User´s Guide convert 12A and convert 18A Antes de utilizar el equipo, lea la sección “Precauciones de seguridad” de este manual. Conserve este manual para futuras consultas. Before operating the device, please read the “Safety precautions” section of this manual. Retain this manual for future reference.
CONTENTS SAFETY PRECAUTIONS 3 WARRANTY 4 DECLARATION OF CONFORMITY 5 INTRODUCTION 6 LINE DRAWINGS 7 SPECIFICATIONS 7 8 a 12 CONFIGURATIONS With convert 18A With avant 118A With LX-215A With LX-218CA AMPLIFIER 13 a 15 Description Preliminar Note ON / OFF Overload indicators Overheating Equalisation Low Main Voltage Current consumption Troubleshooting 16 a 21 RIGGING SYSTEM Description AX-convert12 AXS-convert12 TRD-2 y TRD-6 22 APPENDIX Line conections: unbalanced and balanced Manual del U
convert series Precauciones de Seguridad Safety Precautions Cajas acústicas activas / Self-powered loudspeaker enclosures El signo de exclamación dentro de un triángulo indica la existencia de importantes instrucciones de operación y mantenimiento en la documentación que acompaña al producto. Conserve y lea todas estas instrucciones. Siga las advertencias.
GARANTÍA Todos nuestros productos están garantizados por un periodo de 24 meses desde la fecha de compra. Las garantías sólo serán válidas si son por un defecto de fabricación y en ningún caso por un uso incorrecto del producto. Las reparaciones en garantía pueden ser realizadas, exclusivamente, por el fabricante o el servicio de asistencia técnica autorizado. Otros cargos como portes y seguros, son a cargo del comprador en todos los casos.
DECLARACIÓN DE CONFORMIDAD DECLARATION OF CONFORMITY D.A.S. Audio, S.A. C/ Islas Baleares, 24 - 46988 - Pol. Fuente del Jarro - Valencia. España (Spain).
INTRODUCTION The convert powered, multifunction systems combine D.A.S.´s reputation for performance and reliability with the latest technological innovations offering users an unmatched level of versatility. The exceptional characteristics of the onboard amplification, complex waveguide design and digital signal processing provide the output and control required, allowing the convert series to be deployed as a main system or in any number of support applications.
LINE DRAWINGS ALL DIMENSIONS IN MILIMETERS 419 322 convert 12A 582 Front View Rear View Top View Right View 663 convert 18A 555 580 Front View Right View Rear View Top View SPECIFICATIONS MODEL LF Amplifier Power HF Amplifier Power Nominal Amplifier Power Input Type Input Impedance Sensitivity Frequency Range (-10dB) Horizontal Coverage (-6dB) Vertical Coverage Rated Maximum Peak SPL at 1m Transducer/Replacement Parts Enclosure Geometry Enclosure Material Color/Finish Rigging System Splay A
CONFIGURATIONS The convert 12A can be employed alone for voice applications where not a high preassure level is required. For this use, plug the mixer output to the enclosure input. The most frequently use will combine convert12A and convert18A. In this case, plug the mixer output with input signal of convert18A (subwoofer) and then, through the SATELLITE OUTPUT connector, send the signal to convert12A.
CONFIGURATIONS (cont´d) A continuación mostraremos ejemplos, para teatros, de las muchas configuraciones posibles. La convert 12A se puede colgar debajo de las convert 18A para aquellas configuraciones donde se requiera colgar también el subwoofer.
LINK LINK OUT 2 LINK LINK LINK 6 x Convert12A 2 x Avant 118A 1 x DSP-2060 / 2040 LINK LINK LINK CONFIGURATIONS (cont´d) OUT 5 POWER SUPPLY POWER SUPPLY OUT 1 OUT 4 POWER SUPPLY POWER SUPPLY DSP-2060 / 2040 Convert 12 Accessories Rigging frames AX-Convert12 x 2 Speaker cabling: 4 x PowerCon link 0.5 m 4 x Signal link 0.
LINK LINK OUT 2 LINK LINK LINK 6 x Convert12A 3 x LX-218CA 1 x DSP-2060/2040 LINK LINK LINK CONFIGURATIONS (cont´d) OUT 5 POWER SUPPLY POWER SUPPLY Convert 12 Accessories Rigging frames AX-Convert12 x 2 DSP-2060/2040 OUT 1 Speaker cabling: 4 x PowerCon link 0.5 m LINK POWER SUPPLY 4 x Signal link 0.
CONFIGURATIONS (cont´d) 2 x Convert12A 2 x SX-218A 1 Unit preset 1 Unit preset LINK Satellite X-Over HPF LINK POWER SUPPLY Satellite X-Over HPF POWER SUPPLY Convert 12 Accessories Rigging frames TRD-6 x 2 Speaker cabling: 2 x Signal link 2 m 1 x DSP-2060A / DSP-2040A 12 Manual del Usuario / convert series / User’s Manual
AMPLIFIER Description 1) INPUT : 1/4” Jack+XLR combined socket-type input signal connector. This is a balanced connector just like the LOOP THRU connector with the following pin assignments: 1 or S =GND (ground). 2 or T =(+) Non inverted input. 3 or R =(-) Inverted input. 2) LOOP THRU (except SUBs): XLR-type output signal connector for connecting several units together and sending them all the same signal.
120.0 dBSPL ARRAY EQ 1 UNIT 110.0 100.0 90.0 80.0 70.0 20 50 100 200 500 1k 2k Hz 5k 10k 20k convert 12A frequency response curves 120.0 dBSPL 110.0 100.0 90.0 80.0 70.0 10 100 1k 10k Hz 20k 100 1k 10k Hz 20k 120.0 dBSPL 110.0 100.0 90.0 80.0 70.
Preliminary Note Use this product only in environments E1, E2, E3 o E4(*) following EN55103-2 (Electromagnetic Compatibility. Norms. Products for professional sound, video and audiovisual systems and light control for shows use. Part 2: Immunity). Do not cover the amplifier´s radiator and don´t obstruct the ventilation. Do not plug the system in the same line that light systems, avoiding intermittency or light intensity cuts. ON / OFF A sound system should be switched on sequentially.
TroubleShooting PROBLEM CAUSE SOLUTION No sound from the unit. The SIGNAL LED does not light up. 1 – The signal source is sending no signal. 2 – Defective cable. 1 – Check that the mixer or sound source is sending signal to the UNIT. 2 – Check that the cable from the sound source to the UNIT is connected correctly. Replace the cable if defective. Full power cannot be obtained. The LIMIT LED never lights up. The signal source does not have a hot enough output.
RIGGING Warnings This manual contains needed information for flying D.A.S. Audio line array systems, description of the elements and safety precautions. To perform any operations related to flying the system, read the present document first, and act on the warnings and advice given. The goal is to allow the user to become familiar with the mechanical elements required to fly the acoustic system, as well as the safety measures to be taken during set-up and teardown.
2 1 6 5 4 3 This figures illustrate the best way to rig one enclosure to another. Firstable, push the iron piece to free the front rod (1). Turn the front rod until fix it (2). Remove the rear safety pin to free the rear rod (3). Turn the rear rod (4). 18 Hook the rear rod in the lower screw indicated on the upper enclosure (5). Up the rear until mach with the anchor slots from the rear part of the upper enclosure and insert again the safety pin (6). As you can see, the enclosures form a 15º angle.
AX-convert12 AX-convert12 structure allows to rig maximum 6 convert 12A. It has three points where you can hook the rigging slings. To control the vertical inclination use the slots from the side pieces, like other accessories and with help of the software Easy Focus. Join the first enclosure of the column to this structure with the rod described before and the safety pins. 2 1 3 AX-convert12 5 WLL: 190 kgf (418 lbf) Weight: 6 Kg (13.2 lbs) Dimmensions: 15 x 57.4 x 44.6 cm (Al x An x P) 5.9 x 22.6 x 17.
AXS-convert12 The structure AXS-convert12 is adecuated for stack, maximum, 3 convert 12A enclosures. To control the vertical inclination of the column use the slots from the side pieces, like other accessories, and with help of the software Ease Focus. To this structure will join the first enclosure of the column with the rods described before and the safety pins. convert 12A AXS-convert12 (No incluido Not included) WLL: 84 kgf (184.8 lbf) Weight: 4.1 Kg (9 lb) Dimmensions: 10.9 x 56.
TRD-2 y TRD-6 Convert 12A unit has a pole mount socket incorporated on the lower side which allows angle the enclosure between +25º to -10º when TRD-2 or TRD-6 are mounted. This mounting allows just one unit. 25º 7.
APPENDIX: Line connections: unbalanced and balanced There are two basic ways to transport an audio signal with microphone or line level: Unbalanced line: Utilising a two conductor cable, it transports the signal as the voltage between them. Electromagnetic interference can get added to the signal as undesired noise. Connectors that carry unbalanced signals have two pins, such as RCA (Phono) and ¼” (6.35mm, often referred to as jack) mono.
D.A.S. AUDIO, S.A. C/. Islas Baleares, 24 46988 Fuente del Jarro Valencia, SPAIN Tel. 96 134 0525 Tel. Intl. +34 96 134 0860 Fax 96 134 0607 Fax Intl. +34 96 134 0607 D.A.S. AUDIO OF AMERICA, INC. Sunset Palmetto Park 6816 NW 77th Court. Miami, FL. 33166 - U.S.A. TOLL FREE: 1-888DAS4USA Tel. +1 305 436 0521 Fax +1 305 436 0528 UM_CONV12A_02_EN www.dasaudio.com D.A.S. AUDIO ASIA PTE. LTD. 25 Kaki Bukit Crescent #01-00/02-00 Kaki Bukit Techpark 1 Singapore 416256 Tel.