nvSRAM Specification Sheet

CY14B104L, CY14B104N
Document #: 001-07102 Rev. *L Page 4 of 25
Device Operation
The CY14B104L/CY14B104N nvSRAM is made up of two
functional components paired in the same physical cell. They are
an SRAM memory cell and a nonvolatile QuantumTrap cell. The
SRAM memory cell operates as a standard fast static RAM. Data
in the SRAM is transferred to the nonvolatile cell (the STORE
operation), or from the nonvolatile cell to the SRAM (the RECALL
operation). Using this unique architecture, all cells are stored and
recalled in parallel. During the STORE and RECALL operations,
SRAM read and write operations are inhibited. The
CY14B104L/CY14B104N supports infinite reads and writes
similar to a typical SRAM. In addition, it provides infinite RECALL
operations from the nonvolatile cells and up to 200K STORE
operations. See the “Truth Table For SRAM Operations” on
page 15 for a complete description of read and write modes.
SRAM Read
The CY14B104L/CY14B104N performs a read cycle when CE
and OE are LOW and WE and HSB are HIGH. The address
specified on pins A
0-18
or A
0-17
determines which of the 524,288
data bytes or 262,144 words of 16 bits each are accessed. Byte
enables (BHE, BLE) determine which bytes are enabled to the
output, in the case of 16-bit words. When the read is initiated by
an address transition, the outputs are valid after a delay of t
AA
(read cycle 1). If the read is initiated by CE or OE, the outputs
are valid at t
ACE
or at t
DOE
, whichever is later (read cycle 2). The
data output repeatedly responds to address changes within the
t
AA
access time without the need for transitions on any control
input pins. This remains valid until another address change or
until CE or OE is brought HIGH, or WE or HSB is brought LOW.
SRAM Write
A write cycle is performed when CE and WE are LOW and HSB
is HIGH. The address inputs must be stable before entering the
write cycle and must remain stable until CE
or WE goes HIGH at
the end of the cycle. The data on the common IO pins DQ
0–15
are written into the memory if the data is valid t
SD
before the end
of a WE
controlled write or before the end of an CE controlled
write. The Byte Enable inputs (BHE
, BLE) determine which bytes
are written, in the case of 16bit words. It is recommended that
OE
be kept HIGH during the entire write cycle to avoid data bus
contention on common IO lines. If OE
is left LOW, internal
circuitry turns off the output buffers t
HZWE
after WE goes LOW.
AutoStore Operation
The CY14B104L/CY14B104N stores data to the nvSRAM using
one of the following three storage operations: Hardware Store
activated by HSB;
Software Store activated by an address
sequence; AutoStore on device power down. The AutoStore
operation is a unique feature of QuantumTrap technology and is
enabled by default on the CY14B104L/CY14B104N.
During a normal operation, the device draws current from V
CC
to
charge a capacitor connected to the V
CAP
pin. This stored
charge is used by the chip to perform a single STORE operation.
If the voltage on the V
CC
pin drops below V
SWITCH
, the part
automatically disconnects the V
CAP
pin from V
CC
. A STORE
operation is initiated with power provided by the V
CAP
capacitor.
Figure 4 shows the proper connection of the storage capacitor
(V
CAP
) for automatic store operation. Refer to DC Electrical
Characteristics on page 7 for the size of V
CAP
. The voltage on
the V
CAP
pin is driven to V
CC
by a regulator on the chip. A pull
up should be placed on WE
to hold it inactive during power up.
This pull up is only effective if the WE
signal is tri-state during
power up. Many MPU’s will tri-state their controls on power up.
This should be verified when using the pull up. When the
nvSRAM comes out of power-on-recall, the MPU must be active
or the WE
held inactive until the MPU comes out of reset.
To reduce unnecessary nonvolatile stores, AutoStore and
hardware store operations are ignored unless at least one write
operation has taken place since the most recent STORE or
RECALL cycle. Software initiated STORE cycles are performed
regardless of whether a write operation has taken place. The
HSB
signal is monitored by the system to detect if an AutoStore
cycle is in progress.
Figure 4. AutoStore Mode
Hardware STORE Operation
The CY14B104L/CY14B104N provides the HSB
[6]
pin to control
and acknowledge the STORE operations. Use the HSB
pin to
request a hardware STORE cycle. When the HSB
pin is driven
LOW, the CY14B104L/CY14B104N conditionally initiates a
STORE operation after t
DELAY
. An actual STORE cycle only
begins if a write to the SRAM has taken place since the last
STORE or RECALL cycle. The HSB pin also acts as an open
drain driver that is internally driven LOW to indicate a busy
condition when the STORE (initiated by any means) is in
progress.
When HSB
is driven LOW by any means, SRAM read and write
operations that are in progress are given time to complete before
the STORE operation is initiated. After HSB
goes LOW, the
CY14B104L/CY14B104N continues SRAM operations for
t
DELAY
.
During any STORE operation, regardless of how it is initiated,
the CY14B104L/CY14B104N continues to drive the HSB
pin
LOW, releasing it only when the STORE is complete. Upon
completion of the STORE operation, the
CY14B104L/CY14B104N remains disabled until the HSB
pin
returns HIGH. Leave the HSB
unconnected if it is not used.
0.1uF
Vcc
10kOhm
V
CAP
Vcc
WE
V
CAP
V
SS
[+] Feedback