DPH-10U VoIP USB Phone Quick User Guide Version 1.
TABLE OF CONTENTS 1. INTRODUCTION ........................................................................................3 2. PACKAGE CONTENTS .............................................................................3 3. REQUIREMENTS.......................................................................................4 4. DPH-10U INSTALLATION .........................................................................4 5. ENABLING DPH-10U ..................................................................
1. Introduction This is a sleek powerful tool and easy to carry USB phone. It has USB port to connect into PC, and it allows you communicate with others through internet. It includes other features to enhance internet voice chat futures, because it has same ability as USB phone such as portable and easy to use, and you can use it for PC to PC or PC to Phone; along with crystal clear voice communication with minimize noise. It has phone’s look but it is best to use for family, office or SOHO 2.
3. Requirements In order to install the DPH-10U VoIP USB Phone you will need the following: 1. DPH-10U VoIP USB Phone 2. PC with the following minimum specifications: o Pentium 400MHz or equivalent o Windows 2000 or XP o Available USB port (1.0, 1.1 or 2.0) o Skype™ version 1.1.079 or higher (www.skype.com) must be installed o 128MB RAM o 10MB available hard disk space o CD-ROM drive to install DPH-10U software from the supplied CD-ROM 4.
STEP 3: Insert the supplied CD-ROM into your PC CD-ROM drive. The installation should start automatically. Please press “Software(Utility)”. STEP 4: You will see the following popup. Press Next to proceed or cancel to stop the install processes. STEP 5: You press the Install and stare to install the DPH-10U Utility.
STEP 6: You will see the following progress bar below indicating that the installation is proceeding. STEP 7: The program installing audio driver. Press Next. STEP 8: You will see the driver install path.
STEP 9: You will see the following progress bar below indicating that the installation is proceeding STEP 9: You will see the following progress bar below indicating that the installation is proceeding STEP 10: You will see the following popup. Press Finish to close the installation STEP 11: You will see the following popup.
STEP 12: When you will see the following screen, select the option, “allow this program to use Skype” and press the OK button. STEP 13: When the installation completes you should see the following message appear near your system tray and a new telephone icon (circled in red below) in your system tray as shown below.
You will see a new program group named “USB Phone”, accessed from the Start button -> All Programs as shown below. You final configuration should resemble the following.
5. Enabling DPH-10U In order to use DPH-10U and it’s features, (1) the DPH-10U VoIP USB Phone must be plugged into the PC, (2) the DPH-10U utility must be running (see green telephone in the Windows System Tray). If the DPH-10U utility is not running (i.e.
You should now see the DPH-10U in the Windows System Tray as shown below. You are now ready to use the DPH-10U VoIP USB Phone. 6.
7. DPH-10U States Icon Define Description Skype Mode (ON-Line) Detecting (OFF-Line) Mapping Mode Record This Mode is for Skype，All the Function keys are default。 This mode shows the system can not find USB Phone or utility not enable。 This mode is for VoIP, User is able to set 6 function keys 。 This mode shows the system is recording. 7.1 DPH-10U LEDs Showing LED light ON Flash Changing Color Description Normal mode On the Phone MIC Mute 7.
When Echo123 is added, click on the chat button as shown below. You will see the following chat screen and you should enter “callme” and press the Enter key on your keyboard. Within 10-20 seconds, you should see the following screen, and the DPH-10U VoIP USB Phone should ring. Pick up the handset and follow the instructions. The Echo Test Service will ask you to leave a message which will be played back immediately.
When the test concludes you can press OK on the following screen. and then press Finish on the following screen.
8. Utility Configuration Please right click on the DPH-10U in the system tray and select “Open” as shown below. 8.1 Overview You can see the software version and firmware version in this page S/W Ver. : 1.00 F/W Ver. : 1.00 8.2 System You can select “Mapping mode” or “Skype Mode” to support your softphone.
8.3 Mapping Mode If You select “Mapping Mode”. You can define 6 keys to control softphone After define key. You can save the key value in your computer. The default path C:\Program Files\USB Phone\USBPhone.ini. This files name can be change. 8.4 Skype Mode If You select “Skype Mode”. You can use default value for the keypad 8.
9. Recode Please press ● button and start to recording The system will show the icon. If you need stop recording, press ● button. The system will popup the Windows. Give a name to Files name.
10. Disabling DPH-10U In order to disable DPH-10U, right click on the DPH-10U in the system tray and select Close as shown below. You can now disconnect the DPH-10U from the PC. 11. Uninstall In order to uninstall the DPH-10U, click on the uninstall utility in the DPH-10U program group accessed from the Start button -> Programs -> USB Phone -> Uninstall USB Phone.
You will see the uninstall indicator as follows. When the uninstall indicator disappears, the un-installation is complete.
Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link Technical Support through our website, or by phone. Tech Support for customers within the United States: D-Link Technical Support over the Telephone: (877) 453-5465 24 hours a day, seven days a week.
