D-Link™ DGS-3100 SERIES GIGABIT STACKABLE MANAGED SWITCH User Manual V2.
Information in this document is subject to change without notice. © 2007 D-Link Computer Corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of D-Link Computer Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of D-Link Computer Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation.
Table of Contents PREFACE..................................................................................................................................................................I System Overview .................................................................................................................................................................. ii Viewing the Device...........................................................................................................................
Defining SNMP Views ................................................................................................................................................... 46 Defining SNMP Groups.................................................................................................................................................. 47 Defining SNMP Users.....................................................................................................................................................
Viewing LLDP Local Port Information ........................................................................................................................ 102 Viewing LLDP Remote Port Information ..................................................................................................................... 104 CONFIGURING QUALITY OF SERVICE ........................................................................................................... 109 Understanding QoS ...............................
DEFINING ACCESS PROFILE LISTS................................................................................................................ 171 ACL Configuration Wizard............................................................................................................................................... 172 Defining Access Profile Lists............................................................................................................................................
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Preface This preface provides an overview to the guide, and includes the following sections: i System Overview Viewing the Device Device Management Methods User Guide Overview Intended Audience Notes, Notices, and Cautions Safety Cautions General Precautions for Rack-Mountable Products
DGS-3100 Series Gigabit Stackable Managed Switch User Manual System Overview The DGS-3100 series and the DGS-3100-24TG Gigabit Ethernet Switches enhance networks by providing a powerful switch that eliminates network bottlenecks, enabling network administrators to fine tune network configurations. The DGS-3100 series and the DGS-3100-24TG are perfect for departmental and enterprise connections, and are ideal for backbone and server connections.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Device Management Methods The DGS-3100 series and DGS-3100-24TG provide different methods for managing the device including: Web Based Management Interface SNMP-Based Management Command Line Console Web Based Management Interface Once the device is installed, network mangers can configure the switch, monitor the LED panel, and display statistics graphically via a web browser, including: Netscape Navigator (version 7.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your device. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Safety Cautions Use the following safety guidelines to ensure your own personal safety and to help protect your system from potential damage. Throughout this safety section, the caution icon ( ) is used to indicate cautions and precautions that you need to review and follow. To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment, observe the following precautions.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual When connecting or disconnecting power to hot-pluggable power supplies, if offered with your system, observe the following guidelines: – Install the power supply before connecting the power cable to the power supply. – Unplug the power cable before removing the power supply. – If the system has multiple sources of power, disconnect power from the system by unplugging all power cables from the power supplies.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual CAUTION: The system chassis must be positively grounded to the rack cabinet frame. Do not attempt to connect power to the system until grounding cables are connected. Completed power and safety ground wiring must be inspected by a qualified electrical inspector. An energy hazard will exist if the safety ground cable is omitted or disconnected.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 1 GETTING STARTED To begin managing the device, simply run the browser installed on the management station and point it to the IP address defined for the device. For example; http://123.123.123.123. Please note that the proxy for session connection should be turned off. NOTE: The Factory default IP address for the Switch is 10.90.90.90.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Accessing the Boot/Startup Menu Functions The following configuration functions are performed from the Boot (Startup) menu: Downloading Software Set Terminal Baud-Rate Defining Stacking Units To display the Startup menu: 1. During the boot process, after the first part of the POST is completed press Ctrl+shift+ (-) within 2 seconds after the following message is displayed: Autoboot in 2 seconds –press RETURN or Esc.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual The following prompt is displayed: Set new device Baud rate: _ 2. Press Enter to apply changes. Defining Stacking Units Use the Stack menu option to display the current stack unit ID list and define an alternative unit ID (stack membership number). Unit ID 0 is allocated for auto-numbering, which is the factory default. Refer to Managing Stacking for further reference. To access the stack menu: 1. On the Startup menu, press “3”.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Using the Web-Based User Interface This section contains information on starting the D-Link Embedded Web Interface. To access the D-Link user interface: 1. Open an Internet browser. Ensure that pop-up blockers are disabled. If pop-up blockers are enabled, edit, add, and device information messages may not open. 2. Enter the device IP address in the address bar and press Enter.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Understanding the D-Link Embedded Web Interface The D-Link Embedded Web Interface Device Information Page contains the following information: View Description Tree View Displays the different system features, and configuration options. Zoom View Located at the top of the home page, the port LED indicators provide a visual representation of the ports on the D-Link front panel.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual View Description the Switch's ports and expansion modules, showing port activity, duplex mode, or flow control, depending on the specified mode. Various areas of the graphic can be selected for performing management functions, including port configuration 5 Device Application Buttons Provides access to the device logout, and provides information about the Safe Guard mode currently enabled on the device.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Using the Tool Menu The tool menu contains menu options for: Displaying the Stack Status Locating Devices Backing up and Restoring Configuration Files Resetting the Device Downloading the Firmware Rebooting the System Displaying the Stack Status The Stacking Information Page provides specific information for stacked devices. For more information regarding the stacking setup, see Managing Stacking section.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Backing up and Restoring Configuration Files The Config Backup and Restore Page contains fields for downloading and uploading the configuration file from the device through HTTP or TFTP server. To back up and restore configuration files: 1. Click > Config Backup & Restore. The Config Backup and Restore Page opens.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. 3. Select HTTP or TFTP field. Define the selected server method fields. To backup files, click . To restore files, click . Resetting the Device The Factory Reset Page restores the factory defaults. To restore the device to the factory default settings: 1. Click > Reset. The Factory Reset Page opens: Figure 1-4 Factory Reset Page 2. 9 Click is updated. .
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Downloading the Firmware The ‘Firmware Download’ web page is used to download the firmware files that will be used to manage the device. NOTE: Firmware version 1.x.x supports 4 SKUs od DGS-3100 series: DGS-3100-24, DGS-310024P, DGS-3100-48 and DGS-3100-48P, Firmware version 2.x.x supports in addition the 5th SKU: DGS-3100-24TG. Firmware version 2.x.x includes as well additional features comparing to version 1.x.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual The Firmware Download Page contains the following fields: Field Description HTTP Download Indicates that the Firmware file is downloaded via an HTTP server. Unit — Indicates if the Firmware file is downloaded to a specific stacking member or to All stacking members. File — Indicates the Firmware file that is downloaded to the stack or specific device. TFTP Download Indicates that the Firmware file is downloaded via a TFTP server.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Rebooting the System The System Reboot Page provides a method for selecting one, or all of the units to be rebooted. To reboot the system: 1. Click > System Reboot. The System Reboot Page opens: Figure 1-6 System Reboot Page The System Reboot Page contains the Select Unit to Reboot field. The possible values are: Value Description All Reboots all stacking members. 01 - 06 Reboots the specific stack member. 2. 3.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Using the Web System Components The following table contains information regarding the list of buttons: Component Name Description Activate Activates field commands Add Adds selected items ALL Selects all Apply Applies field settings Backup Evokes backup Cancel Cancels settings Clear Clears selected settings and fields Clear All Clears all settings and fields Delete Deletes selected fields Delete VID Deletes VLAN Identificat
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2 CONFIGURING BASIC CONFIGURATION This section contains information for viewing device information, defining IP addresses, managing stacking, defining port parameters, configuring system user accounts, configuring and managing system logs, defining the system time, and configuring SNMP system management.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Device Information The Device Information Page contains parameters for configuring general device information, including the system name, location, and contact, the system MAC Address, System Up Time, and MAC addresses, and both software, boot, and hardware versions. In addition the Device Information Page provides shortcuts to device feature pages. To define the general system information: Click DGS-3100-xx in the Tree View.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description MAC Address Displays the MAC address assigned to the device. IP Address Displays the IP address assigned to the device. Subnet Mask Displays the subnet mask assigned to the device. Default Gateway Displays the device default gateway assigned to the device. Login Timeout (minutes) Indicates the amount of time after which if no user activity occurs, the device times out. The default is 10 minutes.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining System Information The System Information Page provides device information about specific stacking members. To view system information: 1. Click Configuration > System Information. The System Information Page opens: Figure 2-2 System Information Page The System Information Page contains the following fields: Field Description Unit ID Displays the stack unit ID.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining IP Addresses The IP Address Page contains fields for assigning IP addresses. Packets are forwarded to the default IP when frames are sent to a remote network via the Default Gateway. The configured IP address must belong to the same IP address subnet of one of the IP interfaces. The Dynamic Host Configuration Protocol (DHCP) assigns dynamic IP addresses to devices on a network.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Managing Stacking Stacking enhances network flexibility by building virtual switches with more ports then are available in a single device. Stacks are managed by stacking member which called Stack Master., All other stacking members serve as ports only.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Unit ID assignments or modifications are effective only during system initialization, and do not occur during the system uptime. Stacking members do not have to be numbered in sequence, and can be interconnected, as long as each stacking has a unique ID, and at least, one stacking member serves as the Stack Master. Assigning Unit IDs Each stacking member has an assigned unique Unit ID.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual If one of the master enabled stacking members in the stack was set to Force Master by the system administrator (through the GUI – Stacking Master selector), that master enabled stacking member is the Stack Master. Stacking members which are defined as Force Master stacking members are manually selected as the Stack Master. Only a master enabled stacking member can be selected as the Force Master.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Allocating Unit IDs/Resolving Unit ID Conflicts Once the Stack Master is elected, it allocates the Unit IDs to the stacking members that do not have a Unit ID. Stacking members that do not have a Unit ID operate in the Factory Default mode. In addition, the stack Master attempts to resolve all duplicate Unit IDs occurrences among stacking members. The Stack Master reallocates the duplicate Unit ID if there are available Unit IDs.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Building Stacks – Quick Start The DGS-3100 series supports the following stacking scenarios: Building a new stack from scratch Increasing the stack by adding units to an existing stack This section contains the following topics: Stack Resiliency Managing a Self-Ordered Stack Managing a New Manually Ordered Stack Stack Resiliency Topologies of stack can be either Ring or Chain.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual This section contains the following topics: Building New Manually Ordered Stacks Adding Stacking Members to an Existing Manually Ordered Stack Building New Manually Ordered Stacks To build new a self ordered stack: 1. Connect the units physically through the stacking ports. 2. Turn on the units, one at a time. 3.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual – If the new stacking member has a Unit ID of 1 or 2, i.e. the stacking member is a master enabled unit, the new stacking member initiates the Master Election process. However, since the running Stack Master has a longer up-time, it remains the Stack Master and the new stacking member does not become a new Stack Master.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Unit ID 1, and serving as the stack Backup master, while the already running stacking member with Unit ID 2 remains the active Stack Master. The Stack Master performs Unit ID Allocation and Conflict Resolution process. – If the new stacking member is in the Factory Default mode, the new stacking member is assigned the lowest available Unit ID by the Stack Master.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual – If the Stack Master remains in this sub-group, the behavior is the same as described above. If the Backup Master remains in this sub group the behavior is the same as described in0 - Replacing a Failed Stack Master . NOTE: If a stack is divided into two parts with one section which containing the Stack Master, and the other section - Backup Master was operate.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Merging Stacks This example assumes that the user would like to merge two working stacks. This creates one stack from two separate stacks. There are two scenarios: If new stacking members are powered down during insertion and then powered up This is identical to insert stacking members into a running stack, see Replacing Failed Stacking-Members in a Running Stack.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual A running stacking member group is added to an existing stack, assuming each one of the stack groups has an elected Stack Master. The total of existing stacking members and new stacking members exceeds the maximum allowed number of stacking members in a stack, which is 6 stacking members: – Master Detection and Master Election processes determine the master out of one of two combined stacking groups.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Stacking The Stacking Settings Page allows network managers to execute force master and to change each and every unit its own unit ID. To complete the changing process the user need to reboot the unit. 1. Click Configuration > Stacking Settings.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Ports Configuring Port Properties Viewing Port Properties Configuring Port Properties The Port Setting Page contains parameters for configuring port or LAG properties. Gigabit ports operate in full duplex mode only, and take on certain characteristics that are different from the other choices listed. The copper ports also support auto MDI/MDIX for cross over cables. To define port parameters: 1.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Enabled — Indicates that the interface is currently receiving and transmitting traffic. Disabled — Indicates that the interface is currently not receiving and not transmitting traffic. This is the default value. Speed Defines the configured rate for the interface. The port rate determines what speed setting options are available.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Port Properties The Port Description Page allows network managers provide a description of device ports. To define a port description: 1. Click Configuration > >Port Configuration > Port Description. The Port Description Page opens: Figure 2-6 Port Description Page The Port Description Page contains the following fields: Field Description Unit Defines the stacking member for which the port settings are displayed.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual ARP Settings The Address Resolution Protocol (ARP) converts IP addresses into physical addresses and maps the IP address to a MAC address. ARP allows a host to communicate with other hosts only when the IP addresses of its neighbors are known. To define ARP information: 1. Click Configuration > ARP Settings.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring User Accounts User accounts including user passwords and access rights are defined on the User Accounts Page. To define user account information: 1. Click Configuration > User Accounts. The User Accounts Page opens: Figure 2-8 User Accounts Page The User Accounts Page contains the following fields: Field Description User Name Defines the user name. The user name can contain up-to 15 characters.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual To edit the User Accounts Page: 1. Select a name on the User List. 2. Click 3. Define the value. 4. Click . . The new access rights are saved, and device is updated. To delete a User Accounts Page entry: 1. Select an entry. 2. Click . The user account is deleted, and the device is updated.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Managing System Logs System Logs record and manage events and report errors and informational messages. Event messages have a unique format, as per the Syslog protocols recommended message format for all error reporting. For example, Syslog and local device reporting messages are assigned a severity code, and include a message mnemonic, which identifies the source application generating the message.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual To delete a log entry: 1. Select the entry. 2. Click . The entry is deleted, and the device is updated.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring SNTP The device supports the Simple Network Time Protocol (SNTP). SNTP assures accurate network device clock time synchronization up to the millisecond. Time synchronization is performed by a network SNTP server. The device operates only as an SNTP client, and cannot provide time services to other systems. The device polls Unicast type servers for the server time. Time sources are established by stratums.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Polling for Time Information SNTP is used to poll time information from SNTP server. Using SNTP enables accurate system clock. The Time Settings Page allows network managers to enable and configure the SNTP time settings on the device. To enable SNTP: 1. Click Configuration > SNTP Settings > Time Settings.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description clock (Military Time) For example, 9:00PM is configured as 21:00:00. 2. 3. Select a time source in the Time Source field. Define the fields. 4. Click . The SNTP settings are defied, and the device is updated. Configuring Daylight Savings Time The TimeZone Settings Page contains fields for defining system time parameters for both the local hardware clock and the external SNTP clock.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Lithuania — From the last weekend of March until the last weekend of October. Luxembourg — From the last weekend of March until the last weekend of October. Macedonia — From the last weekend of March until the last weekend of October. Mexico — From the first Sunday in April at 02:00 to the last Sunday in October at 02:00. Moldova — From the last weekend of March until the last weekend of October.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual To configure the system time: Click Configuration > SNTP Settings > TimeZone Settings. The TimeZone Settings Page opens: Figure 2-11 TimeZone Settings Page The TimeZone Settings Page contains the following fields: Field Description Daylight Savings Time State Defines type of DST enabled on the device. The possible field values are: Disable — Disables DST on the device. This is the default values. Repeating — Enables setting repeating DST.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description From Which Week of the Month Defines which numeric week of the month DST begins. The possible field values are: First — Indicates the first week of a month. Second — Indicates the second week of a month. Third — Indicates the third week of a month. Fourth — Indicates the fourth week of a month. From Day of Week Defines the week day DST starts. The field range is Sunday–Saturday. From Month Defines the month DST starts.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring SNMP Simple Network Management Protocol (SNMP) provides a method for managing network devices. The device supports the following SNMP versions: SNMP version 1 SNMP version 2c SNMP version 3 SNMP v1 and v2c The SNMP agents maintain a list of variables used to manage the device. The variables are defined in the Management Information Base (MIB).
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining SNMP Views SNMP views provide or block access to device features or aspects of features. For example, a view can be defined to show that SNMP view A has included access to Multicast groups, while SNMP view B has excluded access to Multicast groups. Feature access is granted via the MIB name or MIB Object ID. 1. Click Configuration > SNMP Settings > SNMP View Table.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining SNMP Groups The SNMP Group Table Page provides information for creating SNMP groups and assigning SNMP access control privileges to SNMP groups. Groups enable network managers to assign access rights to specific device features or feature aspects. To define SNMP groups: 1. Click Configuration > SNMP Settings > SNMP Group Table.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Notify View Name Defines a Notify view. The Notify view sends traps for the assigned SNMP view. This is applicable for SNMPv3 only. The possible values are: Community/View TestReadView PWriteView PrivateView Security Model Defines the SNMP version attached to the group. The possible field values are: SNMPv1 — Defines SNMPv1 as the security model for the group. SNMPv2 — Defines SNMPv2 as the security model for the group.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining SNMP Users The SNMP User Table Page enables assigning system users to SNMP groups and defining the user authentication method. To assign system users: 1. Click Configuration > SNMP Settings >SNMP User Table. The SNMP User Table Page opens: Figure 2-14 SNMP User Table Page The SNMP User Table Page contains the following fields: Field Description User Name Defines the SNMP user name included in the SNMP user group.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Auth-Protocol by Key Selects the authentication key type used to authenticate users. The possible field values are: MD5 — Defines that users are authenticated via a HMAC-MD5 algorithm key. SHA — Defines that users are authenticated via a HMAC-SHA-96 authentication level key. Key Defines the authentication key for authentication (MD5 – 32 or 64 digits), (SHA – 40 or 70 digits).
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining SNMP Communities Access rights are managed by defining communities, using the SNMP Community Table Page. When the community names are changed, access rights are also changed. SNMP communities are defined only for SNMP v1 and SNMP v2c. To define SNMP communities: 1. Click Configuration > SNMP Settings > SNMP Community Table.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining SNMP Host Table The SNMP Host Table Page contains information for defining filters that determine whether traps are sent to specific host, as well as the trap type sent. To define the SNMP Host Table Page: 1. Click Configuration > SNMP Settings > SNMP Host Table.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual The SNMP Host Table Page contains the following fields: Field Description Host IP Address Defines the IP address to which the traps are sent. SNMP Version Defines the trap type. The possible field values are: SNMPV1 — Indicates that SNMP Version 1 traps are sent. SNMPV2c —Indicates that SNMP Version 2 traps are sent.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining SNMP Engine ID The Engine ID is a unique identifier used for SNMP V3 implementations. This is an alphanumeric string used to identify the SNMP engine on the switch. To define the SNMP Engine ID: 1. Click Configuration > SNMP Settings > SNMP Engine ID. The SNMP Engine ID Page opens: Figure 2-17 SNMP Engine ID Page The SNMP Engine ID Page contains the following fields: Field Description Engine ID Defines the local device Engine ID.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Enabling SNMP Traps The SNMP Configuration Trap Page contains parameters for defining SNMP notification parameters. To enable SNMP notifications: To enable SNMP Traps: 1. Click Configuration > SNMP Settings > SNMP Trap Configuration.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual DHCP Auto Configuration In the DHCP Auto Configuration Page, users can enable or disable automatic download of the latest image and configuration files from the DHCP server. During reboot, if DHCP Auto Configuration is enabled, the device polls the TFTP Server.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Dual Image Services The device contains two software images in its flash memory, one is for reboot and the other one is for backup. When a software download is successfully completed, the new image automatically becomes the new reboot file, unless the user manually configures the other file to be active. In a stacked system, the user can define the active image file for every unit in the stack.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description An “*” indicates that this image file is used for reboot. Version Displays the image file’s version number. Update Time Displays the time and date which the software was saved to the server. Config Firmware Image The Config Firmware Image Page allows users to change each device’s image file. To change the reboot file: 1. Click Configuration > Dual Image Services > Config Firmware Image.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Telnet Setting The Telnet Setting allows users to enable or disable Telnet on the device. To enable or disable Telnet: 1. Click Configuration > Telnet Setting. The Telnet Setting opens: Figure 2-22 Telnet Setting Page The Telnet Setting contains the following fields: Field Description Telnet Setting Defines the Telnet status on the device. The possible values are: 59 Enabled – Enables Telnet. Disabled – Disables Telnet. 2.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 3 CONFIGURING L2 FEATURES This section contains information for enabling and configuring L2 Features.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Enabling Jumbo Frames Jumbo Frame support is designed to enhance Ethernet networking throughput and significantly reduce the CPU utilization of large file transfers like large multimedia files or large data files by enabling more efficient larger payloads per packet. The Jumbo Frame Page allows network managers to enable Jumbo Frames on the device. 1. Click L2 Features > Jumbo Frame. The Jumbo Frame Page opens: Figure 3–1.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring VLANs Understanding IEEE 802.1p Priority Priority tagging is an IEEE 802.1p defined standard function designed to provide a means of managing traffic on networks where many different types of data are transmitted simultaneously. It is intended to alleviate problems associated with the delivery of time-critical data over congested networks.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Term Description Untagging The act of stripping 802.1Q VLAN information out of the packet header. Ingress port A port on a switch where packets are flowing into the switch and VLAN decisions must be made. Egress port A port on a switch where packets are flowing out of the switch, either to another switch or to an end station, and tagging decisions must be made. IEEE 802.1Q (tagged) VLANs are implemented on the switch. 802.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 802.1Q VLAN Tags The figure below shows the 802.1Q VLAN tag. There are four additional octets inserted after the source MAC address. Their presence is indicated by a value of 0x8100 in the EtherType field. When a packet's EtherType field is equal to 0x8100, the packet carries the IEEE 802.1Q/802.1p tag.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Port VLAN ID Tagged packets (carrying the 802.1Q VID information) can be transmitted from one 802.1Q compliant network device to another with the VLAN information intact. This allows 802.1Q VLANs to span network devices (and the entire network, providing all network devices are 802.1Q compliant). Not all network devices are 802.1Q compliant. Such devices are referred to as tag-unaware. 802.1Q devices are referred to as tag-aware.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual the ingress port. If it does not, the packet is dropped. If it has the same VID, the packet is forwarded and the destination port transmits it on its attached network segment. This process is referred to as ingress filtering, and is used to conserve bandwidth within the switch, by dropping packets that are not on the same VLAN as the ingress port at the point of reception.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining VLAN Properties The VLAN Configuration Page provides information and global parameters for configuring and working with VLANs. 1. Click L2 Features > 802.1Q VLAN. The VLAN Configuration Page opens: Figure 3–5. VLAN Configuration Page The VLAN Configuration Page contains the following fields: Field Description VID Defines the VLAN ID. VLAN Name Defines the user-defined VLAN name. The field ranges is 1-32 characters.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 3–6. Add/Edit VLAN Information Page The Add/Edit VLAN Information Page contains the following fields: Field Description VID Defines the VLAN ID. VLAN Name Defines the user-defined VLAN name. The field ranges up to 32 characters. Unit Defines the stacking member for which the VLAN parameters are displayed. Untag Port Defines the interface is an untagged VLAN member. Packets forwarded by the interface are untagged.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring GVRP GVRP timers need to be in the default values on all Layer 2-connected devices. If the GVRP timers are set differently on the Layer 2-connected devices, the GVRP application does not operate successfully. GARP VLAN Registration Protocol (GVRP) is specifically provided for automatic distribution of VLAN membership information between VLAN-aware bridges.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual The GVRP Setting Page contains the following fields: Field Description GRVP Global Setting Defines whether GRVP is enabled on the device. The possible field values are: Enabled — Enables GRVP on the device. Disabled — Disables GRVP on the device. This is the default value. Unit Defines the stacking member’s Unit ID and LAGs for which GVRP parameters are displayed.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Trunking The Trunking Configuration Page contains information for assigning ports to LAGs and defining LAG parameters. To assign ports to LAGs: 1. Click L2 Features > Trunking. The Trunking Configuration Page opens: Figure 3–8. Trunking Configuration Page The Trunking Configuration Page contains the following fields: Field Description Unit Defines the stacking member’s Unit ID for which LAG parameters are displayed.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Notes about Trunking on the DGS-3100 Series DGS-3100 series supports up to 32 LAGs per device (or stack). NOTE: A port must belong to the default VLAN when the user is adding the port to a LAG, After adding the port to the LAG, the LAG itself can be joined to other VLAN. When a port is added to a LAG, the port’s configuration is stopping to be active, this configuration will return to be active only after the port will be removed from the LAG.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Traffic Segmentation The Traffic Segmentation Page enables administrators to force traffic from source ports to bypass the Forwarding Database (FDB), and forward all Unicast, Multicast and Broadcast traffic to the forwarding port,. Forwarding decisions by the forwarding port overwrite those of the protected source port. To define Traffic Segmentation: 1. Click L2 Features > Traffic Segmentation. The Traffic Segmentation Page opens: Figure 3–9.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring LACP LAG ports can contain different media types if the ports are operating at the same speed. Aggregated links can be set up manually or automatically established by enabling LACP on the relevant links. Aggregate ports can be linked into linkaggregation port-groups. Each group is comprised of ports with the same speed. The LACP Port Settings Page contains fields for configuring LACP LAGs. 1. Click L2 features > LACP Port Settings.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining IGMP Snooping When IGMP Snooping is enabled globally, all IGMP packets are forwarded to the CPU. The CPU analyzes the incoming packets and determines the following information: – Which ports want to join which Multicast groups. – Which ports have Multicast routers generating IGMP queries. – Which routing protocols are forwarding packets and Multicast traffic.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Host Timeout Defines the time the host waits to receive a message before timing out. The default time is 260 seconds. The field range is 60-16711450 seconds. Router Timeout Defines the time the Multicast router waits to receive a message before it times out. The default value is 300 seconds. The field range is 1-16711450 seconds. State Indicates if IGMP snooping is enabled on the VLAN.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Click . The IGMP Snooping and Static Router Ports Settings Page opens: Figure 3–12. IGMP Snooping and Static Router Ports Settings Page The IGMP Snooping and Static Router Ports Settings Page contains the following fields: Field Description VLAN ID Specifies the VLAN ID VLAN Name Displays the user-defined VLAN name.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Enable — Enables IGMP Snooping on the VLAN. Disable — Disables IGMP Snooping on the VLAN Querier State Defines the IGMP Querier status on the VLAN. The possible field values are: Enabled — Enables an IGMP Querier on the VLAN. Disabled — Disables an IGMP Querier on the VLAN.. Querier Version Defines the IGMP Querier version on the VLAN. The possible field values are IGMPv2 and IGMPv3. Unit Defines the unit number.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining MLD Snooping Multicast Listener Discovery (MLD) Snooping performs the same function for IPv6 multicast routers as IGMP Snooping does for IPv4 multicast routers. The device supports two versions of MLD Snooping: – MLDv1 Snooping detects MLDv1 control packets and sets up traffic bridging based on IPv6 destination multicast addresses. MLDv1 is equivalent to IGMPv2.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual The MLD Snooping Page contains the following fields: Field Description MLD Snooping Enables or disables MLD Snooping. The possible field values are: Enabled — Enables MLD Snooping on the device. Disabled — Disables MLD Snooping on the device. (This is the default value). VLAN ID Specifies the VLAN ID. VLAN Name Displays the user-defined VLAN name.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 3–14. MLD Snooping & Static Router Ports Settings Page The MLD Snooping & Static Router Ports Settings Page contains the following fields: Field Description VLAN ID Specifies the VLAN ID VLAN Name Displays the user-defined VLAN name. Done Timer (0-16711450 sec) Defines the time interval in seconds after which a port is removed from the Multicast membership group.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Unit Defines the unit number. Static Router Ports Defines the port numbers in the selected unit to be added as static router ports. Ports Displays the unit:port numbers defined as static router ports. Dynamic Router Ports Displays the port numbers in the selected unit learned as dynamic router ports. Ports Displays the unit:port numbers defined as dynamic router ports.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Port Mirroring Switches inherently forward frames to relevant ports only. This creates difficulty when traffic needs to be monitored, either for information gathering (such as statistical analysis, security traces, etc.) or for troubleshooting higher-layer protocol operation. The device supports up to 8 source ports.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Both Defines the port mirroring on both receiving and transmitting ports. None Defines that port mirroring is not applied to the ports. 2. Define the Status, Unit, and Target fields. 3. Click 4. Define the Unit, Tx, and Rx. fields under Source Port Setting. 5. Click table. to activate the Port Mirroring function.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Spanning Tree Spanning Tree Protocol (STP) provides tree topography for any arrangement of bridges, as well as providing a single path between end stations on a network, thus eliminating loops. Loops occur when alternate routes exist between hosts. Loops in an extended network can cause bridges to forward traffic indefinitely, resulting in increased traffic and reducing network efficiency.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Spanning Tree Global Parameters While Classic STP prevents Layer 2 forwarding loops in a general network topology, convergence can take between 30-60 seconds. This time may delay detecting possible loops and propagating status topology changes. Rapid Spanning Tree Protocol (RSTP) detects and uses network topologies that allow a faster STP convergence without creating forwarding loops.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Bridge Priority (0 – 65535) Specifies the selected spanning tree instance device priority. The field range is 0-65535. The default value is 32768. Bridge Max Age (6- 40) Set to ensure old information is not circulated endlessly through redundant paths in the network, preventing the effective propagation of the new information.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining STP Port Settings STP can be set up on a port per port basis. In addition to setting Spanning Tree parameters for use at the switch level, the switch enables configuring groups of ports, in which case each port-group has its own spanning tree and requires some of its own configuration settings. An STP group uses the switch level parameters entered above, with the addition of Port Priority and Port Cost.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Edge Indicates whether the selected port is an edge port. The possible field values are: True — Defines the port as an edge port. Edge ports cannot create loops; however, they can lose edge port status if a topology change creates a potential for a loop. An edge port normally should not receive BPDU packets. If a BPDU packet is received, it automatically loses edge port status.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Multiple Spanning Tree Configuration Identification Multiple Spanning Tree (MSTP) provides various load balancing scenarios by allowing multiple VLANs to be mapped to a single spanning tree instance, providing multiple pathways across the network. For example, while port A is blocked in one STP instance, the same port can be placed in the Forwarding state in another STP instance.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Remove — Indicates that edit type is remove. VID List (1-4094) Displays the VID List. 2. Define the configuration name and revision level. 3. Click 4. 5. Click to an ID row to edit the ID value. Define the new value. 6. Click updated. . .
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description 200,000,000. The default value is automatically set cost, according to its speed. Default port cost: 10Mbps port = 2000000, 100Mbps port = 200000. Gigabit port = 20000, Port-channel = 20000. Priority Defines the interface priority for the specified instance. The default value is 128. Status Indicates whether the port is enabled for the specific instance.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Forwarding and Filtering This section contains information for configuring both Unicast and Multicast filtering, and contains the following topics: Defining Unicast Forwarding Defining Multicast Forwarding Defining Multicast Filtering Defining Unicast Forwarding The Unicast Forwarding Page contains parameters for configuring Unicast entries. 1. Click L2 Features > Forward & Filtering > Unicast Forwarding.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Click 3. Define the values. . 4. Click . The entry is updated, and the device is updated. To delete a FDB table entry: 1. Select the entry. 2. Click . The entry is deleted, and the device is updated. Defining Multicast Forwarding The Multicast Forwarding Page displays the ports and LAGs attached to the Multicast service group in the Ports and LAGs tables. Ports can be added either to existing groups or to new Multicast service groups.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Egress Defines the Egress ports per multicast group. 2. 3. Define the VID, Multicast MAC Address, Unit, and Egress fields. Select either all, or individual ports: – – Click to select all ports as None or Egress; Alternatively, click to select the ports individually. The default is 1-48 None. .The Multicast forwarding settings are applied to the port, and the device is updated. 4. Click To restore the default settings: 1.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual The Multicast Filtering Mode Page contains the following fields: Field Description Unit Defines the stacking unit number to specify a port range, or LAG to specify a LAG range. From Port or From LAG Defines the first port or LAG in a consecutive sequence of ports or LAGs. To Port or To LAG Defines the last port or LAG in a consecutive sequence of ports or LAGs. All Specifies that the filtering mode applies to all ports or LAGs.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring LLDP The Link Layer Discovery Protocol (LLDP) allows troubleshooting and enhancing network management by discovering and maintaining network topologies over multi-vendor environments. LLDP discovers network neighbors by standardizing methods for network devices to advertise themselves to other systems, and to store discovered information.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field LLDP Status Description Specifies the LLDP status on the device. The possible field values are: Enabled — Enables LLDP on the device. This is the default. Disabled — Disables LLDP on the device. LLDP Forward Status Specifies the LLDP packet forwarding status when LLDP is disabled on the device. The possible field values are: Enabled — Enables LLDP packet forwarding on the device. Disabled — Disables LLDP packet forwarding on the device.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 3–17. LLDP Port Setting Page The LLDP Port Setting Page contains the following fields: Field Unit Description Indicates the stacking member for which the LLDP port settings are defined. From Port Defines the first port in a consecutive sequence of ports. To Port Defines last port in a consecutive sequence of ports. Notification Specifies whether notification is sent when an LLDP topology change occurs on the port.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining LLDP Basic TLV Settings The LLDP Basic TLVS Setting Page displays LLDP basic TLV port information and contains parameters for configuring LLDP basic TLV port settings. 1. Click L2 Features > LLDP > LLDP Basic TLVS Setting. The LLDP Basic TLVS Setting Page opens: Figure 3–18.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Enabled — Enables the System Capabilities TLV on the port. Disabled — Disables the System Capabilities TLV on the port. 2. Define the Unit, From Port, To Port, Port Description, System Name, System Description and System Capabilities fields. 3. Click . The LLDP basic TLV settings are defined, and the device is updated.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing LLDP Local Port Information The LLDP Local Port Brief Page displays LLDP local port information. 1. Click L2 Features > LLDP > LLDP Local Port Brief. The LLDP Local Port Brief Page opens: Figure 3–20. LLDP Local Port Brief Page The LLDP Local Port Brief Page contains the following fields: Field Unit Description Indicates the stacking member for which the LLDP local port information is displayed. Port Indicates the port number.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Click . The LLDP Local Port Normal Page is displayed. Figure 3–21. LLDP Local Port Normal Page 3. To view the detailed MAC/PHY Configuration Status for the port, click Show Detail. The LLDP Local Misc Detail Information Page is displayed. Figure 3–22.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual The LLDP Local Misc Detail Information Page contains the following fields: Field Unit Description Indicates the stacking member for which the LLDP local detail information is displayed. Port Indicates the port number. Auto-Negotiation Support Indicates the port speed auto-negotiation support status. Auto-Negotiation Enable Indicates the port speed auto-negotiation active status.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Chassis ID Description Displays the chassis identification of the device transmitting the LLDP frame. Port ID Subfype Displays the port ID subtype. For example, IPv4 address. Port ID Displays the port ID (Unit number/Port number) of the port transmitting the LLDP frame.. Port Description Displays the port description. 2. Click . The LLDP Remote Port Normal Page is displayed. Figure 3–24. LLDP Remote Port Normal Page 3.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 3–25. LLDP Management Address Detail Information Page The LLDP Management Address Detail Information Page contains the following fields: Field Port Description Indicates the port number. Address Subtype Displays the managed address subtype. For example, MAC or IPv4 Address Displays the managed address. Interface Subtype Displays the port subtype. 4. Click to return to the LLDP Remote Port Normal Page. 5.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 3–26. LLDP Remote Misc Detail Information Page 6. Click 7. To view the detailed information for unknown TLVs for the entry, click Show Detail. The LLDP Remote Unknown TLVs Detailed Information Page is displayed. to return to return to the LLDP Remote Port Normal Page. Figure 3–27.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual The LLDP Remote Unknown TLVs Detailed Information Page contains the following fields: Field Port Description Indicates the port number. Entry Indicates the entry number. Unknown TLV Type Indicates the unknown TLV type field Unknown TLV Information Bytes Displays the unknown TLV information bytes in hexadecimal format.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 4 CONFIGURING QUALITY OF SERVICE Configuring 1p Priority tagging is an IEEE 802.1p defined standard function designed to provide a means of managing traffic on networks where many different types of data are transmitted simultaneously. It is intended to alleviate problems associated with the delivery of time-critical data over congested networks.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 4-1. Mapping QoS on the Switch The picture above shows the default priority setting for the Switch. Class-3 has the highest priority of the four priority queues on the Switch. In order to implement QoS, the user is required to instruct the Switch to examine the header of a packet to see if it has the proper identifying tag tagged.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Understanding QoS The Switch has four priority queues. These priority queues are labeled as 3 (the highest queue) to 0 (the lowest queue). The eight (0-7) priority tags, specified in IEEE 802.1p are mapped to the Switch's priority tags as follows: Priorities 1 and 2 are assigned to the Switch's Q0 queue. Priorities 0 and 3 are assigned to the Switch's Q1 queue. Priorities 4 and 5 are assigned to the Switch's Q2 queue.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Bandwidth Settings The Bandwidth Control Page allows network managers to define the bandwidth settings for a specified interface. 1. Click QoS > Bandwidth Control. The Bandwidth Control Page opens: Figure 4-2.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 113 2. Define the Unit, From Port, To Port, No Limit and Ingress Rate fields. 3. Click . The bandwidth settings are defined, and the device is updated.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Storm Control Storm control limits the amount of Multicast, Broadcast and Unknown Unicast frames accepted and forwarded by the device. When Layer 2 frames are forwarded, Broadcast, Multicast and Unknown Unicast frames are flooded to all ports on the relevant VLAN. This occupies bandwidth, and loads all nodes on all ports.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Mapping Ports to Packet Priorities The 802.1P Default Priority Page provides traffic classification. by assigning priority values per port. The priority value is assigned when packet arrives to a port with an empty priority tag. 1. Click Qos > 802.1p Default Priority. The 802.1P Default Priority Page opens: Figure 4-4. 802.1P Default Priority Page The 802.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Mapping Priority to Classes (Queues) The 802.1P User Priority Page allows network managers to assign priority tags to classes (queues). If a network manager defines a priority of 01 to Class 3, all packets arriving with an assigned value of 01 are sent to class (queue) 3. The default mapping is: Priority 0. 3 is assigned to Q0. This is the lowest priority queue. Priority 1, 2 is assigned to Q1. Priority 4, 5 is assigned to Q2.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring QoS Scheduling Mechanism The QoS Scheduling Mechanism Page contains fields for defining the QoS scheduling forwarding scheme. To define the QoS scheduling mechanism: 1. Click QoS > QoS Scheduling Mechanism. The QoS Scheduling Mechanism Page opens: Figure 4-6.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Multi-Layer CoS Settings For network administrators wanting to configure Multi Layer CoS settings, implementation in the switch is done via the Access Control List.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 5 SECURITY FEATURES This section contains information for enabling and configuring device security including user accounts. 119 Configuring Safeguard Engine Configuring Trust Host Configuring Port Security Configuring Guest VLANs Configuring Port Authentication 802.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Safeguard Engine The Safeguard Engine Page allows network administrators to set network alarms to protect the CPU from attacks, based on rising and falling threshold levels of Broadcasts and CPU Utilization. The Safeguard mechanism immediately implements Broadcast Storm Control with a low threshold in order to hold the attack and release the CPU resources. To enable the safeguard engine: 1. Click Security > Safeguard Engine.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Trust Host The Trusted Host Page permits network managers to manage the device from remote stations. Network managers can configure up to three remote stations. Ensure that the remote stations are configured with the IP address from which the device is currently being configured to prevent disconnection. To enable Trust Host: 1. Click Security > Trusted Host. The Trusted Host Page opens: Figure 5-2.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Port Security Network security can be increased by limiting access on a specific port only to users with specific MAC addresses. The MAC addresses can be dynamically learned or statically configured. Locked port security monitors both received and learned packets that are received on specific ports. Access to the locked port is limited to users with specific MAC addresses.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Max Learning Addr Indicates the number of MAC addresses that can be learned on the port. 123 2. Define the Unit, From Port, To Port, Max Address (0-64), and Admin State fields. 3. Click Port security is enabled, and the device is updated.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Guest VLANs Guest VLANs provide limited network access to authorized ports. If a port is denied network access via port-based authorization, but the Guest VLAN is enabled, the port receives limited network access. For example, a network administrator can use Guest VLANs to deny network access via port-based authentication, but grant internet access to unauthorized users. To define Guest VLANs: 1. Click Security > Guest Vlan.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Port Authentication 802.1X Port-based authentication authenticates users on a per-port/per mac basis via an external server. Only authenticated and approved system users can transmit and receive data. Ports are authenticated via the RADIUS server using the Extensible Authentication Protocol (EAP). The 802.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual To enable the 802.1X: 1. Click Security > 802.1X Setting. The 802.1X Setting Page opens: Figure 5-5. 802.1X Setting Page The 802.1X Setting Page contains the following fields: Field Description 802.1X Indicates if 802.1X is enabled on the device. The possible field values are: Enabled — Enables 802.1X on the device. Disabled —Disables 802.1X on the device. This is the default value.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description value. Disabled — Disables re-authenticating the port or MAC addresses after the port or MAC address authentication has timed out. Control Indicates the host status. If there is an asterisk (*), the port is either not linked or is down.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual To enable MAC Authentication: 1. Click Security > 802.1X Setting. The 802.1X Setting Page opens: The 802.1X Setting Page contains the following fields: Field Description 802.1X Indicates if 802.1X is enabled on the device. The possible field values are: Enabled — Enables 802.1X (and MAC Authentication) on the device. Disabled —Disables 802.1X on the device. This is the default value.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Disabled — Disables re-authenticating the port or MAC addresses after the port or MAC address authentication has timed out. Control Indicates the host status. If there is an asterisk (*), the port is either not linked or is down.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring MAC Authentication (by using Guest VLAN, 802.1X and Radius pages) This is the sequence of operatons required to configure MAC Authentication in DGS-3100 series. 1. In order to configure a guest VLAN, the user is required to create a VLAN first, in the following example the user creates VLAN 100 via click L2 Features > 802.1Q VLAN. The 802.1Q VLAN page opens: 2.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 131 3. After the ports were assigned to the Guest VLAN, the user needs to configure a Radius Server that will hold the MAC Authentication database. This should be done via click Security > 802.1X > Authentic RADIUS Server page according to the example below. 4. Click Security > 802.1X > 802.1X Setting page: first, 802.1x should be enabled globally and in the port level, 802.1x Control should be configured as ‘ForceAuthorized’.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 5. The second step on Security > 802.1X > 802.1X Setting page will be configuration of the required ports as ‘MAC Based’ authentication (opposite to ‘Port Based’ authentication) 6. The last step on Security > 802.1X > 802.1X Setting page should be setting the port control to ‘Auto’, this will complete the setting of MAC Authentication for the required ports.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining RADIUS Settings Remote Authorization Dial-In User Service (RADIUS) servers provide additional security for networks. RADIUS servers provide a centralized authentication method for management access. The default parameters are user-defined, and are applied to newly defined RADIUS servers. If new default parameters are not defined, the system default values are applied to newly defined RADIUS servers. 1. Click Security > 802.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 4. 5. 6. 7. Define the authentication port in the Authentic Port field. Define the accounting port in the Accounting Port field. Define the authentication and encryption key in the Key field. Reenter the RADIUS Key in the Confirm Key field. 8. Click . To edit the Radius Server list, click current values, which then can be edited. To delete a radius server from the list, click defined, and the device is updated.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining EAP Forwarding Settings Ports use the Extensible Authentication Protocol (EAP) forwarding mechanism when 802.1x authentication is disabled. The Forwarding EAP Page allows the user to enable or disable forwarding EAP packets to an authentication server. 1. Click Security > 802.1X > Forwarding EAP. The Forwarding EAP Page opens: Figure 5-1.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Secure Socket Layer Security Secure Socket Layer (SSL) is a security feature that provides a secure communication path between a host and client through the use of authentication, digital signatures, and encryption.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual The SSL Configuration Settings Page contains the following fields: Field Description SSL Status Indicates if SSL is enable on the device. The possible field values are: Enabled — Indicates SSL is enabled on the device. Disabled — Indicates SSL is disabled on the device. (This is the default value.) Ciphersuite Indicates the Ciphersuite.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Secure Shell Security Secure Shell permits network users to securely login to the network from a remote location over an insecure network. SSH a secure login to remote host computers, a safe method of executing commands on a remote end node, and will provide secure encrypted and authenticated communication between two non-trusted hosts.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 3. Define the SSH global setting port number in the Port (1-65535) field. 4. Click . The SSH configuration is defined, and the device is updated. Defining SSH Algorithm Settings This SSH Algorithm Settings Page allows network administrators to enable a public key for SSH authentication encryption.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual All algorithms are enabled by default. To enable SSH Algorithms: 1. Click Security > SSH > SSH Algorithm Settings. The SSH Algorithm Settings Page opens: Figure 5-90. SSH Algorithm Settings Page The SSH Algorithm Settings Page contains the following fields: Field Description Public key Indicates Publickey SSH User Authentication enabled on the device.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Application Authentication Settings Application Authentication permits network administrators to assign authentication methods for user authentication. For example, console users can be authenticated by Authentication List 1, while Telnet users are authenticated by Authentication List 2. 1. Click Security > Access Authentication Control > Application Authentication Settings.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Authentication Server Hosts The Authentication Server is a remote device connected to the same network as the Client and Authenticator. Users are authenticated using either RADIUS or TACACS+, and must be authenticated by the server before attaining network access. To define the Authentication Server information: 1. Click Security > Access Authentication Control> Authentication Server Host.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 3. Click .The Authentication Host properties are defined, and the device is updated. To edit an authentication, click current values, which then can be edited. adjacent to the relevant IP Address on the list. The Authentication Server To delete an authentication, click settings are defined, and the device is updated. adjacent to the relevant IP Address on the list.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description are: RADIUS — User authentication occurs at the RADIUS server. TACACS+ — The user authentication occurs at the TACACS+ server. None — No user authentication occurs. Local — User authentication occurs at the device level. The device checks the user name and password for authentication. Method 3 Indicates the third method used to authenticate the network user.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Enable Methods Network users must first login to the device on the Enable Method Lists Page. Access as non-administrative users is granted. The Enable Method Lists Page allows network mangers to assign user privileges using authentication methods on the device. Once a user is assigned a normal user level privileges the network user is authenticated and granted network access and configuration privileges.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Method 2 Indicates the second method used to authenticate the network user. The possible field values are: RADIUS — User authentication occurs at the RADIUS server. TACACS+ — The user authentication occurs at the TACACS+ server. None — No user authentication occurs. Local — User authentication occurs at the device level. The device checks the user name and password for authentication.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Local Enable Password The Configure Local Enable Password Page allows network administrators to configure the local enabled password. To define the network Local Enable password: 1. Click Security > Access Authentication Control > Configure Local Enable Password. The Configure Local Enable Password Page opens: Figure 5-15.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 6 MONITORING THE DEVICE This section contains information for view device and packet statistics as well as, viewing IGMP information and MAC address information.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Stacking Information The Stacking Information Page provides specific information for stacked devices. To show the Stacking Information Page: 1. 2. , and from the menu select Show Stack Status. Click Alternatively, click Monitoring > Stacking Information in the Tree View.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing CPU Utilization The CPU Utilization Page contains information about the system’s CPU utilization. 1. Click Monitoring > CPU Utilization. The CPU Utilization Page opens: Figure 6-2. CPU Utilization Page The CPU Utilization Page contains the following fields: Field Description Utilization Displays current CPU utilization by percentage.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Port Utilization The Port Utilization Page contains port utilization information for specific ports. To view port statistics: 1. Click Monitoring > Port Utilization. The Port Utilization Page opens: Figure 6-3. Port Utilization Page The Port Utilization Page contains the following fields: Field Description Unit Defines the unit number. Port Defines the port number. Utilization Displays current CPU utilization by percentage.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Packet Size Information The Packet Size Page displays packets received by the switch, arranged in seven groups and classed by size, to be viewed as either a line graph or a table. 1. Click Monitoring > Packet Size. The Packet Size Page opens: Figure 6-4. Packet Size Page The Packet Size Page contains the following fields: Field Description Unit Defines the unit number. Port Defines the port number.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Received Packet Statistics The Received(RX) Page contains information about packets transmitted through device ports. To view received packet statistics: 1. Click Monitoring > Packets > Received(RX). The Received(RX) Page opens: Figure 6-5. Received(RX) Page The Received(RX) Page contains the following fields: Field Description Unit Displays the stacking member for which the transmitted packet statistics are displayed.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 6. 7. Define the Show/Hide field. To view the graph as a table, click View Table. Viewing UMB_cast Packet Statistics The UMB_cast(RX) Page displays the number of UMB cast (Unicast, Multicast and Broadcast) packets received on the device. 1. Click Monitoring > Packets > UMB_cast(RX). The UMB_cast(RX) Page opens: Figure 6-6.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 3. Click to load the defined parameters. To clear the Unit and Port fields: 1. 2. Click . The fields are cleared. Define the Time Interval and Record Number fields. 3. Click 4. . The selected UMB_Cast (RX) packet analysis is displayed To view the graph as a table, click View Table. Viewing Transmitted Packet Statistics The Transmitted(TX) Page contains information about packets transmitted through device ports.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field 2. Description Packets checked — Displays the total amount of transmitted packets. Define the Unit and Port fields. to load the defined parameters. 3. Click To clear the Unit and Port fields: 1. 2. Click . The fields are cleared. Define the Time Interval and Record Number fields. 3. 4. Click . The transmitted packet graph is updated. To view the graph as a table, click View Table.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing RADIUS Authenticated Session Statistics The RADIUS Authentication Pageprovides RADIUS authentication sessions, including how many sessions were initiated, which ports intimated the authentication sessions, and whether or not the sessions were granted. 1. Click Monitoring > Port Access Control > RADIUS Authentication. The RADIUS Authentication Pageopens: Figure 6-8.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing ARP Table The Browse ARP Table Page provides information regarding ARP VLANs, including which IP address was mapped to what MAC address. To view the ARP table: 1. Click Monitoring > Browse ARP Table. The Browse ARP Table Page opens: Figure 6-9 Browse ARP Table Page The Browse ARP Table Page contains the following fields: Field Description VLAN Name Defines the VLAN for which the ARP mappings are defined.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing MLD Router Ports The Browse MLD Router Port Page displays which ports are connected to MLD routers. A port can be connected to an MLD router either as a static port or as a dynamic port or forbidden port. 1. Click Monitoring > Browse MLD Router Port.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Router Ports The Browse Router Port Page displays which ports are connected to routers. Ports can be connected to routers either as a static port or as a dynamic port. 1. Click Monitoring > Browse Router Port. The Browse Router Port Page opens: Figure 6-11 Browse Router Port Page The Browse Router Port Page contains the following fields: Field Description VID Indicates the VLAN identification.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Session Table The Browse Session Table Page displays information regarding device sessions which were initiated by system Users. To view session table information: 1. Click Monitoring > Browse Session Table. The Browse Session Table Page opens: Figure 6-12 Browse Session Table Page The Browse Session Table Page contains the following fields: Field Description ID Displays the browse session table entry.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing IGMP Group Information The IGMP Snooping Group Page contains vital IGMP group information, including the Multicast Group IP address and the corresponding MAC address through which the IGMP packets passed. 1. Click Monitoring >IGMP Snooping Group.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing MLD Group Information The MLD Snooping Group Page contains vital MLD group information, including the Multicast Group IP address and the corresponding MAC address through which the MLD packets passed. 1. Click Monitoring > MLD Snooping Group.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Dynamic and Static MAC Addresses Packets addressed to destinations stored in either the Static or Dynamic databases are immediately forwarded to the port. The MAC Address Table Page can be sorted by interface, VLAN, or MAC Address, whereas MAC addresses are dynamically learned as packets from sources that arrive at the device. Static addresses are configured manually.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 4. 165 Click . – To view all entries, click – To clear static entries, click – To clear dynamic entries, click – To clear all entries, click – To scroll down the table, click – To scroll up the table, click . . . . The MAC Address Table updates and displays total entries. . .
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing System Log The System Log Page provides information about system logs, including information when the device was booted, how the ports are operating, when users logged in, when sessions timed out, as well as other system information. To view the System Log Page: 1. Click Monitoring > System Log.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 7 MANAGING POWER OVER ETHERNET DEVICES Power over Ethernet (PoE) provides power to devices over existing LAN cabling, without updating or modifying the network infrastructure. Power over Ethernet removes the necessity of placing network devices next to power sources.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining PoE System Information The PoE Port Setting Page contains system PoE information for enabling PoE on the device, monitoring the current power usage, and enabling PoE traps. To enable PoE on the device: 1. Click PoE > PoE Port Setting.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Fields Description Class 2 — Indicates the power consumption is 7W. Class 3 — Indicates the power consumption is 15.4W. Status Indicates the inline power source status. The possible field values are: Normal — Indicates that the power supply unit is functioning. Off — Indicates that the power supply unit is not functioning. Faulty — Indicates that the power supply unit is functioning, but an error has occurred.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Displaying and Editing PoE System Information The PoE System Setting Page displays system PoE information on the device, monitoring the current power usage, and enabling PoE traps. To display system PoE information on the device: 1. Click PoE > PoE System Setting. The PoE System Setting Page opens: Figure 7-2 PoE System Setting Page The PoE System Setting Page contains the following fields: Fields Unit Description Defines the unit.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 8 DEFINING ACCESS PROFILE LISTS Access Control Lists (ACL) allow network managers to define classification actions and rules for specific ingress ports. Packets entering an ingress port with an active ACL are either admitted, denied or subject to Quality of Service action. For example, a network administrator defines an ACL rule that states port number 20 can receive TCP packets, however, if a UDP packet is received, the packet is dropped.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual ACL Configuration Wizard The ACL Configuration Wizard Page provides information for configuring Access Control Lists. The ACL Configuration Wizard Page assists in configuring ACLs intuitively and quickly, and creates ACL profiles and rules automatically. To define ACLs: 1. Click ACL > ACL Configuration Wizard.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Fields Description UDPAll — Specifies a UDP Packets filtering. UDP Source Port — Matches the packet to the UDP Source Port UDP Destination Port — Matches the packet to the UDP Destination Port Action Defines the ACL forwarding action matching the rule criteria. The possible values are: Permit — Forwards packets if all other ACL criteria are met. Deny — Drops packets if all other ACL criteria is met.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Access Profile Lists This section contains the following topics: Adding ACL Profiles Defining Level 2 ACL Defining Level 3 ACL Adding ACL Profiles The ACL Profile List Page provides information for configuring ACL Profiles manually. ACL profiles are attached to interfaces, and define how packets are forwarded if they match the ACL criteria. 1. Click ACL > Access Profile List.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 8-3 Add ACL Profile Page The Add ACL Profile Page contains the following fields: Field Description L2 ACL Defines the ACL profile Layer 2 protocols. The possible values are: Tagged — Defines the profile Layer 2 to match 802.1Q fields in the Layer 2 header. Untagged — Defines the profile Layer 2 to check the Layer 2 header without the 802.1Q fields . L3 ACL Defines the ACL profile Layer 3 protocols.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Level 2 ACL If L2 ACL Tagged is selected, the page updates as follows: Figure 8-4 ACL Profile L2 ACL Tagged Page To define L2 MAC Address ACL profile: 1. Click the MAC Address button.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual The ACL Profile L2 ACL Tagged MAC Address Page contains the following fields: Field Description Source MAC Mask Defines the range of source addresses relative to the ACL rules (0=ignore, 1=check). For example, to set 00:00:00:00:10:XX, use mask FF:FF:FF:FF:FF:00. Destination MAC Mask Defines the range of destination addresses relative to the ACL rules (0=ignore, 1=check). For example, to set 00:00:00:00:10:XX, use mask FF:FF:FF:FF:FF:00. 2.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 8-7 ACL Profile L2 ACL Tagged Ether Type Page 2. Click . The ACL profile is added, and the device is updated. NOTE: A combination of one or several filtering masks can be selected simultaneously. The page updates with the relevant field(s).
DGS-3100 Series Gigabit Stackable Managed Switch User Manual If L2 ACL Untagged is selected, the page updates as follows (without the 802.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual This option defines whether or not the DSCP field is checked for a match. 1. Click the IPv4 DSCP button. The ACL Profile L3 ACL ICMP IPv4 DSCP Page updates to show the following: Figure 8-10 ACL Profile L3 ACL ICMP IPv4 DSCP Page 2. Click . The ACL profile is added, and the device is updated. To define L3 IPv4 Address ACL profile: 1. Click the IPv4 Address button.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual The ACL Profile L3 ACL ICMP IPv4 Address Page contains the following fields: Field 2. 3. Description Source IP Mask Defines the range of source IP addresses, relevant to the ACL rules. (0=ignore, 1=check). For example, to set 176.212.XX.XX, use mask 255.255.0.0 Destination IP Mask Defines the range of destination IP addresses, relevant to the ACL rules. (0=ignore, 1=check). For example, to set 176.212.XX.XX, use mask 255.255.0.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual If L3 ACL IGMP is selected, the page updates as follows: Figure 8-13 ACL Profile L3 IGMP Page 1. Click the IGMP button. The ACL Profile L3 IGMP Selected Page updates to show the following: Figure 8-14 ACL Profile L3 IGMP Selected Page 2. Click . The ACL profile is added, and the device is updated.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual If L3 ACL TCP is selected, the page updates as follows: Figure 8-15 ACL Profile L3 TCP Page To define L3 TCP Port ACL profile: 1. Click the TCP Port button.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual The ACL Profile L3 TCP Port Page contains the following fields: Field Description Source Port Mask Defines the range of source Ports relevant to the ACL rules. (0=ignore, 1=check). For example, to set 0 – 15, set mask of FFF0. Destination Port Mask Defines the range of destination IP addresses, relevant to the ACL rules. (0=ignore, 1=check). For example, to set 0 – 15, set mask of FFF0. 2. 3.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual If L3 ACL UDP is selected, the page updates as follows: Figure 8-18 ACL Profile L3 UDP Page 1. Click the UDP Port button.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Source Port Mask Defines the range of source Ports relevant to the ACL rules. (0=ignore, 1=check). For example, to set 0 – 15, set mask of F. Destination Port Mask Defines the range of destination IP addresses, relevant to the ACL rules. (0=ignore, 1=check). For example, to set 0 – 15, set mask of F. 2. 3. Select Source Port Mask and/or Destination Port Mask. The Mask Generate button is active.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Access Rules Lists The following conditions can be defined as Access Rules: Filter Description Source Port IP Address and Wildcard Mask Filters the packets by the Source port IP address and wildcard mask. Destination Port IP Address and Wildcard Mask Filters the packets by the Source port IP address and wildcard mask. Protocol Filters the packets by the Layer 4 protocol.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual To change ACL rules: 1. Click . The Add Access Rule Page opens: Figure 8-21 Add Access Rule Page (IP based ACL) The Add Access Rule Page contains the following fields: Field Description Profile ID Displays the Profile ID to which the rule is being added to. Source ID Displays the source IP address TCP Source Port Displays The TCP Source Port TCP Flag Mask Indicates if TCP flag mask is active.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Range Name Selects the user-defined time range name to apply to the access rule. 2. Define the Rule Detail fields. 3. Click . The rule is changed, and the device is updated. NOTE: Each Access Profile must create rules with unuque Access IDs, Access IDs canno overlap in two different Access Profiles.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Finding ACL Rules The ACL Finder Page identifies any rule which has been assigned to a specific port. To find ACL rules: 1.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 8-23 Rule Detail Page The Rule Detail Page contains the following fields: Field Description Profile ID Displays the profile ID range. Source MAC Displays the Source MAC range. Destination MAC Displays the destination MAC range. Ether Type Displays if Ether Type is included. Access ID Defines the Access ID Type Displays the profile type (can be MAC based or IP based). VLAN Name Defines the user-defined VLAN name.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Define the Rule Detail fields. 3. Click .
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Time Ranges Time-based ACLs allow users to define Access Control Lists based on time periods. The Time Range Setting Page defines a time range, which can be applied to an ACL rule. To define a time range: 1. Click ACL > Time Range Setting. The Time Range Setting Page opens: Figure 8-24 Time Range Setting Page The Time Range Setting Page contains the following fields: Field Description Range Name Defines the Time Range Name.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Click 3. Click . A confirmation window is displayed . . The entry is deleted. To view or modify Time Range settings: 4. Click . The Time Range Edit Page opens: Figure 8-25 Time Range Edit Page 5. Define the Time Range Edit fields. 6. Click .
DGS-3100 Series Gigabit Stackable Managed Switch User Manual – Add L3 Access Profile with the desired fields. – Go to ‘Access Rule List’ page, create rules for both profiles and apply it on the same port(s) /LAG(s). Now you have on the port(s) /LAG(s) IP Based ACL and MAC Based ACL. NOTE: Adding rules to specific profile will have a unique Access ID in the range 1-240. When the user is adding a rule to different profiles he can’t use the same Access ID for different rules.
DGS-3100 Series Gigabit Stackable Managed Switch User Manual Notes about ACLs capacity in the DGS-3100 Series The user can create up to 15 Access Profiles. The user can configure up to 240 Access IDs, each Access ID is unique i.e. the same Access ID can’t be created from two different Access Profiles. The maximum capacity of DGS-3100 series is 240 rules.
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor. Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
Product Registration Register your D-Link product online at http://support.dlink.com/register/ Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.
LIMITED WARRANTY D-Link provides this limited warranty for its product only to the person or entity who originally purchased the product from D-Link or its authorized reseller or distributor. D-Link would fulfill the warranty obligation according to the local warranty policy in which you purchased our products.
D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software. The Warranty Period shall extend for an additional ninety (90) days after any replacement Software is delivered.
Initial installation, installation and removal of the product for repair, and shipping costs. Operational adjustments covered in the operating manual for the product, and normal maintenance. Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage. Any hardware, software, firmware or other products or services provided by anyone other than D-Link.
may not apply. This limited warranty provides specific legal rights and the product owner may also have other rights which vary from state to state. Trademarks Copyright 2007 D-Link Corporation. Contents subject to change without prior notice. D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective proprietors.
TECHNICAL SUPPORT Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the service period, and warranty confirmation service, during the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone.
Technical Support You can find software updates and user documentation on the D-Link websites. If you require product support, we encourage you to browse our FAQ section on the Web Site before contacting the Support line. We have many FAQ’s which we hope will provide you a speedy resolution for your problem. For Customers within The United Kingdom & Ireland: D-Link UK & Ireland Technical Support over the Internet: http://www.dlink.co.uk ftp://ftp.dlink.co.
Technische Unterstützung Aktualisierte Versionen von Software und Benutzerhandbuch finden Sie auf der Website von D-Link. D-Link bietet kostenfreie technische Unterstützung für Kunden innerhalb Deutschlands, Österreichs, der Schweiz und Osteuropas. Unsere Kunden können technische Unterstützung über unsere Website, per E-Mail oder telefonisch anfordern. Web: http://www.dlink.de E-Mail: support@dlink.de Telefon: +49 (1805)2787 0,12€/Min aus dem Festnetz der Deutschen Telekom.
Assistance technique Vous trouverez la documentation et les logiciels les plus récents sur le site web DLink. Vous pouvez contacter le service technique de D-Link par notre site internet ou par téléphone. Support technique destiné aux clients établis en France: Assistance technique D-Link par téléphone : 0820 0803 03 N° INDIGO - 0,12€ TTC/min* *Prix en France Métropolitaine au 3 mars 2005 Du lundi au samedi – de 9h00 à 19h00 Assistance technique D-Link sur internet : http://www.dlink.
Asistencia Técnica Puede encontrar las últimas versiones de software así como documentación técnica en el sitio web de D-Link. D-Link ofrece asistencia técnica gratuita para clientes residentes en España durante el periodo de garantía del producto. Asistencia Técnica de D-Link por teléfono: +34 902 30 45 45 Lunes a Viernes de 9:00 a 14:00 y de 15:00 a 18:00 Asistencia Técnica de D-Link a través de Internet: http://www.dlink.es/support/ e-mail: soporte@dlink.
Supporto tecnico Gli ultimi aggiornamenti e la documentazione sono disponibili sul sito D-Link. Supporto tecnico per i clienti residenti in Italia D-Link Mediterraneo S.r.L. Via N. Bonnet 6/B 20154 Milano Supporto Tecnico dal lunedì al venerdì dalle ore 9.00 alle ore 19.00 con orario continuato Telefono: 199 400057 URL : http://www.dlink.it/supporto.html Email: tech@dlink.
Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within Benelux for the duration of the warranty period on this product. Benelux customers can contact D-Link technical support through our website, or by phone. Tech Support for customers within the Netherlands: D-Link Technical Support over the Telephone: 0900 501 2007 Monday to Friday 9:00 am to 10:00 pm D-Link Technical Support over the Internet: www.dlink.
Pomoc techniczna Najnowsze wersje oprogramowania i dokumentacji użytkownika można znaleźć w serwisie internetowym firmy D-Link. D-Link zapewnia bezpłatną pomoc techniczną klientom w Polsce w okresie gwarancyjnym produktu. Klienci z Polski mogą się kontaktować z działem pomocy technicznej firmy D-Link za pośrednictwem Internetu lub telefonicznie. Telefoniczna pomoc techniczna firmy D-Link: 0 801 022 021 Pomoc techniczna firmy D-Link świadczona przez Internet: URL: http://www.dlink.
Technická podpora Aktualizované verze software a uživatelských příruček najdete na webové stránce firmy D-Link. D-Link poskytuje svým zákazníkům bezplatnou technickou podporu Zákazníci mohou kontaktovat oddělení technické podpory přes webové stránky, mailem nebo telefonicky Web: http://www.dlink.cz/suppport/ E-mail: support@dlink.cz Telefon: 224 247 503 Telefonická podpora je v provozu: PO- PÁ od 09.00 do 17.
Technikai Támogatás Meghajtó programokat és frissítéseket a D-Link Magyarország weblapjáról tölthet le. Telefonon technikai segítséget munkanapokon hétfőtől-csütörtökig 9.00 – 16.00 óráig és pénteken 9.00 – 14.00 óráig kérhet a (1) 461-3001 telefonszámon vagy a support@dlink.hu emailcímen. Magyarországi technikai támogatás : D-Link Magyarország 1074 Budapest, Alsóerdősor u. 6. – R70 Irodaház 1 em. Tel. : 06 1 461-3001 Fax : 06 1 461-3004 email : support@dlink.hu URL : http://www.dlink.
Teknisk Support Du kan finne programvare oppdateringer og bruker dokumentasjon på D-Links web sider. D-Link tilbyr sine kunder gratis teknisk support under produktets garantitid. Kunder kan kontakte D-Links teknisk support via våre hjemmesider, eller på tlf. Teknisk Support: D-Link Teknisk telefon Support: 800 10 610 (Hverdager 08:00-20:00) D-Link Teknisk Support over Internett: http://www.dlink.
Teknisk Support Du finder software opdateringer og brugerdokumentation på D-Link’s hjemmeside. D-Link tilbyder gratis teknisk support til kunder i Danmark i hele produktets garantiperiode. Danske kunder kan kontakte D-Link’s tekniske support via vores hjemmeside eller telefonisk. D-Link teknisk support over telefonen: Tlf. 7026 9040 Hverdager: kl. 08:00 – 20:00 D-Link teknisk support på Internettet: http://www.dlink.
Teknistä tukea asiakkaille Suomessa: D-Link tarjoaa teknistä tukea asiakkailleen. Tuotteen takuun voimassaoloajan. Tekninen tuki palvelee seuraavasti: Arkisin klo. 9 - 21 numerosta 0800-114 677 Internetin kautta Ajurit ja lisätietoja tuotteista. http://www.dlink.fi Sähköpostin kautta voit myös tehdä kyselyitä.
Teknisk Support På vår hemsida kan du hitta mer information om mjukvaru uppdateringar och annan användarinformation. D-Link tillhandahåller teknisk support till kunder i Sverige under hela garantitiden för denna produkt. Teknisk Support för kunder i Sverige: D-Link Teknisk Support via telefon: 0770-33 00 35 Vardagar 08.00-20.00 D-Link Teknisk Support via Internet: http://www.dlink.
Suporte Técnico Você pode encontrar atualizações de software e documentação de utilizador no site de D-Link Portugal http://www.dlink.pt. A D-Link fornece suporte técnico gratuito para clientes no Portugal durante o período de vigência de garantia deste produto. Suporte Técnico para clientes no Portugal: Assistência Técnica: Email: soporte@dlink.es http://www.dlink.pt/support/ ftp://ftp.dlink.
Τεχνική Υποστήριξη Μπορείτε να βρείτε software updates και πληροφορίες για τη χρήση των προϊόντων στις ιστοσελίδες της D-Link Η D-Link προσφέρει στους πελάτες της δωρεάν υποστήριξη στον Ελλαδικό χώρο Μπορείτε να επικοινωνείτε με το τμήμα τεχνικής υποστήριξης μέσω της ιστοσελίδας ή μέσω τηλεφώνου Για πελάτες εντός του Ελλαδικού χώρου: Τηλεφωνική υποστήριξη D-Link : Τηλ: 210 86 11 114 Φαξ: 210 86 53 172 (Δευτέρα-Παρασκευή 09:00-17:00) e-mail: support@dlink.
Technical Support You can find software updates and user documentation on the D-Link website. Tech Support for customers in Australia: Tel: 1300-766-868 Monday to Friday 8:00am to 8:00pm EST Saturday 9:00am to 1:00pm EST http://www.dlink.com.au e-mail: support@dlink.com.au India: Tel: 1800-222-002 Monday to Friday 9:30AM to 7:00PM http://www.dlink.co.in/support/productsupport.
Technical Support You can find software updates and user documentation on the D-Link website. Tech Support for customers in Egypt: Tel: +202-2919035 or +202-2919047 Sunday to Thursday 9:00am to 5:00pm http://support.dlink-me.com e-mail: amostafa@dlink-me.com Iran: Tel: +98-21-88822613 Sunday to Thursday 9:00am to 6:00pm http://support.dlink-me.com e-mail: support.ir@dlink-me.com Israel: Tel: +972-9-9715701 Sunday to Thursday 9:00am to 5:00pm http://www.dlink.co.il/support/ e-mail: support@dlink.co.
Техническая поддержка Обновления программного обеспечения и документация доступны на Интернет-сайте D-Link. D-Link предоставляет бесплатную поддержку для клиентов в течение гарантийного срока. Клиенты могут обратиться в группу технической поддержки D-Link по телефону или через Интернет. Техническая поддержка D-Link: +495-744-00-99 Техническая поддержка через Интернет http://www.dlink.ru e-mail: support@dlink.
Asistencia Técnica D-Link Latin América pone a disposición de sus clientes, especificaciones, documentación y software mas reciente a través de nuestro Sitio Web www.dlinkla.com El servicio de soporte técnico tiene presencia en numerosos países de la Región Latino América, y presta asistencia gratuita a todos los clientes de D-Link, en forma telefónica e internet, a través de la casilla soporte@dlinkla.
Suporte Técnico Você pode encontrar atualizações de software e documentação de usuário no site da D-Link Brasil www.dlinkbrasil.com.br. A D-Link fornece suporte técnico gratuito para clientes no Brasil durante o período de vigência da garantia deste produto. Suporte Técnico para clientes no Brasil: Telefone São Paulo +11-2185-9301 Segunda à sexta Das 8h30 às 18h30 Demais Regiões do Brasil 0800 70 24 104 E-mail: e-mail: suporte@dlinkbrasil.com.
D-Link 友訊科技 台灣分公司 技術支援資訊 如果您還有任何本使用手冊無法協助您解決的產品相關問題，台灣 地區用戶可以透過我們的網站、電子郵件或電話等方式與D-Link台灣 地區技術支援工程師聯絡。 D-Link 免付費技術諮詢專線 0800-002-615 服務時間：週一至週五，早上8:30到晚上9:00 (不含周六、日及國定假日) 網 站：http://www.dlink.com.tw 電子郵件：dssqa_service@dlink.com.tw 如果您是台灣地區以外的用戶，請參考D-Link網站全球各地 分公司的聯絡資訊以取得相關支援服務。 產品保固期限、台灣區維修據點查詢，請參考以下網頁說明： http://www.dlink.com.
Dukungan Teknis Update perangkat lunak dan dokumentasi pengguna dapat diperoleh pada situs web D-Link. Dukungan Teknis untuk pelanggan: Dukungan Teknis D-Link melalui telepon: Tel: +62-21-5731610 Dukungan Teknis D-Link melalui Internet: Email : support@dlink.co.id Website : http://support.dlink.co.
术 支持 您可以在 D-Link 的官方網站找到產品的軟件升級和使用手冊 办公地址：北京市东城区北三环东路 36 号 环球贸易中心 B 座 26F 02-05 室 邮编: 100013 技术支持中心电话：8008296688/ (028)66052968 技术支持中心传真：(028)85176948 维修中心地址：北京市东城区北三环东路 36 号 环球贸易中心 B 座 26F 02-05 室 邮编: 100013 维修中心电话：(010) 58257789 维修中心传真：(010) 58257790 网址：http://www.dlink.com.
International Offices U.S.A 17595 Mt. Herrmann Street Fountain Valley, CA 92708 TEL: 1-800-326-1688 URL: www.dlink.com Canada 2180 Winston Park Drive Oakville, Ontario, L6H 5W1 Canada TEL: 1-905-8295033 FAX: 1-905-8295223 URL: www.dlink.ca Europe (U. K.) D-Link (Europe) Ltd D-Link House, Abbey Road Park Royal, London NW10 7BX United Kingdom TEL: +44 (0)20 8955 9000 FAX: +44 (0)20 8955 9001 URL: www.dlink.co.
International Offices Registration Card All Countries and Regions Excluding USA Print, type or use block letters. Your name: Mr./Ms _____________________________________________________________________________ Organization: ________________________________________________ Dept.
______________________ ______________________ ______________________ ____________ 230
