Installation guide

ManualsBrandsD-Link ManualsTelephone AccessoriesDVG-2101S

1. If you purchased this VoIP Telephone Adapter to share your high-speed

Internet connection with other computers, you must have an established

Internet account from an Internet Service Provider (ISP).

2. It’s best to use the same computer that is connected to your router for

configuring the DVG-2101S VoIP Telephone Adapter. The DVG-2101S acts

as a DHCP Client and will be assigned all the necessary IP address

information from your network. See the Quick Installation Guide or the Manual

on the CD-ROM for setting each network adapter to automatically obtain an

IP address.

Check Your Package Contents

If any of the above items are missing, please contact your reseller.

respective holders. Software and specifications subject to change without notice.

G-2101S

VoIP Telephone Adapter

Before You Begin

This product can be set up

using any current web browser,

i.e., Internet Explorer 6 or

Netscape Navigator 6.2.3.

D-Link D

G-2101S

oIP Telephone Adapter

CD-ROM (containing Manual and Q.I.G.)

Ethernet Cable

Phone Cable

12V, 1.5A Power Adapter

Quick Installation Guide

Using a power supply

with a different voltage rating

will damage and void the

warranty for this product.

Summary of content (14 pages)

PAGE 1
DVG-2101S This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. VoIP Telephone Adapter Before You Begin 1. If you purchased this VoIP Telephone Adapter to share your high-speed Internet connection with other computers, you must have an established Internet account from an Internet Service Provider (ISP). 2. It’s best to use the same computer that is connected to your router for configuring the DVG-2101S VoIP Telephone Adapter.
PAGE 2
Hardware Overview Front Panel Register LED This LED will light solid if the phone account registers successfully. This LED will flash during registering and light off if registering fails. Power LED This LED will light solid when the device finishes a self-test and booting up. This LED will flash during device self-test and booting and light off if Provision LED This LED will light solid if the device provisions successfully. This LED will flash during provisioning and light off if provisioning fails.
PAGE 3
Rear Panel Reset Button Use a paper clip to: 1. Press 1-2 seconds to enable IVR. 2. Press 4-6 seconds to reset this unit. 3. Press 8-10 seconds to restore this unit’s factory default settings. Phone Port Connects to your phone using a standard phone cable (RJ-11). Power Receptor Connects to the provided power adapter. WAN Port Connects to your broadband modem using an Ethernet cable.
PAGE 4
Configure IP Settings To connect to the network, make sure the network adapter in your computer is configured properly. Here’s how to assign a static IP address to your PC. Go to Start > click Control Panel > click on the Network Connections icon. Click on the Network Connections icon. Right-click the Local Area Connection icon, and then select Properties. Select Properties.
PAGE 5
The dialog box displays a list of currently installed network items. Click Internet Protocol (TCP/IP). Select Properties. Make the choice to get the IP address assigned manually. Select Use the following IP address to get the IP settings assigned manually. Click OK.
PAGE 6
Initial Web Configuration If your computer connects directly to a DSL or Cable modem and does not connect to a router, follow the steps below to install your DVG-2101S. For any other configuration, please refer to the user manual located on the CDROM. After the steps are completed, your setup should look similar to the diagram below. 1. Turn off your Computer. 2. Attach one end of the provided Ethernet cable (blue) to the WAN port on the rear of the DVG-2101S. 3.
PAGE 7
4. Attach one end of the provided phone cable (gray) to a standard analog telephone. 5. Attach the other end of the phone cable to the phone port labeled PHONE on the rear panel of the DVG-2101S. 6. Unpack the 12V DC Power Adapter that came with the DVG-2101S. Connect the power adapter to the power connecter on the DVG-2101S. 7. Connect the other end of the power adapter to an available electrical outlet (wall socket or surge protector). Note: Make sure all the cables are connected tightly and properly.
PAGE 8
Initial Web Configuration Open a Web browser and type http://192.168.1.150 into the URL address box. Press the Enter or Return key. When you first log in, enter the User name admin and leave the Password blank. These may be changed later. Click Login button. Setup Wizard will guide you through the quick setup steps. Click Setup Wizard.
PAGE 9
Click Next. Step 1 You can change the login password during this step or just leave them the same as the default values. Click Next. Step 2 Select your time zone from the drop-down list. Then select a NTP time server or configure your preferred time server. Click Next.
PAGE 10
Step 3-1 If you selected Static IP, enter the IP address, subnet mask and gateway supplied by your ISP. Click Next. Step 3-1-1 Static IP users have to set the DNS address. Click Next. Step 3-1 If you selected Dynamic IP, you may enter the host name in the field. Click Next.
PAGE 11
Step 3-1 If you selected PPPoE, enter your username and password supplied by your ISP. Click Next. Step 4 Enable and configure your SIP account (phone port) with the settings provided by your ISP/ITSP. Click Next. Step 5 Setup is finished. Click Restart to reboot the DVG-2101S. Once the adapter is finished rebooting, turn on your modem and allow up to 2 minutes to connect to your ISP. Click Restart.
PAGE 12
Configuration through IVR The VoIP Adapter provides a convenient IVR (Interactive Voice Response) function to help you query and configure the basic settings of the VoIP Adapter with a phone and without turning on a PC. To access IVR mode, plug a phone into the VoIP Adapter and then pick up the handset and press * (star) 666 # (pound). You will hear voice instructions through the handset. Follow the system’s instructions to set up or query the VoIP Adapter’s settings.
PAGE 13
PAGE 14
Ver.1.