DCM-604 Cable Modem EMTA Gateway PacketCable 1.5 and DOCSIS 2.0 Certified 4 Ports Ethernet Cable Router with 2 Ports Voice User’s Manual Version 0.
FCC Statement This device complies with Class B Part 15 of the FCC Rules. The device generates, uses and can radiate radio frequency energy and, if not installed and used as instructed, may cause harmful interference to radio communication. Only Coaxial cables are to be used with this device in order to ensure compliance with FCC emissions limits. Accessories connected to this device by the user must comply with FCC Class B limits.
Table of Contents 1. INTRODUCTION................................................................................................1 1.1 1.2 1.3 2. SYSTEM REQUIREMENTS .................................................................................1 UNPACKING AND INSPECTION .........................................................................1 SAFETY PRECAUTIONS ....................................................................................1 HARDWARE OVERVIEW.....................................
DCM-604 Cable Modem EMTA Gateway 1. User’s Manual Introduction The DCM-604 is a Voice over IP Wireless Residential Gateway integrated with Cable Modem which allows you implement your VoIP phone call directly through Cable Modem Broadband Network service with its built-in PacketCable 1.5 and DOCSIS/EURODOCSIS 2.0 compliant specification. And with the integration of 4 ports switch and IEEE 802.
DCM-604 Cable Modem EMTA Gateway 2. Hardware Overview 2.1 Front Panel and LEDs User’s Manual There are fourteen Light-Emitting-Diodes (LEDs) located on the front panel top provide status information to the user.
DCM-604 Cable Modem EMTA Gateway WPS Blue User’s Manual Blinking WPS Activating On WPS Connected Off No WPS Connection 2.2 Rear Panel and Hardware Connection This chapter describes the proper steps for connecting your cable modem. Please be sure to follow the steps in the sequence outlined below. Failure to do so could result in improper operation or failure of your cable modem.
DCM-604 Cable Modem EMTA Gateway 3. User’s Manual Ethernet Installation The LAN port you are using is auto-negotiating 10/100Mbps (Switch) Ethernet Interface. You can use the Ethernet port to connect to the Internet with an Ethernet network device such as NIC/Hub/Switch through RJ45.
DCM-604 Cable Modem EMTA Gateway 4. User’s Manual USB Driver Installation Using the USB port to connect to the Internet allows you to install the cable modem more quickly and easily than connecting to the Internet using the Ethernet port, since you do not need to install a network interface card (NIC). 4.1 Windows XP 1. Connect USB cable from PC to cable modem. 2. Connect RF cable and power on Cable Modem. Wait until it register, it will take about 40 seconds to 4 minutes depends on network traffic.
DCM-604 Cable Modem EMTA Gateway User’s Manual 6. Windows will locate the driver automatically. Please click Continue Anyway to continue the installation process. 7. Windows shall find the location of USB driver and complete the installation. Click Finish.
DCM-604 Cable Modem EMTA Gateway 4.2 User’s Manual Windows 2003 1. Connect USB cable from PC to cable modem. 2. Connect RF cable and power on Cable Modem. Wait until it register, it will take about 40 seconds to 4 minutes depends on network traffic. Cable Modem may reboot if you previously connect it through Ethernet port. 3. Windows will prompt new hardware found, insert the Driver CD into your CD-ROM drive. 4. Select “Yes, this time only” and then click Next. 5.
DCM-604 Cable Modem EMTA Gateway User’s Manual 6. Windows will locate the driver automatically. Please click Continue Anyway to continue the installation process. 7. Windows shall find the location of USB driver and complete the installation. Click Finish.
DCM-604 Cable Modem EMTA Gateway User’s Manual 4.3 Windows Vista 1. Connect USB cable from PC to cable modem. 2. Connect RF cable and power on Cable Modem. Wait until it register, it will take about 40 seconds to 4 minutes depends on network traffic. Cable Modem may reboot if you previously connect it through Ethernet port. 3. Windows will prompt new hardware found, insert the Driver CD into your CD-ROM drive. 4. Click “Locate and install driver software (recommended)” item 5.
DCM-604 Cable Modem EMTA Gateway User’s Manual 6. During the driver installation, your system may pop-up a dialogue as below window, just click “Install this driver software anyway”. 7. During the driver installation, your system may pop-up a dialogue as below window, just click “Install this driver software anyway”. 8. Click “Close” button to finish the driver installation.
DCM-604 Cable Modem EMTA Gateway 5. User’s Manual Web Management For easy-changing the default setting or quick-checking diagnostics for troubleshooting, a Web-based GUI is built-in for your access. 5.1 Enter Modem's IP address Use the following procedures to login to your DCM-604. 1. Open your web browser. You may get an error message. This is normal. Continue on to the next step. 2. Type the default IP address of the DCM-604 (e.g. 192.168.0.1) and press Enter. 3. The Log In page appears.
DCM-604 Cable Modem EMTA Gateway User’s Manual There are seven categories in this web management including Status, Basic, Advanced and Firewall. The following sections describe their details. 5.2 Status The Status page shows hardware and software information about the DCM604 that may be useful to your cable service provider. 5.2.
DCM-604 Cable Modem EMTA Gateway 5.3 User’s Manual Basic The Basic page contains the basic features of DCM-604 including Setup, DHCP and Backup 5.3.1 Setup This setup page allows configuring the basic features of the broadband gateway related to your ISP's connection. 5.3.2 DHCP The DHCP page allows you to activate/deactivate the DHCP server function of the DCM-604, and, if the DHCP server is activated, to see DHCP leases it has provided.
DCM-604 Cable Modem EMTA Gateway User’s Manual With this function activated, your cable service provider’s DHCP server provides one IP address for the DCM-604, and the DCM-604’s DHCP server provides IP addresses, starting at the address you set in Starting Local Address field, to your PCs. A DHCP server leases an IP address with an expiration time. To set the maximum number of PCs to which the DCM-604 will issue IP addresses, enter it in the Number of CPEs box and then click Apply.
DCM-604 Cable Modem EMTA Gateway User’s Manual 5.4.1 Options The Options page allows you to enable/disable some advanced features supported by DCM-604. Check the option you want to use and click Apply button to enable the function(s). WAN Blocking: To prevent others on the WAN side from being able to ping your DCM-604. With WAN Blocking on, your DCM-604 will not respond to pings it receives, effectively “hiding” your gateway.
DCM-604 Cable Modem EMTA Gateway User’s Manual 5.4.2 IP Filtering The IP Filtering page enables you to enter the IP address ranges of PCs on your LAN that you don’t permit to have outbound access ability to the WAN. These PCs can still communicate with each other on your LAN, but packets they originate to WAN addresses are blocked by the DCM-604. To enable IP Filtering feature of DCM-604, check the Enable box and click Apply button. 5.4.
DCM-604 Cable Modem EMTA Gateway User’s Manual 5.4.4 Forwarding For communications between LAN and WAN, the DCM-604 normally only allows you to originate an IP connection with a PC on the WAN; it will ignore attempts of the WAN PC to originate a connection onto your PC. This protects you from malicious attacks from outsiders. However, sometimes you may wish for anyone outside to be able to originate a connection to a particular PC on your LAN if the destination port (application) matches one you specify.
DCM-604 Cable Modem EMTA Gateway User’s Manual Port Triggering is an elegant mechanism that does the forwarding for you, each time you play the game. You can specify up to 10 port ranges on which to trigger. 5.4.6 DMZ Host The DMZ page allows you to configure a specific network device to be exposed or visible directly to the WAN (public Internet).
DCM-604 Cable Modem EMTA Gateway 5.5 User’s Manual Firewall The DCM-604 provides built-in firewall functions, enabling you to protect the system against denial of service (DoS) attacks and other unwelcome or malicious accesses to your LAN. 5.5.1 Web Filter This page allows certain Web-oriented cookies, java scripts, and pop-up windows to be blocked by the firewall. A list of "trusted computers" can also be defined that are not subject to any filters configured.
DCM-604 Cable Modem EMTA Gateway User’s Manual Specify the e-mail address and its SMTP of the administrator who needs to receive the notice of any attempted firewall violations. Type the addresses in standard Internet e-mail address format, for example, yourname@onecompany.com. Then check the Enable box to enable the alert feature and click Apply button. Click E-mail Log to immediately send the email log. Click Clear Log to clear the table of entries for a fresh start. 5.5.
DCM-604 Cable Modem EMTA Gateway 5.6 User’s Manual Parental Control 5.6.1 User Setup This page allows configuration of users. “White List Only” feature limits the user to visit only those sites specified in the Allowed Domain List in Parental Control, Basic page of his/her content rule. Actually, this page helps you to identify whether or not the Websites are blocked to access. 5.6.2 Basic Setup This page allows basic selections of rules which block certain Internet content and certain Web sites.
DCM-604 Cable Modem EMTA Gateway User’s Manual 5.6.3 Time of Day Filter This page allows configuration of time access policies to block all internet traffic to and from specific network devices based on time of day setting. And it helps to ensure that the target or connected computer cannot access the internet at all. You can selecte Everyday or a day of the week by Enabling the check box and can change the Time to All Day or specific the start and end time by entering the time.
DCM-604 Cable Modem EMTA Gateway User’s Manual 5.6.4 Local Log This page displays Parental Control Local log reporting. 5.7 Wireless 5.7.
DCM-604 Cable Modem EMTA Gateway User’s Manual 5.7.2 Primary Network 5.7.3 Advanced This page allows configuration of data rates and WiFi thresholds.
DCM-604 Cable Modem EMTA Gateway User’s Manual 5.7.4 Access Control This page allows configuration of the Access Control to the AP as well as on the connected clients.
DCM-604 Cable Modem EMTA Gateway User’s Manual 5.7.5 WMM This page allows configuration of the Wi-Fi Multimedia QoS.
DCM-604 Cable Modem EMTA Gateway 5.8 User’s Manual MTA Section MTA has 5 sub-items, which indicate the status of MTA. These information can help you to understand the parameters of MTA operation. 5.8.1 Status This page displays initialization status of the MTA.
DCM-604 Cable Modem EMTA Gateway 5.