1029 ITASCA ST., UNIT C, CHATSWORTH, CA 91311 USA www.cyron.com Media Highlighter® IR Controller HTW1010 Thank you for purchasing CYRON HTW1010 Media Highlighter IR controller. Please follow all the steps to assure proper installation and optimum usage of this device. Read through the instructions before you start your project. Contents _____ Locate all system components. If any of the components are missing or damaged contact CYRON before proceeding with installation.
Keep the controller and wires away from extreme heat, liquids, and moving objects. Low voltage wires can be routed through walls and cabinets as long as proper care is taken to avoid damages. DO NOT modify internal components. Tampering with components and wiring may cause severe damage to your system and will void factory warranty. The CONTROLLER operates on 100% regulated 12 or 24VDC power. The size (wattage) of the power supply depends on the number of lights.
Hardwiring needs ample knowledge of wiring practices. This option should be done by experienced professionals such as electricians or certified custom electronic installers. Please contact CYRON Technical Support for further details. There may be other options available for your project. CYRON experienced Tech Support staff will be happy to help you implement your project. See Appendix A for detailed hardwiring instructions. Operations _____ The HTW1010 remote is designed to be quite intuitive.
Turn-off timer. There are 5 timers of 1, 2, 3, 4 and 5 hours. Each time the button is pressed the lights will flash according to the number of hours. >First press; lights flash once; system turns off in 1 hour. >Second press; lights flash twice; system turns off in 2 hours. >Third press; lights flash three times; system turns off in 3 hours. Same applies for up to 5 hours. Press again to go back to 1 hour.
a DO NOT connect audio input to speaker outputs. Controller will be damaged. Sound sensitivity can be adjusted by pressing the MUSIC button more than once, up to 5 times. Every time the button is pressed there will be a sequence of light flashes, from one flash to 5 flashes. 5 flashes indicates the sound sensitivity is at its maximum. Depending on the type of sound/music and the audio output level, the sensitivity adjustment may not play a big role in light interaction.
mode. Inversely, it can be set to never turn on automatically when the power is restored, also referred to as Auto Off. Use Auto On setting and connect the controller to a timer. Every time the timer comes on the lights will turn on automatically. Same is true if controller is plugged into an outlet that is controlled by a wall switch. Lights can be turned on by the wall switch To set the controller to Auto On: Turn off the lights using the power off button. On the remote press buttons "7, 7, 1".
General Guidance _____ How to make a specific color: It is best to start from a solid color that is close to the color you are trying to get. For example, if you are trying to produce a specific shade of sea green, it is best to start with solid green. If solid green is not one of the colors in memory, one way would be to first press WHITE button. Then, using COLOR DIALS press blue arrow up until blue LEDs turn off. Press red arrow up until the red goes off. You should be left with solid green.
_______________________ ___ Appendix A ___ _______________________ Hardwire Instructions _____ STEP ONE: Open the HTW1000 controller box by removing four screws on the bottom. STEP TWO: Gently take out one of the side circuit boards holding the 6 ports. Lift the main PCB to gain access to the terminal blocks. Be careful not to break any wires connecting the boards. STEP THREE: Take out the housing wire cap. STEP FOUR: Connect wires to the hub following the color code shown in Table One.
positive, two for the negative. This will eliminate extra current being carried over one wire. HTW1000 Terminal Block +12V B G R Wire Color Code HTHUB6 Wires CYRON Ribbon lights Marking / Wire White +12, 24 / Com / Black Black B / Blue Green G / Green Red R / Red STEP FIVE: Place the PCBs back in their positions and close the back cover. Pay close attention to the wires connecting the side PCBs to the main PCB. STEP SIX: Manage the wires. Use zip ties or other means to secure the wires together.
Technical Support _____ CYRON’s goal is 100% customer satisfaction. You may call our technical support line or contact us via email 24/7. techsupport@cyron.com 818-772-1900 x106 In order to continually improve our products we welcome all comments about the product you purchased. Thank You! Warranty _____ Cyron warrants this product against any defects in materials or workmanship for a period of ONE (1) year from the date of purchase.
© 2012 CYRON, Inc.