CWHDI-TX & RX Wireless HDMI Transmitter and Receiver Box Operation Manual CWHDI-TX & RX
TABLE OF CONTENTS 1. Introduction................................................................................ 1 2. Features...................................................................................... 1 3. Package Contents................................................................... 1 4. Operation Controls and Functions.......................................... 2 4.1 Transmitter side................................................................. 2 4.1.1 Front Panel....................
1. Introduction The wireless HDMI transmitter and receiver box are using baseband technology with Wireless High Definition Interface (WHDI) to deliver uncompressed HD video and audio up to 15~30 meters open field, while maintaining superb, wire-equivalent quality and robustness with no latency. The transmitter and receiver side are available with embedded antennas. 2. Features ● ● ● ● ● ● ● ● ● ● ● ● ● Uncompressed HD audio/video wireless transmission at wire-equivalent quality.
. Operation Controls and Functions 4.1 Transmitter side 4.1.1 Front Panel 4 5 6 Power Link CWHDI-TX Transmitter Power 7 HDMI1 HDMI2 HDMI3 Input 1 ID 2 3 ① Power: Press to turn ON/OFF the system. ② Input: Press to select input source (1/2/3). ③ ID: Press transmitter “ID” button and receiver “ID” button for 2 second to pair the system. These systems already paired before exit factory hence, user don't need to reset it again unless the system can’t up link probability.
4.1.2 Rear Panel DC 5V HDMI3 HDMI1 HDMI2 1 2 ① HDMI 1/2/3 Inputs: Connect each of the input ports to the HDMI output of your source equipment such as DVD player or set-top-box. ② Power: Plug the 5V DC power supply into this unit and connect the adaptor to AC wall outlet. 4.2 Receiver side 4.2.1 Front Panel 3 IR CWHDI-RX Receiver 4 5 Power Link Power ID 1 2 ① Power: Press to turn ON/OFF the system. ② ID: Press transmitter “ID” button and receiver “ID” button for 2 second to pair the system.
4.2.2 Rear Panel DC 5V HDMI OUT 1 2 ① HDMI output: Connect the HDMI output to the HDMI input of your display using HDMI cable. ② Power: Plug the 5V DC power supply into this unit and connect the adaptor to AC wall outlet. 5. Remote Control ①. Power: Press to turn ON/OFF the device. ②. ID:Press transmitter “ID” button and receiver “ID” button for 2 second to pair the system.
6.
7. Specifications Radio Power Video resolutions (partial list) Frequencies Supported Modulation Bandwidth Wireless Range Antenna System Features Digital Video Interface Digital Audio Interface System Latency Security Input ports Output port Power Supply Dimensions (mm) Weight(g) Chassis Material Silkscreen Color Operating Temperature Power Consumption Transmit power is configurable up to 63mW (+18dBm) 480i/p, 576i/p, 720p, 1080i, VGA@60/72, SVGA@60/72, XGA@60/70 and 1080p(24fps/30fps) 4.9 ~ 5.
8. Troubleshooting Situation Power LED is not illuminate when power ON. Check Point 1. Check if the right adaptor is used. 5V 2.6A’s adaptor. 2. Check all power connectors are plugged in correctly. 3. Push the power buttons to turn on the devices. 1. After powering on Tx & Rx the Link’s LED is flashing speedily / slowly without image. 2. 3. 1. The Link’s LED is illuminating consistently without image display or unexpected image 2. display. 3. 4. Input’s LED not illuminate. 1.
8
9
CYPRESS TECHNOLOGY CO., LTD. Home page: http://www.cypress.com.