DVA-G3340S High-Speed 2.
Contents Package Contents .............................................................................4 Introduction ........................................................................................5 Features................................................................................................8 Using the Web Interface ................................................................
Advanced Advanced Advanced Advanced Advanced Advanced Advanced Advanced Advanced > > > > > > > > > DMZ ................................................................................................62 Firewall...........................................................................................63 RIP ..................................................................................................65 PPP .................................................................................................
Package Contents Contents of Package: D-Link DVA-G3340S High-Speed 2.4GHz Wireless ADSL VoIP Router Power Adapter - AC 12V, 1200mA Manual and Warranty on CD RJ-11 Cable Ethernet Cable USB Cable Note: Using a power supply with a different voltage rating than the one included with the DVA-G3340S will cause damage and void the warranty for this product. If any of the above items are missing, please contact your reseller.
Introduction The D-Link DVA-G3340S High-Speed Wireless Router is an 802.11g high-performance, wireless router that supports high-speed wireless networking at home, at work or in public places. Unlike most routers, the DVA-G3340S provides data transfers at up to 5X (compared to the standard 11 Mbps) when used with other D-Link AirPlus G products. The 802.11 g standard is backwards compatible with 802.11 b products. This means that you do not need to change your entire network to maintain connectivity.
Connections The 12V 1.2A AC power adapter plugs in here. This is where your Wireless LAN antenna connects. ADSL port provides a connection to your ISP and the WAN (Internet). Line port provides a connection to your regular telephone line from the wall outlet. The reset button returns the DVA-G3340S to its factory default settings. FXS1 and FXS2 ports provide connections to two analog (POTS) telephones.
LEDs LAN − These LEDs will be lit green when a LAN connection is detected. They will blink when there is data activity on the connection. WLAN − This LED will be lit green when a Wireless LAN connection is detected. It will blink when there is data activity on the connection. USB − This LED will light green when a USB connection is detected. It will blink when there is data activity on the connection.
Features Fully compatible with the 802.11g standard to provide a wireless data rate of up to 54Mbps Backwards compatible with the 802.
Using the Web Interface Whenever you want to configure your network or the DVA-G3340S, you can access the Configuration Menu by opening the web-browser and typing in the IP Address of the DVA-G3340S. The DVA-G3340S default IP Address is shown below: Open your web browser Type in the IP Address of the Router (http://10.1.1.1) Note: if you have changed the default IP Address assigned to the DVA-G3340S, make sure to enter the correct IP Address.
Wireless Settings Home > Wireless The two essential settings for wireless LAN operation are the SSID and Channel Number. The SSID (Service Set Identifier) is used to identify a group of wireless LAN components. The SSID can be broadcast or can be hidden (not broadcast). Use the Advanced Wireless Settings menu to configure these basic settings. Wireless security using encryption (WEP) or access limitation (WPA) is also configured with the Wireless Settings method.
4. 5. The Channel: may be changed to channels that are available in your region. Channels available for wireless LAN communication are subject to regional and national regulation. Click the Apply button to save any change to the Channel. Make sure you save the new wireless settings. Use the Tools > System menu to save the new settings. DVA-G3340S User Manual Page 11 of 94 V1.
Wireless Settings − WEP Home > Wireless > WEP The wireless LAN interface of the DVA-G3340S has various security features used to limit access to the device or to encrypt data and shared information. The available standardised security for wireless LAN includes WEP and WPA Wireless security is configured with the Wireless Settings menu located in the Home directory. Wireless Security − WEP Security Options for Wireless In the Wireless Settings menu, select the type of security you want to configure.
WEP can use open or shared keys, or may be configured to allow the clients to use either type of key. Use the Authentication Type: drop-down menu to choose Open, Shared or Both. • Select Open to allow any wireless station to associate with each other through the access point. Wireless devices will be able to communicate with all devices on a network unless they require a Shared key. • Select Shared to only allow stations using a shared key encryption to associate with each other through the access point.
Wireless Settings − WPA Home > Wireless > WPA WPA security for wireless communication has been developed to overcome some of the shortcomings of WEP. WPA uses an improved encryption method combined with an authentication procedure. Wireless Security − WPA Configure WPA Settings To configure WPA settings, select the WPA option. The menu will change to offer the appropriate settings. WPA can be configured to work with 802.1x network authentication, or to use a PSK Hex or PSK String key.
Wireless Settings − WPA-PSK Home > Wireless > WPA-PSK WPA-PSK requires a shared key but does not use a separate server for authentication. PSK keys can be ASCII or Hex type. Wireless Security − WPA-PSK Configuring WPA-PSK Security for WLAN To use WPA with a PSK key: 1. Select the PSK Hex (Hexadecimal key) or PSK String (ASCII key) option. 2. Type in the Hex: or String: key in the appropriate entry field. Click the Apply button to put the changes into effect.
Configuring the WAN Connection Home > WAN > PPPoE/PPPoA To configure the Router’s basic configuration settings without running the Setup Wizard, you can access the menus used to configure WAN, LAN, DHCP and DNS settings directly from the Home directory. To access the WAN Settings menu, click on the WAN link button on the left side of the first window that appears when you successfully access the web manager.
PPPoE and PPPoA Connection for WAN Follow the instructions below to configure the Router to use a PPPoE or PPPoA for the Internet connection. Make sure you have all the necessary information before you configure the WAN connection. 1. If not already selected, choose the PPPoE/PPPoA option from the WAN Settings pull-down menu. PPPoE/PPPoA is selected by default if you are configuring the Router for the first time. 2.
you will not be able to use the features configured in the Firewall and Filters menus located in the Advanced tab. See the next chapter for more details on these menus. 10. Typically the global IP settings (i.e. IP address for the WAN interface) for a PPPoA or PPPoA connection will use Dynamic IP assignment from the ISP. Some accounts may be assigned a specific global IP address.
MTU The Maximum Transmission Unit size may be changed if you want to optimize efficiency for uploading data through the WAN interface. The default setting (1400 bytes) should be suitable for most users. Some user may want to adjust the setting to optimize performance for wireless traffic or when low latency is desired (such as with Internet gaming). It is highly recommended that the user research how adjusting the MTU may affect network traffic for better or worse.
the global IP address provided to you by your ISP. The IP Unnumbered option is used if you want to set up a non-TCP/IP port protocol link through the WAN interface. An IP Unnumbered interface does not have an IP address and therefore cannot be managed via Telnet or any other TCP/IP application. Static IP DVA-G3340S User Manual If you have selected the Static IP option in the IP Control menu, type in the global IP address used for your WAN interface. This should be given to you by your ISP.
Dynamic IP Address Connection for WAN Home > WAN > Dynamic IP Address A Dynamic IP Address connection configures the Router to automatically obtain its global IP address from a DHCP server on the ISP’s network. The service provider assigns a global IP address from a pool of addresses available to the service provider. Typically the IP address assigned has a long lease time, so it will likely be the same address each time the Router requests an IP address.
adapter when you first access their network. This can prevent the Router (which has a different MAC address) from being allowed access to the ISPs network (and the Internet). To clone the MAC address of your computer’s Ethernet adapter, type in the MAC address in the Cloned MAC Address field and click the Clone MAC Address button. 5. Leave the MTU value at the default setting (default = 1400) unless you have specific reasons to change this (see table below). 6. NAT should remain enabled.
cloned MAC address with the factory default setting, type in all zeros - 0:0:0:0:0:0 - and click the Clone MAC Address button. MTU The Maximum Transmission Unit size may be changed if you want to optimize efficiency for uploading data through the WAN interface. The default setting (1400 bytes) should be suitable for most users. Some user may want to adjust the setting to optimize performance for wireless traffic or when low latency is desired (such as with Internet gaming).
Bridged Connection for WAN Home > WAN > Bridge Mode For Bridged connections it will be necessary for most users to install additional software on any computer that will the Router for Internet access. The additional software is used for the purpose of identifying and verifying your account, and then granting Internet access to the computer requesting the connection. The connection software requires the user to enter the User Name and Password for the ISP account.
method used for your ADSL service. The available options are 1483 Bridged IP LLC and 1483 Bridged IP VC-Mux. If have not been provided specific information for the Connection Type setting, leave the default setting. 4. Most users will not need to change ATM settings. If this is the first time you are setting up the ADSL connection it is recommended that you leave the Service Category settings at the default values until you have established the connection.
Static IP Address for Connection WAN Home > WAN > Static IP Address When the Router is configured to use Static IP Address assignment for the WAN connection, you must manually assign a global IP Address, Subnet Mask and Gateway IP Address used for the WAN connection. Most users will also need to configure DNS server IP settings in the DNS Settings configuration menu (see below). Follow the instruction below to configure the Router to use Static IP Address assignment for the WAN connection.
IP Address This is the permanent global IP address for your account. This is the address that is visible outside your private network. Get this from your ISP. Subnet Mask This is the Subnet mask for the WAN interface. Get this from your ISP. Gateway Address This is the IP address of your ISP’s Gateway router. It provides the connection to the Router for IP routed traffic that is outside your ISP’s network. That is, this will be the primary connection from the Router to most of the Internet.
Firewall DVA-G3340S User Manual Use this to universally enable or disable the Firewall and Filter features available in the Router. If you disable this you will not be able to configure settings in the Firewall or Filters menus in the Advanced directory. Page 28 of 94 V1.
ATM Traffic Shaping Home > WAN > ATM The ATM settings in the WAN configuration menus for the different connection types can be used to adjust QoS parameters for ADSL clients. This may not be available to all ADSL accounts. Ask your ISP if ATM Traffic Shaping is available for your account.
desirable to specify the PCR. CBR – Constant Bit Rate, usually used in circumstances where very low packet loss and very low Cell Delay Variable (CDV) are desirable. VBR – Variable Bit Rate, usually used when network traffic is characterized by bursts of packets at variable intervals, and some moderate packet loss and delay is acceptable. This category is typically used for audio and video applications such as teleconferencing. The network must support QoS Class 2 to use VBR.
ATM VC Settings Home > WAN > ATM VC Settings The ATM settings in the WAN configuration menus for the different connection types can be used to adjust QoS parameters for ADSL clients. This may not be available to all ADSL accounts. Ask your ISP if ATM Traffic Shaping is available for your account. ATM VC Settings in WAN connection menu The table below describes the ATM VC settings used to configure a connection for an ADSL account.
disabled. WAN Setting DVA-G3340S User Manual Use this to change the type of connection used. The options are: PPPoE/PPPoA, Dynamic IP Address, Static IP Address and Bridge Mode. Each option will offer different settings for configuration. Page 32 of 94 V1.
Multiple Virtual Connections Home > WAN > Multiple PVC Settings The Router supports multiple virtual connections. Up to eight PVCs to eight separate destinations can be created and operated simultaneously utilizing the same bandwidth. Additional PVC connections can be added for various purposes. For example, you may want to establish a private connection to remote office in order to create an extended LAN, or setup a server on a separate connection.
LAN IP Settings Home > LAN You can configure the LAN IP address to suit your preference. Many users will find it convenient to use the default settings together with DHCP service to manage the IP settings for their private network. The IP address of the Router is the base address used for DHCP. In order to use the Router for DHCP on your LAN, the IP address pool used for DHCP must be compatible with the IP address of the Router.
DHCP Settings Home > DHCP The DHCP server is enabled by default for the Router’s Ethernet LAN interface. DHCP service will supply IP settings to workstations configured to automatically obtain IP settings that are connected to the Router though an Ethernet port. When the Router is used for DHCP it becomes the default gateway for DHCP client connected to it. Keep in mind that if you change the IP address of the Router the range of IP addresses in the pool used for DHCP on the LAN will also be changed.
Router must be restarted for the settings to go into effect. To save the new settings and restart the Router, click on the Tools directory tab and then click the System menu button. Click the Save & Reboot button under Save Settings and Reboot the System. The Router will save the new DHCP settings and restart. Use the Router for DHCP To use the built-in DHCP server, click to select the DHCP Server option if it is not already selected. The IP Address Pool settings can be adjusted.
Disabling the DHCP Server To disable DHCP, click to select the No DHCP option and click on the Apply button. Choosing this option requires that workstations on the local network must be configured manually or use another DHCP server to obtain IP settings. If you configure IP settings manually, make sure to use IP addresses in the subnet of the Router. You will need to use the Router’s IP address as the Default Gateway for the workstation in order to provide Internet access.
DNS Settings Home > DNS The Router can be configured to relay DNS settings from your ISP or another available service to workstations on your LAN. When using DNS relay, the Router will accept DNS requests from hosts on the LAN and forward them to the ISP’s, or alternative DNS servers. DNS relay can use auto discovery or the DNS IP address can be manually entered by the user. Alternatively, you may also disable the DNS relay and configure hosts on your LAN to use DNS servers directly.
Dynamic DNS Settings Home > Dynamic DNS The Router supports DDNS, a service that maps Internet domain names to IP addresses. DDNS serves a similar purpose to DNS in that DDNS allows anyone hosting a Web or FTP server to advertise a public name to prospective users. Unlike DNS that only works with static IP addresses, DDNS works with dynamic IP addresses, such as those assigned by an ISP or other DHCP server.
VOIP Settings − Server Settings Home > Voice > Server The Router can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). Configure VOIP Server Settings The table below describes the VOIP Server settings. VOIP Server Parameters Description Server Address Enter the IP address of the SIP Server in this field. Server Port Enter the SIP server’s listening port for the SIP in this field.
VoIP service provider did not give you a server port number for SIP. Service Domain URL Scheme User Parameter Initial Unregister Register Expires Session Expires Min-SE Session Expires Refresher DVA-G3340S User Manual Enter the SIP service domain name in this field. Select SIP-URL to have the router include the domain name with the SIP number in the SIP messages that it sends. Select TEL-URL to have the router use the SIP number without a domain name in the SIP messages that it send.
VOIP Settings − User Agent Home > Voice > User Agent The Router can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). Configure VOIP User Agent Settings The table below describes the VOIP User Agent settings. VOIP User Agent Parameters Same Phone Number Line Phone Number DVA-G3340S User Manual Description Use this field to Enable or Disable the use of the same telephone number for the User Agent as for the Server Agent.
Display Name User Agent Port Authentication Username Authentication Password Confirm Password DVA-G3340S User Manual The name that will be displayed when the User Agent is in use. This selects the port number the router will listen to when determining when calls are being made. The Username used to access your SIP server and your VoIP service provider. The Password used to access your SIP server and your VoIP service provider. Retype your password to confirm. Page 43 of 94 V1.
VOIP Settings − Peer to Peer Home > Voice > Peer to Peer The Router can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). Configure VOIP Peer to Peer Settings The table below describes the VOIP Peer to Peer settings. VOIP Peer to Peer Parameters Index Phone Number User IP Address DVA-G3340S User Manual Description Index shows you what the current ID is for the rules you are creating in the table.
Port DVA-G3340S User Manual one in the first field. The second field is for the IP address of the Phone. This selects the port number the router will contact when this call is being made. Page 45 of 94 V1.
VOIP Settings − Telephony Home > Voice > Telephony The Router can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). Configure VOIP Telephony Settings DVA-G3340S User Manual Page 46 of 94 V1.
The table below describes the VOIP Telephony settings. VOIP Telephony Parameters Description Index EC VAD OOB DTMF Payload Type RX Gain TX Gain Inter-Digit Timer Codec Priority & Packet Interval DVA-G3340S User Manual Index allows you to select the current port you want to configure. This directly relates to the FXS1 or FXS2 ports on the back of the unit. Echo Cancellation (EC) – G.168 is an ITU standard for eliminating echo.
Caller ID DVA-G3340S User Manual Set a numerical Caller ID of up 32 digits. 5 caller IDs can be created and will be listed below the Distinctive Ringing area. To edit or delete an entry that has already been created, find the entry in the list and click on the appropriate icon. Page 48 of 94 V1.
VOIP Settings − ACR Home > Voice > ACR The Router can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). Configure VOIP ACR Settings The table below describes the VOIP Telephony settings. VOIP ACR Parameters Index Number Del Digit DVA-G3340S User Manual Description Index shows you what the current ID is for the rules you are creating in the table. Allows you to configure a number that is used as a prefix for dialing out to the PSTN.
Advanced Settings The Advanced tab has many pages of settings for you to view and configure: UPnP, Virtual Server, LAN Clients, SNMP, Filters, Bridge Filters, Routing, DMZ, Firewall, RIP, PPP, ADSL, ATM VCC, Wireless Management, and Wireless Performance. Universal Plug n Play Advanced > UPnP UPnP supports zero-configuration networking and automatic discovery for many types of networked devices.
Virtual Server Advanced > Virtual Server Use the Virtual Server menu to set up port forwarding rules in the Router. The Virtual Server function allows remote users to access services on your LAN such as FTP for file transfers or SMTP and POP3 for e-mail. The DVA-G3340S will accept remote requests for these services at your Global IP Address, using the specified TCP or UDP protocol and port number, and then redirect these requests to the server on your LAN with the Private IP address you specify.
services to an appropriate server on the users’ LAN. To choose a particular service click a radio button from the category list and highlight the service from the Available Rules list. Click Add, and then click Apply to save the rule. Ensure you Save & Reboot to make this rule effective. You may be prompted to add a LAN IP to the Client list, this will redirect you to the LAN Clients page, see below for more info. DVA-G3340S User Manual Page 52 of 94 V1.
SNMP Advanced > SNMP This menu can be accessed directly by clicking on the SNMP button or hyperlink in the Advanced setup menu. Simple Network Management Protocol (SNMP) is an OSI Layer 7 Application designed specifically for managing and monitoring network devices. SNMP enables network management stations to read and modify the settings of gateways, routers, switches, and other network devices.
TR-069 Advanced > TR069 This menu can be accessed directly by clicking on the TR069 button or hyperlink in the Advanced setup menu. This feature is currently only supported by certain Internet Service Providers and will not require any changes unless instructed. TR069 Configuration Menu DVA-G3340S User Manual Page 54 of 94 V1.
IP Filters Advanced > Filters Filter rules in the Router are put in place to allow or block specified traffic. The Filter Rules however can be used in a single direction to examine and then Allow or Deny traffic for Inbound (WAN to LAN) or Outbound (LAN to WAN) routed data. The rules based on IP address and TCP/UDP port. Configure the filter rules as desired and click the Apply button to create the rule. The newly created rule appears listed in the Outbound Filter List at the bottom of the menu.
The parameters described below are used to set up filter rules. Parameter Description Source IP For an Outbound Filter, this is the IP address or IP addresses on your LAN for which you are creating the filter rule. For an Inbound Filter, this is the IP address or IP addresses for which you are creating the filter rule. You can opt to indicate a Mask Range, a Single IP, an IP Range or Any IP from the pull-down menu.
Bridge Filters Advanced > Bridge Filters Bridge filters are used to block or allow various types of packets through the WAN interface. This may be done for security or to improve network efficiency. The rules are configured for individual devices based on MAC address. Filter rules can be set up for source, destination or both. You can set up filter rules and disable the entire set of rules without loosing the rules that have been configured.
button. The rule will appear in the entry field below as it is currently configured. To edit an existing rule, select the rule by clicking the corresponding Edit radio button. Make the desired changes and click the Add button. To remove a bridge filter from the table in the bottom half of the window, click to select the corresponding Delete box, and then click Apply. Remember to save the configuration changes. DVA-G3340S User Manual Page 58 of 94 V1.
LAN Clients Advanced > Lan Clients The LAN Clients menu is used when establishing Port Forwarding, Access Control and Advanced Security rules for IP addresses on the LAN. This menu can be accessed directly by clicking on the LAN Clients button or hyperlink in the Advanced setup menu. You can also click on the New IP button located in the Port Forwarding, Access Control and Advanced Security menus to access this menu.
Routing Advanced > Routing Use Static Routing to specify a route used for data traffic within your Ethernet LAN or to route data on the WAN. This is used to specify that all packets destined for a particular network or subnet use a predetermined gateway. Routing Menu To add a static route to a specific destination IP on the local network, enter a Destination IP address, Netmask, then click the Gateway radio button and type in the Gateway’s IP address.
radio button and choose a connection from the pull-down menu, then enter a Destination IP address and Netmask. Click Apply to enter the new static route in the table below. The route becomes active immediately upon creation To remove a static route from the table in the bottom half of the window, choose to Delete it from the table and click the Apply button. Remember to save the configuration changes. DVA-G3340S User Manual Page 61 of 94 V1.
DMZ Advanced > DMZ Since some applications are not compatible with NAT, the Router supports use of a DMZ IP address for a single host on the LAN. This IP address is not protected by NAT and will therefore be visible to agents on the Internet with the right type of software. Keep in mind that any client PC in the DMZ will be exposed to various types of security risks.
Firewall Advanced > Firewall The Firewall Configuration menu allows the Router to enforce specific predefined policies intended to protect against certain common types of attacks. There are two general types of protection (DoS, Port Scan) that can be enabled on the Router, as well as filtering for specific packet types sometimes used by hackers. You can choose to Enable or Disable protection against a customized basket of attack and scan types.
Null Scan attack IKE from WAN SYN/RST attack RIP from WAN SYN/FIN Scan DHCP from WAN A DoS "denial-of-service" attack is characterized by an explicit attempt by attackers to prevent legitimate users of a service from using that service.
Routing Information Protocol (RIP) Advanced > RIP The Router supports RIP v1 and RIP v2 used to share routing tables with other Layer 3 routing devices on your local network or remote LAN. Dynamic Routing (RIP) menu To enable RIP, select Enabled from the RIP pull-down menu, select the Protocol (RIPv1 and RIPv1 Compatible) and Direction (In, Out, or Both), and click Apply. The RIPv1 Compatible option will transmit RIPv2 broadcast packets and receive both RIP v1 and RIP v2 packets.
PPP Connection State Advanced > PPP When the WAN connection is configured for either PPPoA or PPPoE, you can configure the Router’s PPP session to remain on all the time, or to disconnect after some period of no activity. You may also choose to instruct the Router to connect each time you want to access the WAN or the Internet. PPP Connection settings menu If you want the Internet or WAN connection to be available any time a host on your LAN requests access, select the Always On option.
ADSL Advanced > ADSL The ADSL Configuration page allows the user to set the configuration for ADSL protocols. For most ADSL accounts the default settings Multi-mode will work. This configuration works with all ADSL implementations. If you have been given instructions to change the Modulation method used, select the desired option T1.413, G.dmt, or G.lite and click the Apply button. ADSL Modulation Configuration DVA-G3340S User Manual Page 67 of 94 V1.
ATM VC Setting Advanced > ATM VCC The ATM Virtual Circuit connection menu is used to configure the WAN connection. If you are using multiple PVCs, you can change the configuration of any PVC in this menu. To create new or additional PVCs, read the section below on Multiple PVCs. This menu can be used as an alternative menu to configure the same settings found on the WAN menu in the Home directory.
Quality of Service (QoS) Advanced > QoS QoS is an implementation of the IEEE 802.1p standard that allows network administrators a method of reserving bandwidth for important functions that require a large bandwidth or have a high priority, such as VoIP (Voice-over Internet Protocol), web browsing applications, file server applications or video conferencing. Not only can a larger bandwidth be created, but other less critical traffic can be limited, so excessive bandwidth can be saved.
Wireless Management Advanced > Wireless Management The Wireless Management menu located in the Advanced directory is used to control MAC address access to the wireless access point and to view a list of MAC addresses that are currently associated with the access point. This menu is also be used to enable and configure use of multiple SSIDs. To use more than one SSID, WEP and WPA security must first be disabled (see below).
1. 2. 3. 4. 5. Click in the Enable Access List option box to select it. Select the action to perform on the MAC address to be specified. Choose to Allow or Ban association. Type in the MAC Address in the entry field provided. Click the Add button to add the MAC address to the list. The AMC address will appear listed in the table below. After compiling the list of MAC addresses as desired, click the Apply button to enforce access control for the MAC addresses in the list.
Wireless Performance Advanced > Wireless Performance If you want to tweak wireless settings, click the Wireless Performance menu button in the Advanced directory Wireless LAN Performance settings DVA-G3340S User Manual Page 72 of 94 V1.
Tools The Tools tab allows you to set up basic maintenance features on the ADSL router. The windows available under this tab include Admin, Time, Remote Log, System, Firmware, Miscellaneous, and Test. Administrator Settings Tools > Admin Click the Tools tab to reveal the menu buttons for various functions located in this directory. The Administrator Settings is the first menu that appears in the Tools directory.
Change System Password To change the password used to access the Router web manager, click the Admin button in the Tools directory to display the Administrator Settings menu. Under the Administrator heading, type the New Password and Confirm Password to be certain you have typed it correctly. Click the Apply button to activate the new password. The System User Name remains “admin”, this cannot be changed using the web manager interface. Be sure to save the new setting.
Time (SNTP) Tools > Time The Router provides a number of options to maintain current date and time including SNTP. Time & Date Configuration To configure system time on the Router, select the method used to maintain time. The options available include SNTP, using your computer’s system clock (default) or set the time and date manually. If you opt to use SNTP, you must enter the SNTP server URL or IP address. Click the Apply button to set the system time. DVA-G3340S User Manual Page 75 of 94 V1.
Remote Log Tools > Remotelog The router provides the ability to send the data from the log to a remote server using a Syslog Service. This can be configured to be basic log data to more sophisticated debug information from the unit for troubleshooting. Remotelog Configuration You can even configure multiple logs for different Log Levels to different IP addresses. DVA-G3340S User Manual Page 76 of 94 V1.
System Settings Tools > System Save or Load Configuration File Once you have configured the Router to your satisfaction, it is a good idea to back up the configuration file to your computer. To save the current configuration settings to your computer, click the Admin button in the Tools directory to display the Administrator Settings menu. Click the Save button to Save Settings to Local Hard Drive. You will be prompted to select a location on your computer to put the file. The file type is .
Save Settings and Reboot the System Pressing the Save & Reboot button will save all current settings to the devices memory. The unit will then restart with all of these saved settings. Restore Factory Default Settings To reset the Router to its factory default settings, click the Restore button in the Administrator Settings menu. You will be prompted to confirm your decision to reset the Router. The Router will reboot with the factory default settings including IP settings and Administrator password.
Firmware Upgrade Tools > Firmware Use the Firmware Upgrade menu to load the latest firmware for the device. Note that the device configuration settings may return to the factory default settings, so make sure you save the configuration settings with the System Settings menu described above. Firmware Upgrade To upgrade firmware, type in the name and path of the file or click on the Browse button to search for the firmware file. Click the Apply button to begin copying the file.
Ping Test Tools > Miscellaneous To perform a standard Ping test for network connectivity, click the Misc. menu button in the Tools directory to view the Miscellaneous Configuration menu. Miscellaneous Configuration menu Ping Test The Ping test functions on the WAN and LAN interfaces. Type the IP address you want to check in the space provided and click the Ping button. Read the Ping test result in the space immediately below.
use IGMP to perform remote configuration for client devices, such as the Router. If you are unsure, check with your ISP. To enable IGMP service to the LAN interface, select Enabled and click the Apply button. DVA-G3340S User Manual Page 81 of 94 V1.
Test Tools > Test The Test menus are used to test connectivity of the Router. This diagnostics feature executes a series of test of your system software and hardware connections. Use this Diagnostic Test when working with your ISP to troubleshoot problems. Diagnostic Test Menu DVA-G3340S User Manual Page 82 of 94 V1.
Status Information Use the various read-only menus to view system information and monitor performance. Device Information Display Status > Device Info Use the Device Information window to quickly view basic current information about the LAN and WAN interfaces and device information including Firmware Version and MAC address. Device Information display DVA-G3340S User Manual Page 83 of 94 V1.
DHCP Clients Info Status > DHCP Clients To view DHCP clients that are configured on the Router click DHCP Clients under the Status tab. DHCP Client Info list DVA-G3340S User Manual Page 84 of 94 V1.
Log Status > Log The system log displays chronological event log data. Use the navigation buttons to view or scroll log pages. You may also save a simple text file containing the log to your computer. Click the Save Log button and follow the prompts to save the file. Log display Click Clear Log delete the current log information. DVA-G3340S User Manual Page 85 of 94 V1.
Traffic Statistics Status > Statistics Use the Traffic Statistics window to monitor traffic on the Ethernet or ADSL Internet connection. When the Wireless Select the interface for which you want to view packet statistics and the information will appear below. Traffic Statistics information Click Refresh to view traffic information. DVA-G3340S User Manual Page 86 of 94 V1.
ADSL Status > ADSL Use the ADSL Status information and the Test page for troubleshooting the ADSL connection. ADSL Status information DVA-G3340S User Manual Page 87 of 94 V1.
Technical Specifications Key Component Network Processor and ADSL Chipset Voice Chipset Description TI AR7VWi TI TNETV901 Product Feature Network Interface Description One ADSL port RJ-11, inner pair (pin 2,3) Standard Compliance ADSL Standards: ANSI T1.413 Issue 2 ITU G.992.1 (G.dmt) AnnexA ITU G.992.2 (G.lite) Annex A ITU G.994.1 (G.hs) ADSL2 Standards: ITU G.992.3 (G.dmt.bis) Annex A ITU G.992.4 (G.lite.bis) Annex A Line Rate ADSL2+ Standards: ITU G.992.
Telephone dialing mode support DTMF Dial Pulse (20pps/10pps) Ringer Equivalency Number REN=5 Line Impedance 600ohm Wireless Access Point Embedded Standard Compliance IEEE 802.11 IEEE 802.11b IEEE 802.11g Radio and Modulation Type Operating Frequency IEEE 802.11b: DQPSK, DBPSK, DSSS, and CCK IEEE 802.11g: BPSK, QPSK, 16QAM, 64QAM, OFDM 2400 ~ 2484.
Classical IP over ATM (RFC1577) IPv4 TCP/UDP ARP ICMP IP Routing DHCP RIP v1 (RFC 1058), RIP v2 (RFC 1389) IP Static Routing DHCP Server (RFC2131) DHCP Client (RFC2131) DNS DNS Cache Dynamic DNS IP multicast IGMP Proxy IGMP Snooping ATM/ADSL Multiple PVC Support 8 PVCs ATM Cell format ITU-T Rec. I.361 ATM Adaptation Layer AAL5 ATM signaling ATM Forum UNI3.1/4.
Port Number Setting:- Possible to assign the range- Possible to set TCP/UDP/Both as the protocol Pass Through IPSec/L2TP/PPTP pass through NAT ALGs MSN MSGR FTP SIP (Video/ Audio/ White Board/ Remote Control) ICQ for File and Audio transfer NetMeeting 3/ 2.
DTMF Relay RFC2833 Country Tone Support DT , RBT , BT，Howler／HST(future support) DTMF Tone Detection Modem/Fax: V.21,V.25 PSTN Life-line Function Caller ID Life-line Backup RTP/RTCP Configuration/Manageme nt Access Administration Automatic fall back to PSTN in case of power failure PSTN line automatic selection (e.g.
Operating Temperature 0 °C to 40 °C Storage Temperature -20 °C to 70 °C Operating Humidity Range 5% to 95% Non-condensing Product Feature IP Address/Mask Description 10.1.1.1/255.0.0.0 VPI/VCI 8/35 ADSL Mode Multi-mode Connection Mode PPPoE LLC Web Interface User Name/Password admin/admin DVA-G3340S User Manual Page 93 of 94 V1.
Technical Support You can find software updates and user documentation on the D-Link website. D-Link Australia 1 Giffnock Avenue, North Ryde, NSW 2113 Sydney, Australia TEL: 61-2-8899-1800 FAX: 61-2-8899-1868 Australia: 1300-766-868 New Zealand: 0800-900-900 URL: www.dlink.com.au www.dlink.co.nz E-MAIL: support@dlink.com.au info@dlink.com.au DVA-G3340S User Manual Page 94 of 94 V1.
