Owners manual

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
53
vlan OUTER-VLAN
(Optional) Specifies the outer VLAN ID.
any
Specifies to use any source MAC address, any destination MAC
address, any source IP address, or any destination IP address.
host SRC-MAC-ADDR
Specifies a specific source host MAC address.
SRC-MAC-ADDR SRC-MAC-
WILDCARD
Specifies a group of source MAC addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The bit
corresponding to bit value 0 will be checked.
host DST-MAC-ADDR
Specifies a specific destination host MAC address.
DST-MAC-ADDR DST-MAC-
WILDCARD
Specifies a group of destination MAC addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The bit
corresponding to the bit value 0 will be checked.
PROTOCOL
(Optional) Specifies the IP protocol ID. Enter the following keywords:
eigrp, esp, gre, igmp, ospf, pim, vrrp, pcp, and ipinip.
host SRC-IP-ADDR
Specifies a specific source host IP address.
SRC-IP-ADDR SRC-IP-
WILDCARD
Specifies a group of source IP addresses by using a wildcard bitmap.
The bit corresponding to the bit value 1 will be ignored. The bit
corresponding to the bit value 0 will be checked.
host DST-IP-ADDR
Specifies a specific destination host IP address.
DST-IP-ADDR DST-IP-
WILDCARD
Specifies a group of destination IP addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The bit
corresponding to the bit value 0 will be checked.
precedence PRECEDENCE
(Optional) Specifies that packets can be filtered by precedence level,
as specified by a number from 0 to 7.
tos TOS
(Optional) Specifies that packets can be filtered by type of service
level, as specified by a number from 0 to 15.
dscp DSCP
(Optional) Specifies the matching DSCP code in IP header. The range
is from 0 to 63, or select the following DSCP name: af11 - 001010,
af12 -001100, af13 - 001110, af21 - 010010, af22 - 010100, af23 -
010110, af31 - 011010, af32 - 011100, af33 - 011110, af41 - 100010,
af42 - 100100, af43 - 100110, cs1 - 001000, cs2 - 010000, cs3 -
011000, cs4 - 100000, cs5 - 101000, cs6 - 110000, cs7 - 111000,
default - 000000, ef – 101110.
lt PORT
(Optional) Specifies to match if less than the specified port number.
gt PORT
(Optional) Specifies to match if greater than the specified port number.
eq PORT
(Optional) Specifies to match if equal to the specified port number.
neq PORT
(Optional) Specifies to match if not equal to the specified port number.
range MIN-PORT MAX-PORT
(Optional) Specifies to match if fall within the range of ports.
TCP-FLAG
(Optional) Specifies the TCP flag fields and the specified TCP header
bits called ack (acknowledge), fin (finish), psh (push), rst (reset), syn
(synchronize), or urg (urgent).
fragments
(Optional) Specifiese the packet fragment’s filtering.
time-range PROFILE-NAME
(Optional) Specifies the name of time period profile associated with the
access list delineating its activation period.
ICMP-TYPE
(Optional) Specifies the ICMP message type. The valid number for the
message type is from 0 to 255.
ICMP-CODE
(Optional) Specifies the ICMP message code. The valid number for the
message code is from 0 to 255.