Version 1.
Preface D‐Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date 1.00 July 2, 2016 Description • Initial Release Trademarks D‐Link and the D‐Link logo are trademarks or registered trademarks of D‐Link Corporation or its subsidiaries in the United States or other countries.
Table of Contents Table of Contents Preface ...................................................................... i Manual Revisions .............................................................. i Trademarks ....................................................................... i Power Usage .................................................................. i Product Overview ..................................................... 1 Package Contents ........................................................
Section 1 ‐ Product Overview Product Overview Package Contents DCH‐G022 mydlink™ Connected Home Hub Quick Install Card Quick Install Card Power Adapter Ethernet Cable Warranty Document If any of the above items are missing from your package, please contact your reseller.
Section 1 ‐ Product Overview System Requirements General Requirements • Wireless router with Internet Service • An available power outlet Mobile Requirements • iPhone, iPad, or Android smartphone or tablet1 1 Please refer to the mobile app’s store page to check whether your device is compatible.
Section 1 ‐ Product Overview Introduction Features Use Motion Detection to Automatically Turn on Your Appliances The DCH‐G022 mydlink™ Connected Home Hub is a Z‐Wave gateway used to control a variety of Z‐Wave sensors for home automation. The DCH‐G022 communicates with other Z‐Wave and D‐Link Connected Home devices, letting you manage your home automation system on a single platform either at home or on‐the‐go. Simply put, the DCH‐G022 is the control center to your home automation system.
Section 1 ‐ Product Overview Hardware Overview Front/Top 1 2 1 2 LED Reset Button D‐Link DCH‐G022 User Manual Solid Green The device is connected to the network. Solid Orange The device is not connected to the network. Flashing Orange WPS or Z‐Wave pairing/unpairing is underway. Solid Red The device is defective. Light Off The device is powered off. Pressing the reset button for 10 seconds will reset the DCH‐G022 to the factory default settings.
Section 1 ‐ Product Overview Hardware Overview Side and Bottom 1 2 3 4 1 USB Port Features using this port may be provided in the future. 2 LAN Ports Connect to your router using an Ethernet cable. 3 4 WPS/Pair Button Pressing the WPS button for 1 second allows you to connect with Wi‐Fi clients using Wi‐Fi Protected Setup Power Input D‐Link DCH‐G022 User Manual Connect the included 5 V/2 A power adapter to power the device.
Section 2 ‐ Installation Wireless Installation Factors The mydlink™ Connected Home Hub lets you automate appliances using your existing wireless network. Keep in mind, however, that the number, thickness, and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business.
Section 2 ‐ Installation Hardware Installation Mounting Your Device (Optional) Step 1: Place the mounting bracket where you want to position the hub and use a pencil to mark the holes. Step 2: Depending on the material of the wall or ceiling, use proper tools to drill two holes 25 mm deep with a 6 mm drill bit where you marked. After drilling the holes, insert plastic anchors to support the screws. Step 3: If desired, cables can be concealed behind the mounting bracket.
Section 2 ‐ Installation Step 4: Fasten the mounting bracket to the wall using the screws provided. Step 5: Line up the holes on the device with the tabs on the mount and slide the device towards the wall to fasten the hub to the mounting bracket. Connect the power cable to the hub.
Section 2 ‐ Installation Setting Up Your Device To install your DCH‐G022, first download and install the mydlink™ Home app on your mobile device. This app will walk you through installing and configuring your DCH‐G022. Step 1: On your mobile device, download mydlink Home by going to mydlinkhomeapp.dlink.com, or by searching for mydlink Home in the App Store or Google Play. Step 2: Launch the mydlink Home app and create a new account or sign in to your existing account.
Section 2 ‐ Installation Once you have set up your DCH‐G022, you can tap on the device icon to view information such as your network details and also perform a factory reset. Please consult your devices’ instruction manual to connect it to your mydlink™ Connected Home Hub. After you have paired your Connected Home device with the DCH‐G022, you can customize your home’s automation policies. • To create new policies for devices connected to your DCH‐G022, please go to My Actions on page 15.
Section 3 ‐ Usage mydlink™ Home My Devices Tapping a connected device under the My Devices page will take you to the device’s settings. Motion Enable or disable motion detection. Detection: Last Detection: Displays the last time the sensor detected motion. Sensitivity: Adjust the sensitivity of the sensor to motion. Information: This page will show detailed information about the product and your network. You can also perform a factory reset here by tapping Reset.
Section 3 ‐ Usage Schedule You can customize schedules for when your DCH‐G022 will be active in this section. There are two types of schedules you can configure: Basic and Advanced. The Basic type lets you set a specific time and cycle for select days. The Advanced type lets you specify different timeframes for each day of the week.
Section 3 ‐ Usage Tapping + on the top right corner of the Advanced schedule page will take you to the page where you can select different days and times that the device will be active in a table. Simply tap and drag the bars in the table to adjust the times. Tap x to delete a specific time. After the schedule is set, go back to the previous page and tick the radio button next to the rule to activate it.
Section 3 ‐ Usage Information This page shows your product and related network details. Product Name: Displays the product model. mydlink Num‐ Displays the mydlink number assigned to this ber: device. MAC Address: Displays the MAC address of the device. IP Address: Displays the LAN IP Address of the device. Firmware Displays the version of the firmware. Version: Factory Reset: Tap Reset to perform a factory reset.
Section 3 ‐ Usage My Actions This page lets you add and enable/disable rules which execute actions such as notifications when your DCH‐G022 detects motion. Tap to switch between pages. 1. To add a new action for you device, tap on New action. 2. Type in a name for this action. Tap Done when you’ve finished inputting the name. 3. To select the device you want to use as the trigger for this action, tap + then choose from the list of devices.
Section 3 ‐ Usage 4. Select from the available conditions for this device and tap Next. 5. Tap + to select from the available responders for this device.
Section 3 ‐ Usage 6. Select from the available responders for this device. In this example we have chosen to send a notification. 7. Check the action settings and tap Done to finish. 8. To delete the rule, simply swipe right on the rule to show the trash icon. Tap on the icon to delete it.
Section 3 ‐ Usage My Places This page lets you add devices into a group so you can easily see which devices are in a particular location. 1. To create a group, tap New group. 2. On the New Group page, tap the icon to choose an icon or photo for the group. Tap next to it to enter a name for the group. Then tap the + icon to add devices. 3. Tick the devices to be included in this group and tap Done.
Section 3 ‐ Usage 4. Your group is created and will show up in My Places. Tapping each device in the group will take you to their settings. You can tap the icon to activate/deactivate the device.
Section 3 ‐ Usage Advanced Configuration The DCH‐G022 has a web configuration for users who wish to set advanced settings. To go to the configuration page, open your browser and enter the IP address of your Z‐Wave hub. For the User Name, enter admin. For the password, enter the 6‐digit PIN code on the device label.
Section 3 ‐ Usage Firmware Upgrade To upgrade the firmware on your DCH‐G022, visit the D‐Link support website at http://support.dlink.com/ and download the latest firmware file for your device. You can then upload the file from this page to being the upgrade process.
Section 3 ‐ Usage Factory Default To reset your DCH‐G022 to its factory default settings, click Restore Factory Defaults. You also have the option to reset the device settings without removing configurations for your Z‐Wave controller by clicking Partial Reset.
Section 3 ‐ Usage Z‐Wave Main The Z‐Wave Main page lets you manage Z‐Wave devices connected to your DCH‐G022. Include New A device must be “included” to the Z‐Wave Device: network before it can be controlled via Z‐W ave(DCH‐G022). This process (also known as “pairing” and “adding”) is achieved by pressing/(hold for 5 seconds) “Wireless button” Exclude De‐ on DCH‐G022 or pushing the [Include NEW vice: Device]([Exclude Device]) button on GUI being into the inclusion(exclusion) mode.
Section 3 ‐ Usage Z‐Wave Nodes This page lets you manage the advanced features of other Z‐Wave sensors. To remove the failed node: To replace the failed node. Send the BASIC SET ON command to switch the node ON. Send the BASIC SET OFF command to switch the node OFF. Send the BASIC GET command to the selected node.
Section 5 ‐ Troubleshooting Troubleshooting How do I reset the DCH‐G022? When you reset your DCH‐G022, it will change your settings back to the factory default settings. To reset the device, locate the Reset button on the side of the device. With the device plugged in, press and hold the Reset button for about 10 seconds until the Power LED turns red.
Appendix A ‐ Technical Specifications Technical Specifications Standards • IEEE 802.11b • IEEE 802.11n • IEEE 802.11g Network Protocols • ARP, ICMP • TCP/IP • IPv4 and IPv6 • HNAP • DHCP client • NTP client • Bonjour Wireless Frequency Range 1 • 868.40 MHz (Europe / China / Singapore / South Africa / UAE) • 908.40 MHz (United States / Canada / Mexico / Chile) • 916.00 MHz (Israel) • 919.80 MHz (Hong Kong) • 921.40 MHz (Australia / New Zealand / Brazil) • 922.50/923.90/926.
Appendix B ‐ Regulatory Statements Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix B ‐ Regulatory Statements IMPORTANT NOTICE: FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. Industry Canada Statement: This device complies with Industry Canada licence‐exempt RSS standard(s).
Appendix B ‐ Regulatory Statements NCC 警語： 以下警語適用台灣地區 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率 射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通 信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 D‐Link DCH‐G022 User Manual 29
Appendix B ‐ Regulatory Statements European Union: This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. For more information, please refer to the Declaration of Conformity. Notice of Wireless Radio LAN Usage in The European Community: • This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France where restrictive use applies.
Appendix B ‐ Regulatory Statements 2.4 GHz Wireless Frequency and Channel Operation in EEC Countries: Region Frequency Band Max output power (EIRP) Metropolitan 2400 ‐ 2454 MHz 100 mW Guadeloupe, Martinique, St Pierre et Miquelon, Mayotte 2454 ‐ 2483.5 MHz 100 mW indoor, 10 mW outdoor Reunion et Guyane 2400 ‐ 2483.5 MHz 100 mW Rest of EU community 2420 ‐ 2483.5 MHz 100 mW R&TTE 1999/5/EC WLAN 2.4 ‐ 2.4835 GHz IEEE 802.11b/g/n Spectrum Regulation MHz, Europa (ETSI) max.
Appendix B ‐ Regulatory Statements European Community Declaration of Conformity: Česky [Czech] D‐Link tímto prohlašuje, že tento <###> je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede D‐Link erklærer herved, at følgende udstyr <###> overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Appendix B ‐ Regulatory Statements Polski [Polish] Niniejszym D‐Link oświadcza, że <###> jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Portuguese] D‐Link declara que este <###> está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] D‐Link izjavlja, da je ta <###> v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
Appendix B ‐ Regulatory Statements Disposing of and Recycling Your Product ENGLISH EN This symbol on the product or packaging means that according to local laws and regulations this product should be not be disposed of in household waste but sent for recycling. Please take it to a collection point designated by your local authorities once it has reached the end of its life, some will accept products for free.
Appendix B ‐ Regulatory Statements FRANÇAIS FR Ce symbole apposé sur le produit ou son emballage signifie que, conformément aux lois et règlementations locales, ce produit ne doit pas être éliminé avec les déchets domestiques mais recyclé. Veuillez le rapporter à un point de collecte prévu à cet effet par les autorités locales; certains accepteront vos produits gratuitement. En recyclant le produit et son emballage de cette manière, vous aidez à préserver l’environnement et à protéger la santé de l’homme.
Appendix B ‐ Regulatory Statements ITALIANO IT La presenza di questo simbolo sul prodotto o sulla confezione del prodotto indica che, in conformità alle leggi e alle normative locali, questo prodotto non deve essere smaltito nei rifiuti domestici, ma avviato al riciclo. Una volta terminato il ciclo di vita utile, portare il prodotto presso un punto di raccolta indicato dalle autorità locali. Alcuni questi punti di raccolta accettano gratuitamente i prodotti da riciclare.
Appendix B ‐ Regulatory Statements POLSKI PL Ten symbol umieszczony na produkcie lub opakowaniu oznacza, że zgodnie z miejscowym prawem i lokalnymi przepisami niniejszego produktu nie wolno wyrzucać jak odpady czy śmieci z gospodarstwa domowego, lecz należy go poddać procesowi recyklingu. Po zakończeniu użytkowania produktu, niektóre odpowiednie do tego celu podmioty przyjmą takie produkty nieodpłatnie, dlatego prosimy dostarczyć go do punktu zbiórki wskazanego przez lokalne władze.
Appendix B ‐ Regulatory Statements MAGYAR HU Ez a szimbólum a terméken vagy a csomagoláson azt jelenti, hogy a helyi törvényeknek és szabályoknak megfelelően ez a termék nem semmisíthető meg a háztartási hulladékkal együtt, hanem újrahasznosításra kell küldeni. Kérjük, hogy a termék élettartamának elteltét követően vigye azt a helyi hatóság által kijelölt gyűjtőhelyre. A termékek egyes helyeken ingyen elhelyezhetők.
Appendix B ‐ Regulatory Statements DANSK DK Dette symbol på produktet eller emballagen betyder, at dette produkt i henhold til lokale love og regler ikke må bortskaffes som husholdningsaffald, mens skal sendes til genbrug. Indlever produktet til et indsamlingssted som angivet af de lokale myndigheder, når det er nået til slutningen af dets levetid. I nogle tilfælde vil produktet blive modtaget gratis.
Appendix B ‐ Regulatory Statements SVENSKA SE Den här symbolen på produkten eller förpackningen betyder att produkten enligt lokala lagar och föreskrifter inte skall kastas i hushållssoporna utan i stället återvinnas. Ta den vid slutet av dess livslängd till en av din lokala myndighet utsedd uppsamlingsplats, vissa accepterar produkter utan kostnad. Genom att på detta sätt återvinna produkten och förpackningen hjälper du till att bevara miljön och skydda människors hälsa.
Caution There is an explosion risk if an incorrect battery type is installed in the device. Dispose of used batteries by following your local regulations.
