SPX-5000 Series Operations Manual Suprex® Reader Extender - RF Wireless Interface SPX-5601 2.4GHz RPT-5651 2.4GHz Repeater SPX-5521 900 Mhz EXP-2000 SPX-6601 2.
Cypress Suprex SPX-5000 Series Overview This manual covers the operation and setup of the Cypress Suprex RF SPX-5000 series wireless units. Overview: The SPX-5000 series of RF Wireless solutions provides a wireless bridge from Card Readers with gates or door hardware to most access control manufacturers panels. The SPX or Suprex® products include both the remote ( Door/Gate ) unit and the central ( AC Panel ) unit.
Suprex® RF Part Numbers Part Number! Description! ! ! SPX-5521 915 Mhz - extender 10000 ft range RPT-5551 ! Interface ! UPC Wiegand or Clock & Data 816684003387 915 Mhz - repeater 1000 ft range N/A 816684003394 SPX-5601 2.4GHz - extender 2000 ft range Wiegand or Clock & Data 816684003219 SPX-5621 2.4GHz - extender 10000 ft range Wiegand or Clock & Data 816684003189 SPX-6601 2.4GHz - extender 2000 ft range RS-232/RS-485 816684004599 RPT-5651 2.
External connections and DIP Switch Settings 1 - 8 to 16 VDC In 2 - Ground 1- Relay 4 N.O. 2- Relay 4 Com 3 - Relay 4 N.C. 4 - Relay 3 N.O. 5 - Relay 3 Com 6 - Relay 3 N.C. 7 - Ground 8 - Aux out 9 - R2 in 10 - R1 in Status LED 1 - exp (+) 2 - exp (-) 3 - +5 VDC out 4 - Prog Res 4 5 - Prog Res 3 6 - LED In 7 - D1/Data out 8 - D0/Clk out SPX-5000 Central 1 - 8 to 16 VDC In 2 - Ground 1- Relay 2 N.O. 2- Relay 2 Com 3 - Relay 2 N.C. 4 - Relay 1 N.O. 5 - Relay 1 Com 6 - Relay 1 N.C.
Quick Reference For Typical Connections SPX-5000 Series Central DC Power Supply +8 to +16 VDC Ground Diagnostic LED Access Control Panel R1 Input Controls Strike on Remote LED In D1/Data Out D0/Clock Out R1 IN See page 10 for other strike control options SPX-5000 Series Remote DC Power Supply +8 to +16 VDC Ground Diagnostic LED R1 N.O. R1 Com R1 N.C.
Typical RF installation with repeater SPX-5000R (1) ACS SPX-5000C (1) RPT-5X51 Typical RF installation - line of sight ACS SPX-5000R (1) SPX-5000C (1) Typical RF installation expansion modules EXP-2000R (2) EXP-2000R (3) SPX-5000C (1) SPX-5000R (1) ACS EXP-2000C (2) Wiegand connection Card reader EXP-2000C (3) RS-485 multi-drop Control and I/O
Quick Reference For Typical Connections DC Power Supply 8 - 24 VDC Ground Diagnostic LED Access Control Panel TXD RXD DC Power Supply + 5VDC IN 2 NOT USED N.C. COM 1 N.O. Ground Ground SPX-6000 Series Central NOT USED NOT USED - RS-485 + RS-485 RS-232 TX RS-232 RX 8 - 24 VDC Ground Diagnostic LED + 5VDC IN 1 NOT USED N.C. COM 2 N.O.
Cypress Suprex RF Series - Setup and Pre-installation Unpacking: Remove covers from units and check interior for any shipping damage. Remove any packing material if present. Inventory any included parts (depending on model) such as antennas, coax cables etc. Bench Testing: Before installing the units in the field they should be assembled and tested at a convenient “Bench top” location. This will make it easier to verify / change settings and check operation when both units are visible at the same time.
Cypress Suprex RF Series - Indicators and Operating Modes LED Diagnostic Indicator: The LED Diagnostic indicator provides information on the operational status of the unit. If the units are not communicating, viewing the diagnostic indicator LED’s may help to determine the nature of the problem.
Cypress Suprex RF Series - Door Strike and LED I/O To activate the relay on the Remote unit, connect as shown below. These connections can be used to allow the Remote relay to operate a DOOR STRIKE, GATE, or other locking hardware. Refer to following pages in this document for details of each I/O operation and connection. There are two relays available for accessory outputs at the Remote end. Either relay can be used to provide the Door Strike or Gate activation function. This example uses Relay 1.
Cypress Suprex RF Series - Door Strike and LED I/O The Cypress SPX-5000 provides additional data channels to support access control hardware such as door strikes, tamper alarms, request to exit status, etc. These signals are sent to and from the Remote and Central units without the need to run additional wiring. The accessory control I/O use active low inputs. When the inputs are floating (nothing connected) the associated output will be set to a high level.
Cypress Suprex RF Series - Relay Controls Relay 4 N.O Relay 4 Com Relay 4 N.C. Suprex Central Relay 3 N.O. Relay 3 Com Relay 3 N.C. Suprex Central Contact Outputs Contact Outputs Red arrow denotes direction of command signal Suprex Remote Suprex Remote Relay 4 IN Relay 3 IN Input Signal (5Volts DC Maximum) Input Signal (5Volts DC Maximum) Relay 3 functions as an Alarm relay and monitors the condition of the communication link between the Central and Remote units.
SPX-XXXX Application Note Using Supervised Contacts with the SPX-series Extenders Applies to the following products: SPX-5501, SPX-5601, SPX-5521, SPX-5621, SPX-7400, SPX-7410, SPX-7200, SPX-7500, All RIM series products. This application note describes the connections necessary to convey supervised contact status over a Suprex® communication link. The configurations described in this app note should apply to most panels that utilize supervised contacts.
SPX-5000 Setup - Using Expansion Modules Before using EXP-2000 Expansion modules with the SPX-5000 system, it will be necessary to perform a short configuration process. This process determines if the 5000 will utilize expansion modules, and if so, how many will be used with the system. Each SPX-5000 link can support up to 2 expansion modules. SPX-5000 units are shipped in the factory default condition. Factory default units will be setup to function as SPX-5000 units without expansion modules.
Cypress Suprex Wireless Solution with Wiegand expansion modules Door / Parking Gate - Typical SPX-5000R (1) EXP-2000R (2) EXP-2000C (3) ACS EXP-2000R (3) EXP-2000C (2) SPX-5000C (1) Card Reader Wiegand Data RS-485 Link - Multi-drop Control and I/O
Cypress Suprex Series - Wiegand Expansion Module Panel “Central” interface DC Power Supply +8 to +16 VDC Ground EXP(+) EXP(-) Access Control Panel LED In D1/Data Out D0/Clock Out 8 to 16 VDC In Ground 485(+) 485(-) +5 VDC Out Prog Res 4 Prog Res 3 LED Input D1/Data/F2F Out D0/Clock Out * EXP-2000 Central Unit SPX-XXXX Central R1 IN RLY4 N.O. RLY4 Com RLY4 N.C. RLY3 N.O. RLY3 Com RLY3 N.C.
Cypress Suprex Series - Wiegand Expansion Module Reader/Door “Remote” interface DC Power Supply 8 to 16 VDC In Ground EXP (+) EXP (-) SPX-XXXX Remote R1 N.O. R1 Com R1 N.C. LED Out D1/Data In D0/Clock In Card Reader 8 to 16 VDC In Ground 485(+) 485(-) +5 VDC Out RLY4 Input (5V) RLY3 Input (5V) LED Output D1/Data/F2F Input D0/CLK Input * EXP-2000 Remote Unit RLY2 N.O. RLY2 Com RLY2 N.C. RLY1 N.O. RLY1 Com RLY1 N.C.
