D-Link DIR-605 無線寬頻路由器 Wireless N Router 中文快速安裝/設定指南
Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date 1.0 July 31, 2008 Description t 6QEBUFE GPS SFWJTJPO Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
Table of Contents Table of Contents Preface....................................................................................................... i Manual Revisions........................................................................... i Trademarks ...................................................................................... i Product Overview ................................................................................ 1 Package Contents....................................................
Table of Contents DHCPv6 (Stateful) ..........................................................52 DHCPv6 (Stateless)........................................................53 IPv6 over PPPoE (Stateful)...........................................54 IPv6 over PPPoE (Stateless) ........................................56 6 to 4 Tunneling (Stateful) ..........................................58 6 to 4 Tunneling (Stateless) ........................................59 IPv6 in IPv4 Tunneling (Stateful)................
Section 1 - Product Overview Product PackageOverview Contents D-Link DIR-605 Wireless N Router Power Adapter Ethernet Cable CD-ROM Note: Using a power supply with a different voltage rating than the one included with the DIR-605 will cause damage and void the warranty for this product.
Section 1 - Product Overview System Requirements Network Requirements t "O &UIFSOFU CBTFE $BCMF PS %4- NPEFN t *&&& O ESBGU H XJSFMFTT DMJFOUT t &UIFSOFU Computer with the following: t 8JOEPXT®, Macintosh, or Linux-based operating system t "O JOTUBMMFE &UIFSOFU BEBQUFS Web-based Configuration Utility Requirements Browser Requirements: t *OUFSOFU &YQMPSFS PS IJHIFS t .
Section 1 - Product Overview Features t 'BTUFS 8JSFMFTT /FUXPSLJOH - The DIR-605 provides up to 300Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. t $PNQBUJCMF XJUI H %FWJDFT - The DIR-605 is still fully compatible with the IEEE 802.11g standard, so it can connect with existing 802.11g PCI, USB and Cardbus adapters.
Section 1 - Product Overview Hardware Overview C D-Link DIR-605 User Manual ti 4
Section 1 - Product Overview Hardware Overview LEDs D-Link DIR-605 User Manual 5
Section 2 - Installation Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage.
Section 2 - Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Section 2 - Installation Network Diagram D-Link DIR-605 User Manual 8
Section 2 - Installation Connect to Cable/DSL/Satellite Modem If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below: 1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down your computer. 3.
Section 2 - Installation Connect to Another Router If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network: t %JTBCMF 61O1™ t %JTBCMF %)$1 t $IBOHF UIF -"/ *1 BEESFTT UP BO BWBJMBCMF BEESFTT PO ZPVS OFUXPSL 5IF -"/ QPSUT PO UIF SPVUFS DBOOPU accept a DHCP address from your other router. To connect to another router, please follow the steps below: 1.
Section 2 - Installation 6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the Internet port of the D-Link router. :PV NBZ OPX VTF UIF PUIFS -"/ QPSUT UP DPOOFDU PUIFS &UIFSOFU EFWJDFT BOE DPNQVUFST 5P DPOöHVSF ZPVS XJSFMFTT network, open a web browser and enter the IP address you assigned to the router.
Section 2 - Installation Getting Started The DIR-605 includes a Quick Router Setup Wizard CD. Follow the simple steps below to run the Setup Wizard to guide you RVJDLMZ UISPVHI UIF JOTUBMMBUJPO QSPDFTT :PV NBZ NBOVBMMZ DPOöHVSF ZPVS SPVUFS XJUIPVU UIF XJ[BSE 3FGFS UP UIF OFYU QBHF to manually setup your router. Insert the Quick Router Setup Wizard CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows® XP or Vista®.
Section 3 - Configuration Configuration This section will show you how to configure your new D-Link wireless router using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1). Select Admin from the drop-down menu and then enter your password. Leave the password blank by default.
Section 3 - Configuration Internet Connection Setup Wizard Once logged into the web interface of the router, the Setup > Internet page will appear. Click the Internet Connection Setup Wizard button to quickly configure your router using the setup wizard. If you want to enter your settings without running the wizard, click Manual Internet Configuration Wizard and skip to page 19.
Section 3 - Configuration Click Next to continue. Create a new password and then click Next to continue. Select your time zone from the drop-down menu and then click Next to continue.
Section 3 - Configuration Select the type of Internet connection you use and then click Next to continue. If you selected Dynamic, you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click $MPOF :PVS 1$ T ."$ "EESFTT and then click Next to continue. The Host Name is optional but may be required by some ISPs. The default host name is the device name of the Router and may be changed.
Section 3 - Configuration If you selected PPPoE, enter your PPPoE username and password. Click Next to continue. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. If you selected PPTP, enter your PPTP username and password. Click Next to continue.
Section 3 - Configuration If you selected L2TP, enter your L2TP username and password. Click Next to continue. If you selected Static, enter your network settings supplied by your Internet provider. Click Next to continue. Click Connect to save your settings. Once the router is finished rebooting, click Continue. Please allow 1-2 minutes to connect.
Section 3 - Configuration Manual Configuration Dynamic (Cable) If you opt to set up your Internet connection manually, you will be redirected to a WAN page that allows you to select your Internet type and enter the correct configuration parameters. Select your Internet connection type using the “My Internet Connection is” drop-down menu. Click the Save Settings button when you have configured the connection.
Section 3 - Configuration Dynamic IP Address (DHCP) My Internet Select Dynamic IP (DHCP) to obtain IP Address Connection: information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for Cable modem services. Host Name: The Host Name is optional but may be required by some ISPs. Use Unicasting: Check the box if you are having problems obtaining an IP address from your ISP.
Section 3 - Configuration PPPoE (DSL) $IPPTF 111P& 1PJOU UP 1PJOU 1SPUPDPM PWFS &UIFSOFU JG ZPVS *41 VTFT B 111P& DPOOFDUJPO :PVS *41 XJMM QSPWJEF you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. My Internet Select PPPoE (Username/Password) from the drop-down Connection: menu.
Section 3 - Configuration PPTP $IPPTF 1151 1PJOU UP 1PJOU 5VOOFMJOH 1SPUPDPM JG ZPVS *41 VTFT B 1151 DPOOFDUJPO :PVS *41 XJMM QSPWJEF ZPV XJUI a username and password. This option is typically used for DSL services. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. PPTP IP Address: Enter the IP address (Static PPTP only).
Section 3 - Configuration MAC Address: The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended UIBU ZPV DIBOHF UIF EFGBVMU ."$ BEESFTT VOMFTT SFRVJSFE CZ ZPVS *41 :PV DBO VTF UIF $MPOF :PVS 1$ T ."$ "EESFTT button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
Section 3 - Configuration L2TP $IPPTF - 51 -BZFS 5VOOFMJOH 1SPUPDPM JG ZPVS *41 VTFT B - 51 DPOOFDUJPO :PVS *41 XJMM QSPWJEF ZPV XJUI B username and password. This option is typically used for DSL services. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. L2TP IP Address: Enter the L2TP IP address supplied by your ISP (Static only).
Section 3 - Configuration MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default MTU. Clone MAC The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not Address: SFDPNNFOEFE UIBU ZPV DIBOHF UIF EFGBVMU .
Section 3 - Configuration Russia PPTP $IPPTF 3VTTJB 1151 %VBM "DDFTT JG ZPVS *41 VTFT B 1151 DPOOFDUJPO :PVS *41 XJMM QSPWJEF ZPV XJUI B VTFSOBNF BOE QBTTXPSE This option is typically used for DSL services. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. PPTP IP Address: Enter the IP address (Static PPTP only). PPTP Subnet Enter the Primary and Secondary DNS server Mask: Addresses (Static PPTP only).
Section 3 - Configuration MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default MTU. Clone MAC The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended Address: UIBU ZPV DIBOHF UIF EFGBVMU ."$ BEESFTT VOMFTT SFRVJSFE CZ ZPVS *41 :PV DBO VTF UIF $MPOF :PVS 1$ T .
Section 3 - Configuration Russia PPPoE $IPPTF 3VTTJB 111P& %VBM "DDFTT JG ZPVS *41 VTFT B 111P& DPOOFDUJPO :PVS *41 XJMM QSPWJEF ZPV XJUI B VTFSOBNF BOE QBTTXPSE This option is typically used for DSL services. Internet Connection: Save your settings after configuring your Internet Connection method. Access Point Mode: Enable to turn your router into an access point. Internet Connection Choose your Internet Connection type.
Section 3 - Configuration Reconnect Select either Always-on, On-Demand, or Manual. Mode: Maximum Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Idle Time: Auto-reconnect. DNS Servers: Enter the Primary and Secondary DNS Server Addresses (Static L2TP only). MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default MTU.
Section 3 - Configuration Static IP Address 4FMFDU 4UBUJD *1 "EESFTT JG BMM UIF *OUFSOFU QPSU T *1 JOGPSNBUJPO JT QSPWJEFE UP ZPV CZ ZPVS *41 :PV XJMM OFFE UP FOUFS JO UIF *1 BEESFTT subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
Section 3 - Configuration Wireless Settings If you want to configure the wireless settings on your router using the wizard, click Wireless Connection Setup Wizard and refer to page 80. Click Add Wireless Device with WPS if you want to add a wireless device using Wi-Fi Protected Setup (WPS) and refer to page 83. If you want to manually configure the wireless settings on your router click Manual Wireless Network Setup and refer to the next page.
Section 3 - Configuration Manual Wireless Network Setup Enable Wireless: Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Click Add New to create your own time schedule to enable the wireless function. Wireless Network Service Set Identifier (SSID) is the name of your wireless Name: network. Create a name using up to 32 characters. The SSID is case-sensitive. 802.11 Mode: Select one of the following: 802.
Section 3 - Configuration Channel Width: Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices. 20MHz - Select if you are not using any 802.11n wireless clients. This is the default setting. Enable Hidden Select to enable hidden wireless. Wireless: Wireless Security: Refer to page 79 for more information regarding wireless security.
Section 3 - Configuration Network Settings This section will allow you to change the local network settings of the router and to configure the DHCP settings. IP Address: Enter the IP address of the router. The default IP address is 192.168.0.1. If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the configuration utility. Subnet Mask: Enter the Subnet Mask. The default subnet mask is 255.255.255.0.
Section 3 - Configuration DHCP Server Settings DHCP stands for Dynamic Host Control Protocol. The DIR-605 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-605.
Section 3 - Configuration NetBIOS Scope The users may add some characters behind the NetBIOS name to differentiate it from other D-Link routers. It follows the naming (optional): rule for DNS names. Primary/ Use this function to allow the seperate computers in a seperate subnet to search the computers in the same workgroup.
Section 3 - Configuration DHCP Reservation If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range. Computer Name: Enter the computer name or select from the drop-down menu and click <<. IP Address: Enter the IP address you want to assign to the computer or device.
Section 3 - Configuration Virtual Server The DIR-605 can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DIR-605 firewall feature filters out unrecognized packets to protect your LAN network so all computers networked with the DIR-605 are invisible to the outside world.
Section 3 - Configuration This will allow you to open a single port. If you would like to open a range of ports, refer to the next page. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Configuration Port Forwarding This will allow you to open a single port or a range of ports. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Configuration Application Rules Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-605.
Section 3 - Configuration QoS Engine The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classified automatically. Enable QoS Engine: This option is disabled by default. Enable this option for better performance and experience with online games and other interactive applications, such as VoIP.
Section 3 - Configuration Network Filters Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses GSPN BDDFTTJOH UIF /FUXPSL :PV DBO FJUIFS NBOVBMMZ BEE B ."$ BEESFTT PS TFMFDU UIF ."$ BEESFTT GSPN UIF MJTU PG clients that are currently connected to the Broadband Router. Configure MAC Select Turn MAC Filtering Off, allow MAC Filtering: addresses listed below, or deny MAC addresses listed below from the drop-down menu.
Section 3 - Configuration Access Control The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to only grant access to approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games. Add Policy: Check the Enable Access Control check box and click the Add Policy button to start the Access Control Wizard. Access Control Wizard Click Next to continue with the wizard.
Section 3 - Configuration Access Control Wizard (continued) Enter a name for the policy and then click Next to continue. Select a schedule (I.E. Always) from the drop-down menu and then click Next to continue. Enter the following information and then click Next to continue. t "EESFTT 5ZQF 4FMFDU *1 BEESFTT ."$ BEESFTT PS Other Machines. t *1 "EESFTT &OUFS UIF *1 BEESFTT PG UIF DPNQVUFS you want to apply the rule to.
Section 3 - Configuration Access Control Wizard (continued) Select the filtering method and then click Next to continue. Enter the rule: Enable - Check to enable the rule. Name - Enter a name for your rule. Dest IP Start - Enter the starting IP address. Dest IP End - Enter the ending IP address. Protocol - Select the protocol. Dest Port Start - Enter the starting port number. Dest Port End - Enter the ending port number. To enable web logging, click Enable. Click Save to save the access control rule.
Section 3 - Configuration Website Filters Website Filters are used to allow you to set up a list of allowed Web sites that can be used by multiple users through the network. To use this feature select to Allow or Deny, enter the domain or website and click Add, and then click Save Settings :PV NVTU BMTP TFMFDU Apply Web Filter under the Access Control section (page 40). Configure Website Select Deny or Allow computers access to Filter Below: only these sites.
Section 3 - Configuration Inbound Filters The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can configure inbound data filtering rules that control data based on an IP address range. Inbound Filters can be used with Virtual Server, Port Forwarding, or Remote Administration features. Name: Enter a name for the inbound filter rule. Action: Select Allow or Deny. Enable: Check to enable rule. Source IP Start: Enter the starting IP address.
Section 3 - Configuration Firewall Settings A firewall protects your network from the outside world. The D-Link DIR-605 offers a firewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
Section 3 - Configuration Advanced Network Settings (Routing) UPnP Settings: To use the Universal Plug and Play (UPnP™) feature, click on Enabled. UPNP provides compatibility with networking equipment, software and peripherals. WAN Ping: Unchecking the box will not allow the device to respond to pings. Blocking the ping may provide some extra security from hackers. Check the box to allow the Internet port to be “pinged”.
Section 3 - Configuration Advanced Wireless Settings Transmit Power: Set the transmit power of the antennas. Beacon Period: Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. RTS Threshold: This value should remain at its default setting of 2432. If inconsistent data flow is a problem, only a minor modification should be made.
Section 3 - Configuration Advanced Network Settings UPnP Settings: To use the Universal Plug and Play (UPnP ™ ) feature click on Enabled. UPNP provides compatibility with networking equipment, software and peripherals. WAN Ping: Unchecking the box will not allow the DIR-605 to respond to pings. Blocking the Ping may provide some extra security from hackers. Check the box to allow the Internet port to be “pinged”.
Section 3 - Configuration My IPv6 Connection: Select PPPoE from the drop-down menu. PPPoE: Enter the PPPoE account settings supplied by your Internet provider (ISP). Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Address Mode: Dynamic. Enter the IP address (Static PPPoE only). IP Address: Enter your PPPoE user name. User Name: Enter your PPPoE password and then retype the password in the next box.
Section 3 - Configuration Administrator Settings 5IJT QBHF XJMM BMMPX ZPV UP DIBOHF UIF "ENJOJTUSBUPS BOE 6TFS QBTTXPSET :PV DBO BMTP FOBCMF 3FNPUF .BOBHFNFOU There are two accounts that can access the management interface through the web browser. The accounts are admin and user. Admin has read/write access while user has read-only access. User can only view the settings but cannot make any changes. Only the admin account has the ability to change both admin and user account passwords.
Section 3 - Configuration Time Settings The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to automatically adjust the time when needed. Time Zone: Select the Time Zone from the drop-down menu.
Section 3 - Configuration SysLog 5IF #SPBECBOE 3PVUFS LFFQT B SVOOJOH MPH PG FWFOUT BOE BDUJWJUJFT PDDVSSJOH PO UIF 3PVUFS :PV NBZ TFOE UIFTF MPHT to a SysLog server on your network. Save Log Files to Click on the Save button to save log file to local Local Hard Drive: hard drive which can later send to the network administrator for troubleshooting. Enable Logging to Check this box to send the router logs to a SysLog SysLog Server: Server.
Section 3 - Configuration E-mail Settings The Email feature can be used to send the system log files, router alert messages, and firmware update notification to your e-mail address. Enable Email When this option is enabled, router activity logs are Notification: e-mailed to a designated e-mail address. From Email This e-mail address will appear as the sender Address: when you receive a log file or firmware upgrade notification via e-mail.
Section 3 - Configuration System Settings Save Settings to Use this option to save the current router Local Hard Drive: configuration settings to a file on the hard disk of the computer you are using. First, click the Save CVUUPO :PV XJMM UIFO TFF B GJMF EJBMPH where you can select a location and file name for the settings. Load Settings Use this option to load previously saved from Local Hard router configuration settings.
Section 3 - Configuration Update Firmware :PV DBO VQHSBEF UIF öSNXBSF PG UIF 3PVUFS IFSF .BLF TVSF UIF öSNXBSF ZPV XBOU UP VTF JT PO UIF MPDBM IBSE ESJWF PG the computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support TJUF GPS öSNXBSF VQEBUFT BU IUUQ TVQQPSU EMJOL DPN :PV DBO EPXOMPBE öSNXBSF VQHSBEFT UP ZPVS IBSE ESJWF GSPN UIF D-Link support site. Firmware Displays the current firmware version and date.
Section 3 - Configuration DDNS The DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.
Section 3 - Configuration System Check The System Check feature allows you to verify the physical connectivity on both LAN and Internet interface. Ping Test: The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP Address that you wish to Ping, and click Ping. Ping Results: The results of your ping attempts will be displayed here. System Check: The System Check tool can be used to verify the physical connectivity on both the LAN and Internet interfaces.
Section 3 - Configuration Schedules Name: Enter a name for your new schedule. Days: Select a day, a range of days, or All Week to include every day. Time: Check All Day - 24hrs or enter a start and end time for your schedule. Save: Click Save UP TBWF ZPVS TDIFEVMF :PV must click Save Settings at the top for your schedules to go into effect. Schedule Rules The list of schedules will be listed here. Click List: the Edit icon to make changes or click the Delete icon to remove the schedule.
Section 3 - Configuration Device Information This page displays the current information for the DIR-605. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed.
Section 3 - Configuration General: Displays the router’s time and firmware version. Internet: Displays the MAC address and the public IP settings for the router. LAN: Displays the MAC address and the private (local) IP settings for the router. Wireless LAN: Displays the wireless MAC address and your wireless settings such as SSID and Channel. LAN Computers: Displays computers and devices that are connected to the router via Ethernet and that are receiving an IP address assigned by the router (DHCP).
Section 3 - Configuration Log The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained.
Section 3 - Configuration Stats The screen below displays the Traffic Statistics. Here you can view the amount of packets that pass through the DIR-605 on both the Internet and the LAN ports. The traffic counter will reset if the device is rebooted.
Section 3 - Configuration Internet Sessions The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WANside computer. IP Address: The IP address and, where appropriate, port number of the local application. TCP Session: This shows the number of TCP packets being sent from the source IP address.
Section 3 - Configuration Wireless The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients.
Section 3 - Configuration Routing Table The routing table displays all routing related information configured for your router.
Section 3 - Configuration Support D-Link DIR-605 User Manual 70
Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DIR-605 offers the following types of security: t 81" 8J 'J 1SPUFDUFE "DDFTT t 81" 8J 'J 1SPUFDUFE "DDFTT t 81" 14, 1SF 4IBSFE ,FZ t 81" 14, 1SF 4IBSFE ,FZ What is WPA? WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
Section 4 - Security Wireless Connection Setup Wizard To run the security wizard, browse to the Setup page and then click the Wireless Connection Setup Wizard button. Click Next to continue.
Section 4 - Security Enter the SSID (Service Set Identifier). The SSID is the name of your wireless network. Create a name using up to 32 characters. The SSID is case-sensitive. Select the level of security for your wireless network: t #FTU 81" "VUIFOUJDBUJPO t #FUUFS 81" "VUIFOUJDBUJPO t /POF /P TFDVSJUZ Click Next to continue. If you selected Best or Better, enter a password between 8-63 characters. If you selected Good, enter 13 characters or 26 Hex digits. Click Next to continue.
Section 4 - Security If you selected Better, the following screen will show you your Pre-Shared Key to enter on your wireless clients. Click Save to finish the Security Wizard. If you selected Best, the following screen will show you your PreShared Key to enter on your wireless clients. Click Save to finish the Security Wizard. If you selected WPA-Enterprise, the RADIUS information will be displayed. Click Save to finish the Security Wizard.
Section 4 - Security Add Wireless Device with WPS Wizard From the Setup > Wireless Settings screen, click Add Wireless Device with WPS. Select Auto to add a wireless client using WPS (Wi-Fi Protected Setup). Once you select Auto and click Connect, you will have a 120 second time limit to apply the settings to your wireless client(s) and successfully establish a connection. If you select Manual, a settings summary screen will appear. Write down the security key and enter this on your wireless clients.
Section 4 - Security Configure WPA-Personal (PSK) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish XJSFMFTT DPOOFDUJWJUZ CFGPSF FOBCMJOH FODSZQUJPO :PVS XJSFMFTT TJHOBM NBZ EFHSBEF XIFO FOBCMJOH FODSZQUJPO EVF UP the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Setup and then click Wireless Settings on the left side. 2.
Section 4 - Security Configure WPA-Enterprise (RADIUS) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish XJSFMFTT DPOOFDUJWJUZ CFGPSF FOBCMJOH FODSZQUJPO :PVS XJSFMFTT TJHOBM NBZ EFHSBEF XIFO FOBCMJOH FODSZQUJPO EVF UP the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Setup and then click Wireless Settings on the left side.
Section 4 - Security D-Link DIR-605 User Manual 78
Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows Vista® Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista® utility as seen below.
Section 5 - Connecting to a Wireless Network Configure WPA/WPA2 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network. 2.
Section 5 - Connecting to a Wireless Network 3. Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 5 - Connecting to a Wireless Network Connect Using WCN 2.0 The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista ®. The following instructions for setting this up depends on whether you are using Windows Vista® to configure the router or third party software. When you first set up the router, Wi-Fi protection is disabled and unconfigured. To enjoy the benefits of Wi-Fi protection, the router must be both enabled and configured.
Section 5 - Connecting to a Wireless Network Using Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Section 5 - Connecting to a Wireless Network Configure WPA-PSK It is recommended to enable WEP on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WEP key being used. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router.
Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DIR-605. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screen shots on your computer will look similar to the following examples.) 1. Why can’t I access the web-based configuration utility? When entering the IP address of the D-Link router (192.168.0.
Section 6 - Troubleshooting t $POöHVSF ZPVS *OUFSOFU TFUUJOHT t (P UP Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. t $MJDL UIF Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. t (P UP UIF Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Section 6 - Troubleshooting 3. Why can’t I connect to certain sites or send and receive e-mails when connecting through my router? If you are having a problem sending or receiving e-mail, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to.
Section 6 - Troubleshooting :PV TIPVME TUBSU BU BOE XPSL ZPVS XBZ EPXO CZ FBDI UJNF 0ODF ZPV HFU B SFQMZ HP VQ CZ VOUJM ZPV HFU B fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480).
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks.
Appendix A - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford.
Appendix A - Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Appendix A - Wireless Basics Security Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up. Wireless Modes There are basically two modes of networking: t Infrastructure – All wireless clients will connect to an access point or wireless router.
Appendix B - Networking Basics Networking Basics Check your IP address After you install your adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows Vista ® users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows Vista® Windows® XP Windows® 2000 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. Click on Start > Control Panel > Network Connections. From the desktop, right-click My Network Places > Properties.
Appendix D - Contacting Technical Support Copyright ©2008 by D-Link Corporation/D-Link Systems, Inc. All rights reserved. CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
注意 ! 依據 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得 擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現 象時,應立即停用,並改善至無干擾時方得繼續使用。 前項合法通信,指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信或工 業、科學及醫療用電波輻射性電機設備之干擾。 IC EMI(ICES-003) "This Class B digital apparatus complies with Canadian ICES-003." "Cet appareil numérique de la classe Class B est conforme à la norme NMB-003 du Canada.