Quick Installation Guide Nuclias Cloud-Managed AC1300 Wave 2 Outdoor Access Point DBA-3621P Additional documentation is also available on the D-Link website
Contents English 1
Hardware Overview This installation guide provides instructions for installing the DBA-3621P on your network. Additional documentation is also available on the D-Link support website. LED Indicators • ENGLISH Before You Begin Nuclias Cloud Manual: For additional information and instructions on how to configure the device using Nuclias Cloud.
Interface Connectors # Connector Description Wall/Pole Mount to connect to the mounting Mount plate on a wall or a pole. Grounding Connector for the grounding wire. 2 Wire ENGLISH 1 Table 3: Interface Description 1 2 Installation 3 Figure 2: Bottom Connectors Using Power over Ethernet (PoE) # Connector Description LAN(PoE) Gigabit RJ-45 port for data and 1 Port Power over Ethernet (PoE). Press and hold for 10 seconds to 2 Reset factory reset the device.
Connecting Wirelessly 1. 2. 1. 2. Manual Configuration Note: The management computer, DHCP server and DBA-3621P must be in the same subnet. If you are unable to connect to Nuclias Cloud, you may need to manually configure the DBA-3621P using its web user interface. Use one of the following methods to access the web user interface: 3. Connect the management computer to the default SSID of the DBA-3621P.
Wall Mounting ENGLISH Pole Mounting Figure 5: Attaching the Mounting Base 1. Secure the mount base to the pole using the U-bolt and the four included nut fasteners. Figure 7: Attaching the Mounting Plate 1. Figure 6: Mounting the Device 2. Align and attach the DBA-3621P to the mounting base using the four included screws and washers. Figure 8: Mounting the Device 2. 3. 4. 4 Align and attach the DBA-3621P to the mounting plate using the four included screws and washers.
Connecting the Grounding Wire ENGLISH Figure 11: Attaching the Grounding Wire Figure 9: Attaching the Grounding Wire 3. 1. A grounding wire is recommended to protect your device from lightning strikes and the buildup of static electricity. Attach the grounding wire to the DBA-3621P using the included screw. Attach the other end of the grounding wire to either the wall or the pole mount. Ensure that the wall or the pole mount is connected to an electrical ground.
Appendix - Statements Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Professional installation instruction Please be advised that due to the unique function supplied by this product, the device is intended for use with our interactive entertainment software and licensed third-party only. The product will be distributed through controlled distribution channel and installed by trained professional and will not be sold directly to the general public through retail store. 1. 2. 3. 4. 5.
(ii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. (iii) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
requirement. External antenna U se only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of ISED limit and is prohibited. 4. Installation procedure Please refer to user’s manual for the detail. Warning Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules.
for that type, are strictly prohibited for use with this device. Le présent émetteur radio (IC: 4216A-BA3621PA1 / Model: DBA-3621PA1) a été approuvé par ISED pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur. Approved antenna(s) list Type Dipole Gain Brand Manufacturer 2.4~2.45GHz-----3.
Notes
Notes
Notes
Notes
Ver. 1.
