Systems Guide variant series
variant
SYSTEM INSTALLATION The variant 25A/112A units can be installed in a number of ways. Typically several variant 25A/112A units would be assembled to form a line array cluster, but it can also be used alone, as a frontfill or as an under- balcony unit. A wide range of accessories and uses are available, and have been described in the paragraphs below.
The procedure to mechanically connect the second unit is similar. First rotate the connecting links (5) in order to select the correct angle by means of the safety pins (6). In this example the selected angle is 2º. Once this has been done then the enclosure must be hung from the first box (7) and assured by means of one more safety pin (8). 3 4 1 2 7 variant 25A - max 20 units 4 3 8 2 1 The above described procedure applies to the rest of the units.
Assembling a system with flown subwoofers The variant 18A units feature integral rigging hardware allowing them to be flown independently or above variant 25A enclosures. -5º 0º 5º 0º VARIANT 18 AX-V25 1 VARIANT 25 The first step will be to mechanically connect the first variant 18A to the AX-V25 grid. 6 safety pins are included in the rear side of the box in order to do so.
0º 5º VARIANT 25 -5º 0º VARIANT 18 AX-V25 The procedure in case of installing variant 112A systems is equivalent to the previous mentioned before. 1 2 9 8 7 Before attaching the first variant 25A to the subwoofer unit, the connecting links must be rotated (3) until the desired splay angle with the next unit on top is reached. Once the desired angle has been reached the safety pins will be introduced (4) into the corresponding hole.
In the picture above the safety pin has been introduced into the 0º labeled hole, while in the picture below the safety pin has been introduced into the +5º labeled hole. Before attaching the first variant 112A to the subwoofer unit, the connecting links must be rotated (3) until the desired splay angle with the next unit on top is reached. Once the desired angle has been reached the safety pins will be introduced (4) into the corresponding hole.
System installation using the ceiling support AXC-V25 The variant 25A units can be set up as a long array of more than four enclosures (as explained above) or as a small array of 2, 3 or 4 units. In the latter case the highly resistant AX-V25 grid accessory is not necessary. Instead the AXC-V25 ceiling mount accessory can be used to hang a cluster of up to four units. Grower (lock) washer Metal washer First attach the ceiling mount accessory to the ceiling or a beam.
20º When a pair of hook clamps are attached to the ceiling mount accessory, it can be fixed to a truss structure such as the one shown in the picture below: The AXC-V25 accessory can also be used as a support for up to two variant 25A units on a pole mount accessory, on top of one variant 18A unit. To do so the AXC-V25 accessory is to be used upside-down and a special pole mount adaptor must be fixed to it by means of two M8x35 DIN912 screws, nuts and washers.
The variant 112A units can be set up as a cluster of more than three enclosures (as explained above) or as a small array of 2 units. In the latter case the highly resistant AX-V25 grid accessory is not necessary. Instead the AXC-V112 ceiling mount accessory can be used to hang a cluster of up to four units. Grower (lock) washer Metal washer First attach the ceiling mount accessory to the ceiling or a beam. Before doing so be sure that the load bearing capability of these elements is enough.
When a pair of hook clamps (AXC-AT) are attached to the ceiling mount accessory, it can be fixed to a truss structure such as the one shown in the picture below: The AXC-V112 accessory can also be used as a support for up two variant 112A unit on a pole mount accessory, on top of one variant 18A unit. To do so the AXC-V112 accessory is to be used upside-down and a special pole mount adaptor must be fixed to it by means of two M8x35 DIN912 screws, nuts and washers.
System installation using the wall support AXW-V25 Up to three variant 25A units can be wall mounted by means of the AXW-V25 accessory. Grower washer First the accessory must be fixed to the wall, making sure in advance that the work load of the wall allows for it. The wall mount accessory will be attached to the wall using six nº 10 rawlplugs and six 7 x 40 mm screws. Metal washer M8x35 DIN 912 Rubber washer Then hang the first variant 25A unit from the wall mount accessory.
SI_VA_01_EN www.dasaudio.com D.A.S. AUDIO, S.A. C/. Islas Baleares, 24 46988 Fuente del Jarro Valencia, SPAIN Tel. 96 134 0525 Tel. Intl. +34 96 134 0860 Fax 96 134 0607 Fax Intl. +34 96 134 0607 D.A.S. AUDIO OF AMERICA, INC. Sunset Palmetto Park 6816 NW 77th Court. Miami, FL. 33166 - U.S.A. TOLL FREE: 1-888DAS4USA Tel. +1 305 436 0521 Fax +1 305 436 0528 D.A.S. AUDIO ASIA PTE. LTD. 25 Kaki Bukit Crescent #01-00/02-00 Kaki Bukit Techpark 1 Singapore 416256 Tel.
