Wireless Print Server Wireless G Mobile USB 2.
System Requirements • 10/100 Fast Ethernet Wired or 802.11b/g Wireless Network • Printer with USB Port* • Computer with: • Windows® XP (SP2) or Windows® 2000 (SP4) • Internet Explorer 6.0 or Mozilla Firefox 1.5 or higher • CD-ROM Drive • Network Interface Card * For a list of compatible printers, visit http://support.dlink.com.
Hardware Overview Connections USB Ports Connect USB printers using an USB cable. Reset Button Pressing the Reset Button restores the router to its original factory default settings. Power Receptor Receptor for the Power Adapter. LAN Port Connect to a network using an Ethernet cable.
Hardware Overview LEDs LAN LED A solid light indicates connection on the LAN port. This LED blinks during data transmission. Power LED A solid light indicates a proper connection to the power supply. USB LEDs (1-4) A solid light indicates connectivity to an USB printer or scanner. WLAN LED A solid light indicates that the wireless segment is ready. This LED blinks during wireless data transmission.
Installation Connect an Ethernet cable to the Ethernet connector located on the Print Server’s back panel and attach it to the network. Note: It is required that an Ethernet cable is used during initial setup. Once your wireless configuration is set, you may disconnect the Ethernet cable and begin communicating wirelessly with your DPR-1260. Attach the external power supply to the DC power input connector located on the Print Server’s bottom panel and connect it to a power outlet or power strip.
Open a web browser and enter the following: http://dlink-XXXXXX XXXXXX = the last six characters of your MAC address. Wireless Settings If you want to connect to a wireless network, click on the Setup tab and then click Wireless Settings on the left side. You will be asked to enter a password. Leave the box empty if you have not set up a password. Set the Wireless on/off to On. If you want to disable the wireless feature, select Off. Select the Wireless Network Name (SSID) from the drop-down menu.
WEP Encryption It is recommended to enable encryption on your wireless router before your wireless print server. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration (refer to page 5). Click on Setup and then Wireless Settings on the left side. 2. Next to Security Mode, select WEP. 3. Next to Authentication, select Shared Key. 4.
WPA Encryption It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration (refer to page 5). 2. Next to Security Mode, select WPA. 3. Next to Cipher Mode, select TKIP, AES, or TKIP and AES. 4. Next to PSK, enter a key (passphrase).
D-Link Setup Wizard Once you have successfully configured the wireless settings, you are now ready to setup your network printer. You can disconnect the Ethernet cable and configure the printer from a wireless connection. Note: You will need to run this wizard from each computer that wishes to use the printer. To access the configuration utility, double-click on the My Network Places icon on your desktop and then double-click on “DPR-1260: dlink-xxxxxx”.
Click the radio button next to the printer you want to configure. Click Next to continue. Click Next to continue. You may need to insert your printer driver CD to load the drivers to your computer. If the autor un screen appears when inserting your printer driver CD, click cancel or close. Click Finish to complete the setup wizard.
Scan If you have a compatible multi-function printer with a scanner, you may scan using the print server’s web-based utility. 1. Select Scanner Bed (most common) or Automatic Document Feeder (ADF). If you select ADF, select the document size from the drop-down menu. 2. Select the size, resolution, color copy, and file format. 3. Click the Scan button to scan the document. For more information regarding your scanner, please refer to the scanner’s documentation.
Technical Support D-Link’s website contains the latest user documentation and software updates for D-Link products. U.S. and Canadian customers can contact D-Link Technical Support through our website or by phone. United States Telephone (877) 453-5465 Twenty four hours a day, seven days a week. World Wide Web http://support.dlink.com Canada Telephone (800) 361-5265 Monday through Friday, 7:30am to 9:00pm EST. World Wide Web http://support.dlink.ca Version 1.
