV HDMI 7.
8. Specifications Transmit power is configurable up to 60mW (+17dBm) Video Resolutions (Partial List) 480i/p, 576i/p, 720p, 1080i, VGA@60/72, SVGA@60/72, XGA@60/70 and 1080p(24fps/30fps) 4.9 ~ 5.9GHz OFDM MIMO with WHDITH video-modem Frequencies Supported Technology Modulation 20MHz Bandwidth 1.
9. Troubleshooting Situation Check Point 1. Check if the right adaptor is used (5V 2.6A adaptor). Power LED does not turn 2. Make sure all power connectors are correctly on when power is on. plugged in. 3. Push the power button to turn on the device. 1. This is normal if the devices are connecting or in search mode, the LED will slowly turn on when it is doing signal linking, after that is done and when the signal is transmitted and received the LED will be After powering on consistent.
9
CYPRESS TECHNOLOGY CO., LTD. Home page: http://www.cypress.com.
