Table of Contents Table of Contents Product Overview....................................................3 Package Contents............................................................... 3 System Requirements........................................................ 3 Introduction........................................................................ 4 Features.............................................................................. 5 Hardware Overview....................................................
Section 1 - Product Overview Product Overview Package Contents • D-Link DCS-3410 PoE Day & Night Network Camera • CAT5 Ethernet Cable • Power Adapter • Manual and Software on CD • Quick Install Guide • Camera Stand Note: Using a power supply with a different voltage than the one included with the package will cause damage and void the warranty for this product. If any of the above items are missing, please contact your reseller.
Section 1 - Product Overview Introduction The D-Link DCS-3410 PoE Day & Night Network Camera is a powerful surveillance system that can connect to your network. The DCS-3410 differs from a conventional PC Camera because it is a standalone system with a built-in CPU and Web server, providing a low-cost solution capable of solving demanding security and home/office monitoring needs. It is designed with aluminum casing for maximum heat dissipation and better protection.
Section 1 - Product Overview Features • Supports a Variety of Protocols: Supporting TCP/IP networking, SMTP e-mail, HTTP and other Internet related protocols, the DCS3410 Network Camera can be integrated easily into other Internet/Intranet applications because of its standards-based features.
Section 1 - Product Overview Hardware Overview Microphone Connector The DCS-3410 PoE Day & Night Network Camera has an internal microphone built-in. However, you have the option of using an external microphone by plugging it into the microphone connector. Ethernet Cable Connector (PoE) The Network Camera’s back panel features an RJ-45 connector for connections to 10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling.
Section 1 - Product Overview Hardware Overview I/O Connector The DCS-3410 provides a terminal block with three pairs of connectors situated on the back panel. Two pairs are for input and the other is for output. The I/O connectors provide the physical interface to send and receive digital signals to and from a variety of external devices. Power LED The power LED is on the back of the camera. As soon as the power adapter is connected to the camera, the LED will turn green.
Section 1 - Product Overview Hardware Installation Connect the Ethernet Cable Connect an Ethernet cable to the network cable connector located on the Network Camera’s back panel and attach it to the network. Attach the External Power Supply Attach the external power supply to the DC power input connector located on the Network Camera’s back panel (labeled DC 12V) and connect it to an AC power outlet. Note: When you have a proper connection, the LED will turn green.
Section 1 - Product Overview The Network Camera comes with a camera stand with a swivel ball screw head that can be attached to the Network Camera bottom socket cavity. Attach the camera stand to the Network Camera and station it for your application. There are holes located in the base of the camera stand allowing the Network Camera to be mounted to the ceiling, or any wall securely.
Section 2 - Installation Software Installation Turn on the computer and Insert the D-Link DCS-3410 Driver CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows® XP. The steps and screens are similar for the other Windows operating systems. Click Setup Wizard If the CD Autorun function does not automatically start on your computer, click Windows Start > Run. In the Run command box type “D:\DCS3410.exe”, where D: represents the drive letter of your CD-ROM.
Section 2 - Installation Click Next to continue. Click Next Click Yes to accept the License Agreement.
Section 2 - Installation To start the installation click Next. Note: The installation may take several minutes to complete.
Section 2 - Installation Click Finish to complete the installation.
Section 3 - Configuration Configuration This section will show you how to configure your new D-Link Network Camera using the Setup Wizard. Setup Wizard Configuration Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu.
Section 3 - Configuration The Setup Wizard will appear and show the MAC address of the DCS-3410 and an IP Address (which may or may not be correct depending on what you have your DCS-3410 connected to). If you have a DHCP server on your network, there will be a valid IP Address displayed here. Click the Wizard button to continue. Note: A DHCP server is a device that supplies the IP address. Enter the admin ID and password. Note: The default Admin ID is admin with the password left blank.
Section 3 - Configuration Select DHCP if you want to obtain a new IP address every time the camera boots up. Click Next Select static IP to use the same IP address at each boot up.
Section 3 - Configuration Click Restart to save your settings and reboot the Network Camera. Click Restart Click the button labeled Link to access the web configuration page. The Setup Wizard will automatically open your web browser to the IP address of the DCS-3410, in this example it is: http://192.198.0.120. Your DCS-3410 may have a different IP Address.
Section 3 - Configuration Web-based Configuration Utility This section will show you how to configure your new D-Link Network Camera using the Web-based Configuration Utility. To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address for your Network Camera (http://192.168.0.120) Note: For example, the address is 192.168.0.120. Your address may differ. Enter Admin for the username and then leave the password blank by default.
Section 3 - Configuration Live Video Camera This section shows your camera’s live video. You may select the available thumbnails for your option of predefined Video Profile, Full Screen mode, and action items of taking Snapshot, Recording, Set Storage Folder, Listen, Talk, and Digital Output. You may also select your language setting using the drop-down menu. You can zoom in and out of the live video image using your mouse. Right-click to zoom out and left-click to zoom in on the image.
Section 3 - Configuration Setup Wizard To quickly configure your Network Camera, click Internet Connection Setup Wizard, or click Manual Internet Connection Setup to manually configure your Network Camera. To quickly configure your Network Camera’s motion detection settings, click Motion Detection Setup Wizard and skip to page 24. If you want to enter your settings without running the wizard, click Manual Motion Detection Setup and skip to page 27.
Section 3 - Configuration Select DHCP if you are unsure which settings to pick. Click Next to continue and skip to page 22. Click Next Select Static IP if your Internet Service Provider has provided you with connection settings, or you wish to set a static address within your home network. Enter the accurate information for your static IP setting. Click Next to continue.
Section 3 - Configuration If you are using PPPoE, select Enable and enter your user name and password, otherwise select Disable and click Next to continue. Click Next If you have a Dynamic DNS account and would like the camera to update your IP address automatically, Select Enable and enter your host information. Click Next to continue. Click Next Enter a name for your camera and click Next to continue.
Section 3 - Configuration Configure the correct time to ensure that all events will be triggered, captured and scheduled at the right time. Click Next to continue. Click Next If you have selected DHCP, you will see a summary of your camera’s settings. Please note down all this information as you will need it for accessing your camera within the network. Click Apply to save your settings. Click Apply If you have selected Static IP, you will see a summary of your camera’s settings.
Section 3 - Configuration Motion Detection Setup Wizard This wizard will guide you through a step-by-step process to configure your new D-Link Camera motion detection functions. Click Next to continue. Click Next This section will allow you to enable or disable motion detection as well as control the sensitivity or your camera’s ability to detect movement. You can select the Drawing Mode to draw or erase the motion area in your window of live video.
Section 3 - Configuration This step allows you to specify how you will receive the events notification of your camera, either via using email or FTP. You will need to enter all the relevant information for your email account or FTP settings. Then, click Next to continue.
Section 3 - Configuration You have completed the Motion Detection Wizard. Click Apply to activate your settings.
Section 3 - Configuration Network Setup Use this section to configure the network connections for you camera. All relevant information must be entered accurately. LAN Settings: Settings for your local area network. DHCP: Select this connection if you have a DHCP server running on your network and would like a dynamic IP address to be updated to your camera automatically.
Section 3 - Configuration User Name: The unique name to your account. You may obtain this information from your ISP. Password: The password to your account. You may obtain this information from your ISP. HTTP Port: The default value is 80. RTSP port: The port number that you use for RTSP streaming to mobile devices, such as mobile phones or PDAs. The default port number is 554.
Section 3 - Configuration Dynamic DNS DDNS (Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem when it has been modified. The user name and password are required when using the DDNS service. Enable DDNS: Click to enable the DDNS function. Server Name: Select your Dynamic DNS provider from the pull down menu or enter the server address manually. Host Name: Enter the host name of the DDNS server.
Section 3 - Configuration Image Setup In this section, you may configure the video image settings for your camera. Preview of the image will be shown in the window of Live Video. Click Save Settings to activate and save your changes. BLC: (Back Light Compensation): When an object is placed in front of bright lights, it is difficult for IP camera to capture the image clearly. Turn on this option will help your camera to capture or see the image of the objects when it is exposed to bright lights.
Section 3 - Configuration Audio and Video You may configure 4 video profiles with different setting for your camera. Hence, you may setup different profiles for your computer and mobile display. In addition, you may also configure your audio (speakers and microphone) setup for your camera. Resolution: This option allows the user to choose the video resolution of the camera between 160x120, 320x240 and 704x480: • QQVGA @ 176x120 - Usually used for only displays of handheld devices.
Section 3 - Configuration Motion Detection Enabling Video Motion will allow your camera to use the motion detection feature. You may also draw out the motion area for the monitoring. Enable Video Check this option to turn on the motion detection feature Motion: for your camera. Sensitivity: Set the measurable difference between two sequential images that would indicate motion.
Section 3 - Configuration Time and Date From this section, you may automatically or manually configure, update and maintain the internal system clock for your camera. Time Zone: Select your time zone from the drop-down menu. Enable Daylight Select this to enable the daylight saving time. Saving: Auto Daylight Select this option so that your camera will configure Saving: the Daylight Saving setting automatically.
Section 3 - Configuration Recording In this section, you can configure and schedule the recording setting for your IP camera. Enable Select this option to enable the recording feature. Recording: Samba Auth: To access your account on the Samba network drive, enter your account or anonymous username and password. Server: The name of your Samba server. Shared Folder: The name of the shared folder used for recording.
Section 3 - Configuration Snapshot Enable the Snapshot feature so that your camera can take snaphots and send it to your email address or FTP server. Enable Snapshot: Enable or disable snapshot event. Trigger Event: Select one or more than one of the events such as Motion Detection, D/I Signal 1 and D/I Signal 2 for the source that triggers the action. E-mail Address: Select this option if you want to receive snapshot images in your e-mail.
Section 3 - Configuration Digital Output You may enable the Digital Output (DO) feature and configure the source of event for your camera. Enable D/O This enables the D/O to send a signal when there is a signal: triggered event. Trigger Event: You can choose from one or up to three events, such as Motion Detection, D/I Signal 1, and D/I Signal 2 for the sources of the triggered events.
Section 3 - Configuration RS-485 You may configure the RS-485 settings or communication specifications (baud rate, data bit, stop bit, and parity bit) for your camera. RS-485 is a serial communication method for computers and devices. For your camera, RS-485 is used to control a PAN/TILT device, such as an external camera enclosure to perform PAN and TILT movement.
Section 3 - Configuration Maintenance Device Management You may modify the name and administrator’s password of your camera, as well as add and manage the user accounts for accessing the camera. You may also use this section to create the unique name and configure the OSD setting for your camera. Admin password Set a new password for the administrator’s account. setting: Add user account: Add new user account. User name: The user name for the new account. Password: The password for the new account.
Section 3 - Configuration Backup and Restore In this section, you may backup, restore and reset the settings as well as reboot your camera. Save To Local Hard You may save and document your current configuration Drive: settings into your computer. Local From Local Locate a pre-saved configuration by clicking Browse and Hard Drive: then restore the pre-defined settings to your camera by clicking Load Configuration.
Section 3 - Configuration Firmware Upgrade Your current firmware version and date will be displayed on your screen. You may go to the D-Link Support Page to check for the latest firmware version available. To upgrade the firmware on your DCS-3410, please download and save the latest firmware version from the D-Link Support Page to your local hard drive. Locate the file on your local hard drive by clicking the Browse button. Then, open the file and click the “Upload” button to start the firmware upgrade.
Section 3 - Configuration Status Device Info This page displays all the details information about your device and network connection.
Section 3 - Configuration Logs This page displays the log information of your camera. You may also download the information by clicking Download.
Section 3 - Configuration Help D-Link DCS-3410 User Manual 43
Section 4 - D-ViewCam Installation D-ViewCam Installation D-ViewCam software is included for the administrator to manage up to 32 D-Link IP cameras remotely. You may now use the software to configure all the advanced settings for your cameras. D-ViewCam is a comprehensive management tool for IP surveillance. Insert the CD-ROM into the CD-ROM drive. A menu screen will appear as shown below. Click D-ViewCam D-ViewCam provides English, Traditional Chinese and Simplified Chinese language versions.
Section 4 - D-ViewCam Installation Click Next to continue. Click Next Click Browse if you would like to choose a specific folder for the installation, otherwise click Next to continue.
Section 4 - D-ViewCam Installation Click Next to start the installation. Note: The D-ViewCam installation process may take several minutes to complete. Click Next Click Finish to complete the installation.
Section 4 - D-ViewCam Installation Add a Camera This section will show you how to start and add a camera to the D-ViewCam system. To start D-ViewCam, select Start > All Programs > D-Link > D-Link D-ViewCam. Enter Admin as the default user name and leave the password blank. Click / OK to log into the system and access the Add Camera Wizard. Note: Please refer to page 51 in the D-ViewCam user manual to change your password.
Section 4 - D-ViewCam Installation Welcome to the Add Camera Wizard. Use this wizard to add your cameras to the D-ViewCam system. Note: Use the left or right arrow to navigate the wizard. Click / Next to continue.
Section 4 - D-ViewCam Installation Choose which method to add your camera(s). You can choose Auto Discovery to automatically search for your camera(s), or choose Add Manually to add your camera(s) via the camera’s IP address. Click Next to continue. If you choose Auto Discovery, the system will search all available cameras that are located on the same LAN with same subnet. The system will place all the cameras under the default map called My Map. Click Next to continue.
Section 4 - D-ViewCam Installation D-ViewCam shows the detected IP camera(s) information. You can choose and schedule the recording for each camera. • 24/7 Continuous Recording: Continuously recording 24 hours a day, 7 days a week. • 24/7 Motion Detection Recording: Continuously monitoring but ONLY recording when motion is detected. • Office Hours Only: Continuously monitoring during office hours (08:00 AM to 06.00 PM) and ONLY recording when motion is detected.
Section 4 - D-ViewCam Installation Select Yes to add other camera(s), or select No if you have no additional camera(s) to be added. Click Next to continue. The Add Camera wizard is now complete. Click Close to access the D-ViewCam’s main screen. Your D-ViewCam Installation is Complete! Note: Please refer to the D-ViewCam user manual for information about using D-ViewCam.
Section 5 - Troubleshooting Troubleshooting 1. What is an Network Camera? The Network Camera is a stand-alone system connecting directly to an Ethernet or Fast Ethernet network. It differs from a conventional PC Camera, the Network Camera is an all-in-one system with built-in CPU and Web-based solutions providing a low cost solution that can transmit high quality video images for monitoring.
Section 5 - Troubleshooting 9. Can the DCS-3410 be installed and work if a firewall exists on the network? If a firewall exists on the network, port 80 is open for ordinary data communication. The DCS-3410 uses port 5002 for streaming audio and port 5003 for streaming video. These ports (or the ports you specify from the Advanced Tab in the Configuration screen if you change the default ports) need to be opened on the firewall. 10.
Section 5 - Troubleshooting 13. The images appear to be of poor quality, how can I improve the image quality? Make sure that your computer’s display properties are set above 256 colors. Using 16 or 256 colors on your computer will produce dithering artifacts in the image, making the image appear to be of poor quality. The configuration on the Network Camera image display is incorrect.
Appendix A - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter.
Appendix A - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® XP - Click on Start > Control Panel > Network Connections. Windows® 2000 - From the desktop, right-click My Network Places > Properties. Step 2 Right-click on the Local Area Connection which represents your D-Link network adapter and select Properties.
Appendix B - Technical Specifications Technical Specifications Video Codec MPEG4 / MJPEG MIC 42dB +/- 3dB, Omni-directional Audio Codec GSM-AMR: 5.15kbps, ADPCM: 8Kbps PoE Supported IEEE 802.
Appendix B - Technical Specifications Networking Protocol • IPV4, ARP, TCP, UDP, ICMP • DHCP Client • NTP Client • DNS Client • DDNS Client • SMTP Client • FTP Client • HTTP Server • Samba Client • PPPoE • RTP • RTSP • RTCP • 3GPP Ethernet 10/100M BaseT Fast Ethernet auto negotiation Video Algorithm Supported • MPEG4/MJPEG dual format compression simultaneously • JPEG for still image Features • Adjustable image size and quality • Time stamp and text overlay • Three configurative motion detection windows
Appendix B - Technical Specifications S/N ratio 42dB +/- 3dB, Omni-directional OS Support Device Windows 2000 / Windows XP / Windows Vista / 3GPP Mobile Phone Utility Windows 2000 / Windows XP / Windows Vista Physical Environment Power • 12V 1.
Appendix C - Contacting Technical Support Contacting Technical Support U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. Before you contact technical support, please have the following ready: • Model number of the product (e.g. DCS-3410) • Hardware Revision (located on the label on the bottom of the Network Camera (e.g. rev A1)) • Serial Number (s/n number located on the label on the bottom of the Network Camera).
Appendix D - Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Appendix D - Warranty Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation.
Appendix D - Warranty • The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to DLink Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that are lost in transit to D-Link.
Appendix D - Warranty Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS T
Appendix D - Warranty FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication.
Appendix D - Warranty For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link office. Industry Canada Notice: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Appendix E - Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.
