Owners manual

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
58
[SEQUENCE-NUMBER] {permit | deny} {esp | pcp | sctp | protocol-id PROTOCOL-ID} {any | host
SRC-IPV6-ADDR | SRC-IPV6-ADDR/PREFIX-LENGTH} {any | host DST-IPV6-ADDR | DST-IPV6-
ADDR/PREFIX-LENGTH} [fragments] [dscp VALUE] [flow-label FLOW-LABEL] [time-range
PROFILE-NAME]
[SEQUENCE-NUMBER] {permit | deny} {any | host SRC-IPV6-ADDR | SRC-IPV6-ADDR/PREFIX-
LENGTH} [any | host DST-IPV6-ADDR | DST-IPV6-ADDR/PREFIX-LENGTH] [fragments] [dscp
VALUE] [flow-label FLOW-LABEL] [time-range PROFILE-NAME]
Standard IPv6 Access List:
[SEQUENCE-NUMBER] {permit | deny} {any | host SRC-IPV6-ADDR | SRC-IPV6-ADDR/PREFIX-
LENGTH} [any | host DST-IPV6-ADDR | DST-IPV6-ADDR/PREFIX-LENGTH] [time-range
PROFILE-NAME]
no SEQUENCE-NUMBER
Parameters
SEQUENCE-NUMBER
Specifies the sequence number. The range is from 1 to 65535. The
lower the number is, the higher the priority of the permit/deny rule.
any
Specifies any source IPv6 address or any destination IPv6 address.
host SRC-IPV6-ADDR
Specifies a specific source host IPv6 address.
SRC-IPV6-ADDR/PREFIX-
LENGTH
Specifies a source IPv6 network.
host DST-IPV6-ADDR
Specifies a specific destination host IPv6 address.
DST-IPV6-ADDR/PREFIX-
LENGTH
Specifies a destination IPv6 network.
tcp, udp, icmp, esp, pcp ,sctp
Specifies the Layer 4 protocol type.
dscp VALUE
(Optional) Specifies the matching traffic class value in IPv6 header.
The range is from 0 to 63, or select the following DSCP name: af11 -
001010, af12 -001100, af13 - 001110, af21 - 010010, af22 - 010100,
af23 - 010110, af31 - 011010, af32 - 011100, af33 - 011110, af41 -
100010, af42 - 100100, af43 - 100110, cs1 - 001000, cs2 - 010000,
cs3 - 011000, cs4 - 100000, cs5 - 101000, cs6 - 110000, cs7 - 111000,
default - 000000, ef – 101110.
lt PORT
(Optional) Specifies to match if less than the specified port number.
gt PORT
(Optional) Specifies to match if greater than the specified port number.
eq PORT
(Optional) Specifies to match if equal to the specified port number.
neq PORT
(Optional) Specifies to match if not equal to the specified port number.
range MIN-PORT MAX-PORT
(Optional) Specifies to match if fall within the range of ports.
PROTOCOL-ID
(Optional) Specifies the protocol ID. The valid value is from 0 to 255.
ICMP-TYPE
(Optional) Specifies the ICMP message type. The valid number of the
message type is from 0 to 255.
ICMP-CODE
(Optional)Specifies the ICMP message code. The valid number of the
code type is from 0 to 255.
ICMP-MESSAGE
(Optional) Specifies the ICMP message. The following pre-defined
parameters are available for selection: beyond-scope, destination-
unreachable, echo-reply, echo-request, erroneous_header, hop-limit,
multicast-listener-query, multicast-listener-done, multicast-listener-
report, nd-na, nd-ns, next-header, no-admin, no-route, packet-too-big,