D.B. Smith Professional Series Sprayers Use and Care Manual (“O” Style) (“R” Style) CAUTION: Read and follow all instructions Do Not Return This Sprayer To The Store For Help, Information or Parts, Call : 1-800-311-9903 The Fountainhead Group, Inc. 23 Garden St., New York Mills, NY 13417 1-800-311-9903 www.TheFountainheadGroup.com Manual No.
SAFETY PRECAUTIONS • Read owner’s manual completely before operating this sprayer. • Always use goggles, gloves, and protective clothing when using sprayer. • Read and follow all instructions and cautions on label of products used in this sprayer. • Never use flammable liquids, caustics, acids, or hot water in this tank. • Do not leave sprayer in the sun when not in use. • Spray when air is calm to prevent drift of chemicals.
ASSEMBLY INSTRUCTIONS Assemble Hose To Tank IMPORTANT: Do not attempt to heat or alter hose, hose nut, or barb prior to assembly. 1. Align hose barb tabs, push hose barb into tank until it stops (See Figure A). 2. Slide hose nut into place and turn clockwise to tighten. (See Figure B). NOTE: Do not use tools to tighten hose nut. Figure A Figure B Assemble Extension, Shut-Off & Nozzle 1. Install the extension onto the shut-off assembly and tighten the nut securely. (See Figure C) 2.
OPERATING INSTRUCTIONS Filling IMPORTANT: Always make sure the pressure is released from the tank before filling or servicing. If equipped, pull up on the knob of the pressure release valve until all the pressure is released from the tank. Otherwise, squeeze and hold shut-off lever until the unit stops spraying. Then, and only then, it is safe to remove pump. 1. Turn the pump handle counterclockwise to remove the pump (See Figure E). 2. Fill the tank to the desired level. See fill markings on side of tank.
OPERATING INSTRUCTIONS CONTINUED Finish 1. Depressurize the tank as described in Release Tank Pressure section. 2. Turn the pump handle counterclockwise to remove the pump. 3. Empty any remaining liquid according to the product disposal directions. 4. Follow the Cleaning instructions. Cleaning 1. Remove the pump as described in the Finish section. 2. Fill the tank with cool, clean tap water. Replace the pump and tighten securely. 3. Agitate the tank to rinse the chemical from the tank wall and pump. 4.
MAINTENANCE CONTINUED 3. Inspect o-ring. If worn or damaged, remove and replace. Lubricate o-ring with petroleum jelly. (See Figure 4) 4. Inspect check valve in bottom of barrel. If worn or damaged, remove and replace by pressing into hole in bottom of barrel. (See Figure 5) 5. Re-install the barrel into the cap. While holding the cap securely, turn the barrel clockwise to lock the tabs in place. Figure 4 Figure 5 “R” Style 1. Inspect gasket. If worn or damaged, remove and replace. (See Figure 6) 2.
Shut-off Maintenance (Smith Pro II) Always depressurize sprayer before maintenance by activating shut-off and spraying contents out. 1. Unscrew the handle from the shut-off assembly. 2. Remove the filter from the shut-off assembly. 3. Clean any debris from inside the handle, shut-off assembly, or the filter by rinsing with cool, clean water. 4. Reassemble the components as shown and tighten all connections securely. C A B A. Handle B. Filter C.
KITS, PARTS & ACCESSORIES 8-1 8-2 9B 9A 8-3 11B 11A 11D 9E 9D KIT #9 10B 10C 10E 10A 10F 9F 10D KIT #11 11C 11E 7-18 7-14 KIT #10 9C 11A 11B 11C 7-SS 7-21 11E 11F 11G 11F 11D KIT #5 5A KIT #2 2A 5B 2B 5C 2C 5D 2D 5E 2E 5F 2F 5G 2G 4 1-1 1-2 1-2 “O” 3-2 “R” 3-3 Page 8
“O” SPRAYER PARTS KEY# 1 -1 -2 -3 PART# DESCRIPTION KEY# PART# DESCRIPTION 181052 181036 181120 -2 3 -3 4 182264 182265 180836 1 GALLON “O” TANK 2 GALLON “O” TANK 3 GALLON “O” TANK 180279 178040 180278 180388 178041 178039V 171015V 2 GALLON “R” TANK (INCLUDES KEY #4) 3 GALLON “R” TANK (INCLUDES KEY #4) PRV ASSEMBLY KIT #5 182259 “R” PUMP KIT #2 180398 “O” PUMP 2A 2B 2C 2D 2E 2F 2G “R” SPRAYER PARTS “O” PUMP HANDLE “O” PUMP CAP “O” PUMP ROD “O” PUMP PISTON ASSEMBLY “O” PUMP BARREL “O” PUMP GASK
SERVICE KITS, PARTS & ACCESSORIES ARE AVAILABLE BY CONTACTING The Fountainhead Group, Inc. - Customer Service Center Monday - Friday 8 A.M. - 5 P.M., EST Toll Free: 1-800-311-9903 or e-mail: Info@TheFGI.com or Access online at: www.TheFountainheadGroup.
D.B. Atomizadores de la Serie Profesional Smith Manual de uso y cuidado (Estilo “O”) (Estilo “R” ) PRECAUCIÓN: Lea y siga todos las instrucciones No devuelva este atomizador a la tienda Para obtener ayuda, información o piezas, llame al: 1-800-311-9903 The Fountainhead Group, Inc. 23 Garden St., New York Mills, NY 13417 1-800-311-9903 www.TheFountainheadGroup.com Manual No.
PRECAUCIONES DE SEGURIDAD • Lea todo el manual del usuario antes de operar este atomizador. • Siempre utilice gafas de seguridad, guantes y ropa protectora cuando use el atomizador. • Lea y siga todas las instrucciones y precauciones que se muestran en la etiqueta de los productos que se usan en este atomizador. • Nunca utilice líquidos inflamables, agentes cáusticos, ácidos o agua caliente en este tanque. • No deje el atomizador expuesto al sol cuando no esté en uso.
INSTRUCCIONES DEL ENSAMBLAJE Ensamble la manguera en el tanque IMPORTANTE: No intente calentar ni alterar la manguera, tuerca de manguera o conector dentado antes del ensamblado. 1. Alinee las lengüetas de la espiga de la manguera, presione la espiga de la manguera en el tanque hasta que se detenga. (Vea la Figura A). 2. Deslice la tuerca de la manguera hasta su lugar y gire en sentido horario para ajustar. (Vea la Figura B).
INSTRUCCIONES DE OPERACIÓN Llenado IMPORTANTE: Siempre asegúrese de que se ha liberado la presión del tanque antes de llenar o utilizar. Si provista, jale hacia arriba la perilla de la válvula de liberación de presión hasta que se libere toda la presión del tanque. De lo contrario, apriete y sostenga la palanca de la válvula de cierre hasta que la unidad deje de rociar. Después, y solamente después, es seguro quitar la bomba. 1.
INSTRUCCIONES DE OPERACIÓN (continuación) Finalización 1. Despresurice el tanque según se describe en la sección Libere la presión del tanque. 2. Gire el mango de la bomba en sentido antihorario para quitar la bomba. 3. Vacíe todo el líquido restante de acuerdo con las intrucciones de desecho del producto. 4. Siga las instrucciones de Limpieza. Limpieza 1. Quite la bomba según se describe en la sección Finalización. 2. Llene el tanque con agua de grifo fresca y limpia.
MANTENIMIENTO (continuación) 3. Inspeccione la junta tórica. Si está gastada o dañada, sáquela y reemplácela. Lubrique la junta tórica con gel de petróleo. (Vea la Figura 4) 4. Inspeccione la válvula de retención en el fondo del cilindro. Si está gastada o dañada, sáquela y reemplácela presionando en el orificio en el fondo del cilindro. (Vea la Figura 5) 5. Reinstale el cilindro en la tapa. Mientras sujeta la tapa firmemente, gire el cilindro en sentido horario para fijar las trabillas en su lugar.
Mantenimiento del dispositivo de cierre (Smith Pro) Siempre despresurice el atomizador antes de darle mantenimiento al activar el cierre y atomizador los contenidos hacia afuera. A B 1. Destornille el mango del dispositvo de cierre. 2. Retire el filtro del dispositivo de cierre. 3. Limpie todo residuo presente en el interior del mango A. Mango y del despositivo de cierre o en el asiento de válvula filtro. B. Filtro C. Dispositivo de cierre 4.
JUEGOS, PIEZAS Y ACCESORIOS 8-1 8-2 9B 9A 8-3 11B 11A 11D 9E 9D KIT #9 10B 10C 10E 10A 10F 9F 10D KIT #11 11C 11E 7-18 7-14 KIT #10 9C 11A 11B 11C 7-SS 7-21 11E 11G 11F 11F 11D KIT #5 5A KIT #2 2A 5B 2B 5C 2C 5D 6C 2D 5E 2E 5F 2F 5G 2G 4 1-1 1-2 1-2 “O” 3-2 “R” 3-3 página 18
PARTES DEL ATOMIZADOR “O” No. DE No. DE DESCRIPCIÓN CLAVE PIEZA 1 -1 -2 -3 181052 181036 181120 TANQUE “O” DE 1 GALÓN TANQUE “O” DE 2 GALONES TANQUE “O” DE 3 GALONES KIT No.2 180398 LA BOMBA “O” 2A 2B 2C 180270 178040 180278 MANGO “O” DE LA BOMBA TAPA “O” DE LA BOMBA VARILLA “O” DE LA BOMBA ENSAMBLADO DEL PISTÓN “O” DE LA 180388 BOMBA 178041 CILINDRO “O” DE LA BOMBA EMPAQUETADURA “O” DE LA BOMBA, 178039V VITON 171015V VÁLVULA DE RETENCIÓN, VITON 2D 2E 2F 2G PARTES DEL ATOMIZADOR “R” No. DE No.
LOS JUEGOS DE REPARACIÓN, PIEZAS Y ACCESORIOS SE ENCUENTRAN DISPONIBLES COMUNICÁNDOSE A The Fountainhead Group, Inc. - Centro deservicio al cliente De lunes a viernes de 8 A.M. a 5 P.M., EST Llame sin costo al: 1-800-311-9903 o Correo electrónico: Info@TheFGI.com o Ingrese en línea a: www.TheFountainheadGroup.