DSL-200 ADSL USB Modem User’s Guide Second Edition (November 2001) 6DSL200H..
DSL-200 ADSL USB Modem User’s Guide Wichtige Sicherheitshinweise 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den spätern Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. 5.
DSL-200 ADSL USB Modem User’s Guide Limited Warranty Hardware: D-Link warrants its hardware products to be free from defects in workmanship and materials, under normal use and service, for the following periods measured from date of purchase from D-Link or its Authorized Reseller: Product Type Warranty Period Complete products One year Spare parts and spare kits 90 days The one-year period of warranty on complete products applies on condition that the product's Registration Card is filled out and returned
DSL-200 ADSL USB Modem User’s Guide update or replacement which may be provided for download via the Internet, or to any update which may otherwise be provided free of charge. D-Link's sole obligation under this software warranty shall be to replace any defective software product with product which substantially conforms to D-Link's applicable product documentation. Purchaser assumes responsibility for the selection of appropriate application and system/platform software and associated reference materials.
DSL-200 ADSL USB Modem User’s Guide Trademarks Copyright 2000 D-Link Corporation. Contents subject to change without prior notice. D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective proprietors. Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems Inc.
Table of Contents ABOUT THIS USER’S GUIDE........................................................................................................ VI OVERVIEW OF THE USER’S GUIDE ........................................................................................................VI BEFORE YOU START................................................................................................................. VII OPERATING SYSTEMS ...........................................................................
DSL-200 ADSL USB Modem User’s Guide A BOUT T HIS U SER’S G UIDE This user’s guide tells you how to install your DSL-200 ADSL USB Modem and use it to connect to the Internet. ADSL services are provided by, and sold by a variety of businesses. Your ADSL service provider may be your telephone company, an Internet service provider (ISP), a business that specializes in providing network services or a combination of any of these.
DSL-200 ADSL USB Modem User’s Guide B EFORE Y OU S TART In addition to the Modem hardware and software drivers, you will to gather information before you begin to install the device. Your DSL service provider will give you information required for a successful ADSL connection. You will use this information when you decide which driver to install and when you configure the Modem.
DSL-200 ADSL USB Modem User’s Guide Microfilters Unless you are instructed to use a “line splitter” (see below), it will be necessary to install a microfilter (low pass filter) device for each telephone or telephone device (answering machines, Faxes etc.) that share the line with the ADSL service. Microfilters are easy-to-install, in-line devices, which attach to the telephone cable between the telephone and wall jack. Microfilters that install behind the wall plate are also available.
DSL-200 ADSL USB Modem User’s Guide ADSL Service In order to use the Modem you must first have ADSL service established with a DSL service provider. There are four standards used for ADSL connections known as ANSI T1.413 issue 2, G.Lite, G.dmt and G.hs. The standards differ somewhat as to data transfer speed or bit rate. For user convenience, the Modem supports the G.hs Auto-handshake ADSL standard. This allows the Modem to operate with either type of connection.
DSL-200 ADSL USB Modem User’s Guide Use the tables provided here to record the information you need to install the Modem. SETTINGS TABLE (all users) VPI: VCI: Software Driver: The driver used depends on the connection protocol used for your network services. Ø Select the WAN driver if your connection is a PPP connection. That is if you are using RFC 2364 PPP over ATM or RFC 2516 PPPoE PPP over Ethernet. Ø Select the LAN driver if you are using RFC 1483 Ethernet over ATM.
DSL-200 ADSL USB Modem User’s Guide Unpacking Open the shipping carton and carefully remove all items. In addition to this User's Guide, ascertain that you have: 1. D-Link DSL-200 USB Modem 2. USB cable 3. ADSL cable or connector 4.
DSL-200 ADSL USB Modem User’s Guide 1 2 INTRODUCTION ADSL modem technology is a relatively new technology and may be unfamiliar to the reader. In this section, we introduce you to ADSL technology and give a brief description of its key attributes. We also give a general description of the D-Link DSL-200 USB Modem and its main features.
DSL-200 ADSL USB Modem User’s Guide Product Features The D-Link DSL-200 Modem provides the following features: Ø G.hs compliant (Auto-handshake) Ø G.dmt full rate compliant Ø G.lite compliant Ø RFC 1483 (Bridged Ethernet) compliant Ø RFC 2364 PPP over ATM compliant Ø RFC 2516 PPP over Ethernet compliant Ø Compatible with all T1.413 issue 2 (full rate DMT over analog POTS), and CO DSLAM equipment Ø Compliant with USB Specification Revision 1.
DSL-200 ADSL USB Modem User’s Guide Front Panel LED Indicators There are two LED indicators on the Modem: ♦ Power - Indicates the Modem is powered on when lit. ♦ ADSL Link – Indicates a valid ADSL link has been established when lit.
DSL-200 ADSL USB Modem User’s Guide 2 3 MODEM INSTALLATION Before you connect the USB cable, you must install the driver. See the next chapter for driver installation instructions. The only cable you should connect initially is the ADSL cable. Place the Modem in a location so that you are able to view the LEDs. It should be placed in an area that is clean, dry and ventilated. Make certain it is not placed near a heat source.
DSL-200 ADSL USB Modem User’s Guide 3 4 S OFTWARE INSTALLATION The DSL-200 can be used with the following operating systems: ♦ Microsoft Windows 98 ♦ Microsoft Windows 98 Second Edition ♦ Microsoft Windows 2000 ♦ Microsoft Windows Millennium Edition The procedures for each system are slightly different so be sure to follow the instructions provided for your PC’s operating system. The Microsoft Plug and Play feature will automatically detect the modem after it has been installed.
DSL-200 ADSL USB Modem User’s Guide Install the Software Driver Install the software driver on a computer using the Windows 98, Windows 98 Second Edition, Windows 2000 or Windows Millennium Edition (Windows Me) operating system. There are two different drivers, the LAN (Local Area Network) or WAN (Wide Area Network) driver. The instructions in this chapter can be used for either the LAN or WAN driver, the installation procedure is identical for both.
DSL-200 ADSL USB Modem User’s Guide 4. In the Select ISP window, select ‘Other Service Provider’, and then click Next. 5. In the Select Driver Type window, choose the driver that best suits your ADSL connection, and then click Next. By default the WAN driver will be selected.
DSL-200 ADSL USB Modem User’s Guide 6. In the Communication Settings window you must provide the PVC settings, Encapsulation method and Modulation method for configuring the Modem. Type in the VPI and VCI values in their respective fields. Note: At this point you must choose the Encapsulation method and Modulation technique used for your ADSL connection. Be sure to have the correct information available. Refer to the Settings Table (page 5) if you have it completed. 7.
DSL-200 ADSL USB Modem User’s Guide 8. Again in the same window, select the proper Modulation settings using the drop-down menu. Your service provider will give you the appropriate Modulation settings. Choose either T1.413, Multimode, G.Lite or G.DMT. If your service provider has not specified a modulation setting, use Multimode. Click Next to continue. 9. The Start Copying Files window appears. Click Next to copy the needed driver files.
DSL-200 ADSL USB Modem User’s Guide 10. In the Setup Complete window, click Finish. 11. The DSL Installer window asks you to plug in the Modem. Plug the rectangular end of the USB cable into the USB port of your PC, and then plug the square end of the USB cable into the USB port of the ADSL Modem. The USB Modem will be detected and messages will be displayed as the modem software is installed. Note: For Windows 2000 applications, the “Digital Signature Not Found” window will appear again.
DSL-200 ADSL USB Modem User’s Guide Verify the ADSL Connection Before you continue to the final step, make sure that the ADSL connection has been established. This can be done easily using the Modem’s ADSL connection monitoring feature described below. Desktop Monitoring A new icon will appear in the System Tray of your desktop. These colored arrows will help you monitor the status of your ADSL connection. The table below summarizes how to interpret the icon indicator.
DSL-200 ADSL USB Modem User’s Guide 4 C ONNECT TO THE INTERNET Now that the driver has been installed, you are ready to connect to the Internet. You establish an Internet connection indirectly, using DSL link to your network service provider. Follow the instructions for the driver you have installed and the operating system you use on your computer. If you have installed the WAN driver, you are using PPP to connect to your network service provider.
DSL-200 ADSL USB Modem User’s Guide 2. In the Connect To window type in the correct User name and Password given to you by your ADSL or network service provider. Check the Save password box if do not want to retype the password if you need to reconnect. The Phone number field will display the VPI/VCI values you entered earlier. DO NOT change the numbers in the Phone number field. Click Connect. It may take a few seconds for the connection to be established. 3.
DSL-200 ADSL USB Modem User’s Guide Connect to Internet - LAN Driver Users If your ADSL connection uses either the RFC 1483 or the RFC 1577 protocol, you must set your own TCP/IP configuration. The following information will be provided to you by your DSL service provider: ü IP Address ü Subnet Mask ü Gateway ü DNS Host Name ü DNS Domain ü DNS Server Windows 98 or Windows Me (LAN Driver) Follow these steps if you are using the RFC 1483 or RFC 1577 protocol on a computer running Windows 98 or Windows Me.
DSL-200 ADSL USB Modem User’s Guide Windows 2000 (LAN Driver) 1. Double-click on the My Computer icon, then the Control Panel icon, and then the Network and Dial-up Connections icon. 2. The Network and Dial-up Connections window appears. Right click on the Local Area Connection for the D-Link DSL-200 USB ADSL Modem. 3. The Local Area Connection window appears. Click on Internet Protocol (TCP/IP), then click on Properties. 4. The Internet Protocol (TCP/IP) window appears.
DSL-200 ADSL USB Modem User’s Guide 5 5 MONITORING THE MODEM Once you have installed the Modem you can monitor the status of the ADSL connection by clicking on the connection icon in your System Tray or click on the DSL-200 icon in the Control Panel folder. Clicking on either icon will bring up the following window: The bright green circle under “Link Status” indicates a valid link. Identical bright green circles under Transmitting and Receiving indicate data activity on the ADSL line.
DSL-200 ADSL USB Modem User’s Guide Clicking on the Configuration tab will provide you with the configuration values currently employed by the Modem, including, the Modulation, the connection protocol, the Encapsulation method and the VPI/VCI pair used for the ADSL.
DSL-200 ADSL USB Modem User’s Guide 6 C HANGING MODEM C ONFIGURATION Once the Modem and software have been installed the communication settings may be easily updated by performing the following steps: 1. From your PC desktop click Start – Programs – D-Link DSL-200 ADSL Modem – Configure. A notification message will appear indicating that the setup process has begun.
DSL-200 ADSL USB Modem User’s Guide 2. The “Communication Settings” window will be displayed. Make the necessary changes to the VPI, VCI, Encapsulation type and/or Modulation type and click Apply. 3. The new settings will be applied after restarting the computer. If you want to restart now click Finish. If you do not want to restart now select the “No, I will restart my computer later.” option and then click Finish.
DSL-200 ADSL USB Modem User’s Guide A 6 T ECHNICAL S PECIFICATIONS General ANSI T1.413 issue 2 ITU G.992.1 (G.dmt) Standards: ITU G.992.2 (G.lite) ITU G.994.1 (G.hs) USB 1.1 specifications RFC 2364 PPP over ATM Adaptation Layer 5 Protocol: RFC 2516 PPP over Ethernet RFC 1483 Multiprotocol Encapsulation over ATM Adaptation Layer 5 G.dmt full rate downstream: up to 8Mbps Data Transfer Rate: G.dmt full rate upstream: up to 640Kbps G.lite ADSL downstream: up to 1.
DSL-200 ADSL USB Modem User’s Guide B 7 U NINSTALLING THE MODEM If you need to uninstall the Modem, use the Uninstall program available in the DSL-200 Modem folder. Failure to use the Uninstall program can leave files in the system that can cause problems with future installations, including problems with reinstallation of the Modem. IMPORTANT: Do not remove the Modem using the device manager. You must use the Uninstall Program to remove the device.
DSL-200 ADSL USB Modem User’s Guide 2. You are asked to confirm your intention to remove the device. Click Yes to uninstall the Modem. 3. A new window appears and asks that you not unplug the USB cable until after the device driver has been completely removed. Click OK to proceed. 4. The final window informs you that the uninstall process is now complete. You can restart now if you wish, however do not disconnect the USB cable until the computer has shut down.
Offices Australia D-Link Australasia Unit 16, 390 Eastern Valley Way, Roseville, NSW 2069 Australia TEL: 61-2-9417-7100 FAX: 61-2-9417-1077 TOLL FREE (Australia): 1800-177100 TOLL FREE (New Zealand): 0800-900900 URL: www.dlink.com.au E-MAIL: support@dlink.com.au & info@dlink.com.au Canada D-Link Canada 2180 Winston Park Drive, Oakville, Ontario, L6H 5W1 Canada TEL: 1-905-829-5033 FAX: 1-905-829-5095 BBS: 1-965-279-8732 TOLL FREE: 1-800-354-6522 URL: www.dlink.ca FTP: ftp.dlinknet.
Netherlands D-Link Benelux Fellenoord 1305611 ZB, Eindhoven, the Netherlands TEL: 31-40-2668713 FAX: 31-40-2668666 URL: www.d-link-benelux.nl Norway D-Link Norway Waldemar Thranesgt. 77, 0175 Oslo, Norway TEL: 47-22-991890 FAX: 47-22-207039 Russia D-Link Russia Michurinski Prospekt 49, 117607 Moscow, Russia TEL: 7-095-737-3389 & 7-095-737-3492 FAX: 7-095-737-3390 URL: www.dlink.ru E-MAIL: vl@dlink.
Registration Card Print, type or use block letters. Your name: Mr./Ms __________________________________________________________________________ Organization: ____________________________________________ Dept.
7. What applications are used on your network? oDesktop publishing oSpreadsheet oWord processing oCAD/CAM oDatabase management oAccounting oOthers_________________________________________________ 8.
