DVG-N5402SP VoIP Wireless Router User’s Manual Version 1.
© 2010 D-Link Corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of D-Link Corporation/D-Link Systems Inc.; Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Contents 1. Introduction .......................................................................................................................................................... 1 1-1 Product Overview ....................................................................................................................................... 1 1-2 Hardware Description ................................................................................................................................. 2 2.
DVG-N5402SP User’s Manual Product Overview 1. Introduction 1-1 Product Overview The DVG-N5402SP is designed to carry both voice and facsimile over the IP network and wirelessly share Internet access. It uses the industry standard SIP call control protocol so as to be compatible with free registration services or VoIP service providers’ systems. As a standard user agent, it is compatible with all common Soft Switches and SIP proxy servers.
DVG-N5402SP User’s Manual Hardware Description 1-2 Hardware Description Front Panel Power: A steady green light indicates a proper connection to a power source. A red light indicates the power-on self test fails or the device is malfunction. Prov/Alm: A blinking light indicates the VoIP Router can not register with SIP Server or can not get the IP address. A blinking light also indicates the VoIP Router is attempting to connect with the Provisioning server.
DVG-N5402SP User’s Manual Hardware Description Rear Panel 1. Antenna: Connect to a wireless network. 2. LINE: Connect to the telephone line on the wall jack through a telephone cable. 3. PHONE2/PHONE1: Connect to your phones through a standard telephone cable. 4. USB: USB host 2.0 port, for connecting to another USB device to supply some value-added application. 5. LAN4/LAN3/LAN2/LAN1: RJ-45 port, for connecting to the Ethernet port of a PC or the Ethernet devices through an Ethernet cable.
DVG-N5402SP User’s Manual SETUP 2. Getting Started To access the Web-based configuration utility, open a Web browser such as IE (Internet Explorer) and enter the IP address of the DVG-N5402SP from LAN port. Open your Web browser and enter http://192.168.0.1 into the URL address bar. Click Enter. Click Login to enter Web site. The default username and password of user account: admin/password . D-Link Systems, Inc.
DVG-N5402SP User’s Manual SETUP 3. VoIP Router Web Configuration (continued) 3-1 SETUP 3-1-1 Wireless Setup This section instructs you how to setup your wireless network on the VoIP Router device. Setup Hint: 1. 2. 3. Every device in the same wireless network must use the same SSID. To avoid wireless network overlap, a specific and different channel is needed. Make sure security used by every device in the same wireless network is compatible with the wireless AP.
DVG-N5402SP User’s Manual SETUP Wireless Network Name (SSID): SSID is the name of your wireless network. All wireless-equipped devices share the same SSID to communicate with each other. It must be unique to identify separated wireless network. For security, you should change the default SSID to a special ID. By default the SSID will be name “DVG-N5402SP-XXXXXX” and “XXXXXX” will be the last 6 numbers of your WAN connection “TR069” MAC Address. Visibility Status: Select the visibility status.
DVG-N5402SP User’s Manual SETUP 3-1-1-2 Wireless Security This section introduces you different ways of wireless security you can set up. It is important to enable secure algorithm to protect your data from eavesdropping by unauthorized wireless users. SETUP → Wireless Setup → Wireless Security Wireless Security Mode: Select the encryption/authentication type: None, WEP, WPA only, WPA2 only, or WPA/WP2 Mixed. D-Link Systems, Inc.
DVG-N5402SP User’s Manual SETUP SETUP → Wireless Setup → Wireless Security (WEP) WEP Key Length: Select 64-bit or 128-bit data encryption. Default Tx Key: You can select one of the keys as active key at a time. WEP Key Format: Select the preferred WEP Key Format according to which WEP encryption you choose. When WEP 64bits is enabled, you can select ASCII (5 characters) and Hex (10 characters). When WEP 128bits is enabled, you can select ASCII (13 characters) and Hex (26 characters).
DVG-N5402SP User’s Manual SETUP WPA Authentication Mode The wireless network can use WPA Authentication to verify whether a wireless device is allowed to access your Access Point or not. You can choose to use Enterprise (RADIUS) method or Personal (Pre-Shared Key). The encryption mechanism used for RADIUS and WPA-PSK is the same. The difference between the two is that WPA-PSK uses a specific characters sting like password instead of a user-authentication.
DVG-N5402SP User’s Manual SETUP SETUP → Wireless Settings → Wireless Security (WPA-Enterprise) If WPA Security Mode is set to WPA (WPA only, WPA2 only, or WPA2 Mixed), you can set WPA Mode to WPA-Enterprise (WPA- Enterprise, WPA2- Enterprise, WPA2 Mixed- Enterprise), select the security mode according to your wireless network. WPA Mode: Select WPA-Enterprise. WPA Cipher Suite: WPA Cipher Suite is used for the configuration of WPA or WPA2 Mixed. TKIP - TKIP is the security protocol used in WPA.
DVG-N5402SP User’s Manual SETUP 3-1-1-3 WPS SETUP → Wireless Setup → WPS Wireless SSID: Select the VAP (Virtual Access Point) of which the WPS function is enabled. Note: There is only one VAP of which the WPS function is enabled each time. If the WPS function of the VAP has been enabled, the WPS function would be disabled before you enable the WPS function of another VAP. Enable: Enable or disable the WPS function.
DVG-N5402SP User’s Manual SETUP 3-1-2 LAN Setup SETUP → LAN Setup Router IP Address: Enter the LAN IP address of the VoIP Router. It is also the default gateway for DHCP clients. Subnet Mask: Enter the subnet mask for DHCP clients. D-Link Systems, Inc.
DVG-N5402SP User’s Manual SETUP SETUP → LAN Setup Enable DHCP Server: This variable is to assign the IP address for the devices connected to LAN port of the VoIP Router. IP Pool Starting Address: Enter the starting IP address for the DHCP server's IP assignment. IP Pool Ending Address: Enter the ending IP address for the DHCP server's IP assignment. DHCP Lease Time: Enter the length of time for the IP lease.
DVG-N5402SP User’s Manual MAINTENANCE 3-2 ADVANCED 3-2-1 Parental Control 3-2-1-1 MAC Filtering Use MAC Filters to deny computers within the local area network from accessing the Internet. You can either manually add a MAC address that are connected to the VoIP Router.
DVG-N5402SP User’s Manual MAINTENANCE 3-2-1-2 IP Filtering Use IP Filters to deny particular LAN IP addresses from accessing the Internet. You can deny specific port numbers or all ports for a specific IP address. The screen will display well-known ports that are defined. To use them, click the edit icon. You will only need to enter the LAN IP address (es) of the computer (s) that will be denied Internet access.
DVG-N5402SP User’s Manual MAINTENANCE 3-2-1-3 Port Filtering Port filtering enables you to control all data that can be transmitted over routers. When the port used at the source end is within the defined scope, it will be filtered without transmission. ADVANCED → Parental Control → Port Filtering Enable Port Filtering: This variable is to restrict certain types of data packets by port. Port Range: Enter the port range that will be denied access to the Internet.
DVG-N5402SP User’s Manual MAINTENANCE 3-2-1-4 URL Filtering URL Filtering is used to block websites (for example, www.yahoo.com). ADVANCED → Parental Control → URL Filtering Enable URL Filtering: Enable or disable the URL function. URL Black Filtering: Users unable to access the website that are listed in the URL Filtering List. URL White Filtering: Users can only access the website that are listed in the URL Filtering List.
DVG-N5402SP User’s Manual MAINTENANCE 3-2-1-5 DHCP Filtering DHCP Filtering is used to control network access based on the IP address of the network device. It is used to deny network or Internet access. ADVANCED → Parental Control → DHCP Filtering Enable DHCP Filter: Enable or disable the DHCP filtering function. ADVANCED → Firewall and DMZ → DHCP Filtering WHITE LIST: Bind the static IP address with the specified MAC address.
DVG-N5402SP User’s Manual MAINTENANCE ADVANCED → Firewall and DMZ → DHCP Filtering BLACK LIST: If the MAC address of the device on the LAN, the VoIP Router does not assign the IP address. MAC: Enter the MAC address of the device on the LAN. 3-2-2 Firewall and DMZ 3-2-2-1 DMZ DMZ (Demilitarized Zone) allows the server on the LAN site to be directly exposed to the Internet for accessing data and to forward all incoming ports to the DMZ Host.
DVG-N5402SP User’s Manual MAINTENANCE Enable DMZ: Check the box to enable DMZ feature. WAN Connection: Select the WAN port that enables DMZ from the drop-down list. Users can access the DMZ host that is provided by this WAN connection through Internet access. DMZ Host IP Address: Enter the IP address of that computer as a DMZ Host with unrestricted Internet access. Note: Either this function or virtual server can be selected for use in accessing external services.
DVG-N5402SP User’s Manual MAINTENANCE 3-2-2-3 Virtual Server Enable users on Internet to access the WWW, FTP and other services from your NAT. It is also known as port forwarding. When remote users are accessing Web or FTP servers through WAN IP address, it will be routed to the server with LAN IP address. ADVANCED → Firewall and DMZ → Virtual Server WAN Connection (s): Select the WAN interface for the Internet connection. Users can access the virtual server through the WAN connection.
DVG-N5402SP User’s Manual MAINTENANCE 3-2-3 Advanced Wireless 3-2-3-1 Advanced This section introduces advanced configuration of the wireless access point. If you are not familiar with the following functions, keep the default parameters. In some cases, incorrect settings may reduce wireless performance. ADVANCED → Advanced Wireless → Advanced Transmission Rate: You can select it from the drop-down list.
DVG-N5402SP User’s Manual MAINTENANCE provides good network performance. In most case, it is recommended to keep the default value: 2346. Preamble Type: It defines the length of the preamble which sends out with a packet format. Specify an appropriate preamble type for your network. If you do not know which one to select, it is recommended to keep the default setting.
DVG-N5402SP User’s Manual MAINTENANCE 3-2-4 Advanced Network 3-2-4-1 ALG ALG (Application Layer Gateway) is also named the third generation firewall. When the user on the trusted network wants to connect to the untrusted network (Internet), the application will be guided to the proxy server of the firewall. The proxy server disguises the actual server on the Internet. It can estimate the request, and decides the permission or deny of the request according to the rule in a suit of unit network service.
DVG-N5402SP User’s Manual MAINTENANCE 3-2-4-2 QoS LAN QoS ADVANCED → Advanced Network → QoS Enable LAN QoS: Check the box to enable LAN QoS by Hardware. Priority: Use the drop-down menu to select Low or HIGH for the VoIP Router to deliver the packets from LAN interface when the packets arrive at the same time. Flow Control: Check the box to limit incoming and outgoing rate. Incoming Rate Limit: Select the proper rate limit for the specific LAN port from the drop-down menu.
DVG-N5402SP User’s Manual MAINTENANCE 3-2-4-3 Static Routing Build static routes within an internal network. These routes will not apply to the Internet. ADVANCED → Advanced Network → Static Routing Destination Network Address: The destination IP address of the router. Subnet Mask: The subnet mask of the destination IP address. Use Gateway IP Address: The gateway IP address of the router. Use Interface: The interface name of the router output port.
DVG-N5402SP User’s Manual MAINTENANCE 3-2-4-4 UPNP ADVANCED → Advanced Network → UPNP Enable UPNP: Check the box to enable the IP traffic of the VOIP Router to pass through an Internet sharing device. D-Link Systems, Inc.
DVG-N5402SP User’s Manual MAINTENANCE 3-2-5 Schedule To access the Schedules window, click the schedules button in the Advanced directory. You can add schedules in this page and then apply them to Parental Control. Name: Enter a Name for the schedule. Day(s): Use the radio buttons to click the desired Day(s), either All Week or Select Day(s) (in which case you must tick the checkboxes for the desired individual days of the week), All Day – 24 hrs: Tick to apply the rules for whole day.
DVG-N5402SP User’s Manual MAINTENANCE 3-3 MAINTENANCE 3-3-1 Device Management MAINTENANCE → Device Management Note: Logging in as user, you can only access to some specific settings of the VoIP Router. Current Password: Enter the password for accessing the VoIP Router. New Password: Modify the password for accessing the VoIP Router. It is highly recommended that you modify the password for securing your VoIP Router. Confirm Password: Enter the modified password again.
DVG-N5402SP User’s Manual MAINTENANCE 3-3-2 Backup and Restore Reboot MAINTENANCE → Backup and Restore →Reboot Reboot: Click the Reboot button to reboot the system. Backup Setting The current system settings can be saved as a file onto the local hard drive. MAINTENANCE → Backup and Restore → Backup Setting Backup Setting: Click the Backup Settings button to save all current settings to a file on your PC. D-Link Systems, Inc.
DVG-N5402SP User’s Manual MAINTENANCE Update Setting MAINTENANCE → Backup and Restore → Update Setting To restore the system settings file, click the Browse button to search the local hard drive for the file to be used. Once you locate the file, click the Upload Setting button to overwrite the current settings with the settings saved to the file.
DVG-N5402SP User’s Manual MAINTENANCE 3-3-3 Dynamic DNS ADVANCED → Dynamic DNS Enable Dynamic DNS: Check the box to enable DDNS (Dynamic Domain Name Server) function. It is only necessary when the VoIP Router is set up behind an Internet sharing device that uses a dynamic IP address and does not support DDNS. Wan Connection: Select the WAN connection that you want to configure DDNS. Server Address: Select a DDNS service from the drop-down menu.
DVG-N5402SP User’s Manual MAINTENANCE Password or Key: Enter the password for logging into the DDNS server. Verify Password or Key: Enter the password again for confirmation. 3-3-4 USB File Sharing over FTP MAINTENANCE → USB File Sharing over FTP Enabled FTP Server: Select the check box to enable the FTP server. FTP Server Status: The current status of FTP server. User Name: Enter the user name that accesses the FTP server. Password: Enter the password that accesses the FTP server.
DVG-N5402SP User’s Manual MAINTENANCE 3-3-5 Diagnostics 3-3-5-1 Ping In this page, you can use ping to verify whether a remote peer is reachable. MAINTENANCE → Diagnostics → Ping Ping Destination: Enter the IP address or domain name for ping. Number of Ping: Enter the number of ping. Its range is in 1 to 100. Ping Packet Size: Set the packet size for ping. Its range is in 1 to 5600. D-Link Systems, Inc.
DVG-N5402SP User’s Manual MAINTENANCE 3-3-5-2 Traceroute MAINTENANCE → Diagnostics → Traceroute Host: Enter the IP address or domain name for testing. Max TTL: Set the survival time of the data packets during testing. Its range is in 1 to 128. Wait times: Set the waiting time during testing. Its range is in 2 to 60. D-Link Systems, Inc.
DVG-N5402SP User’s Manual STATUS 3-4 STATUS 3-4-1 Device Info STATUS → Device Info For WAN Port Information, it shows IP address, subnet mask, default gateway and Domain name server. If you use PPPoE to obtain IP, you will know if the IP is obtained through this method. If IP address, subnet mask, default gateway is blank, it means that the VoIP Router does not obtain IP. D-Link Systems, Inc.
DVG-N5402SP User’s Manual STATUS For LAN Port Information, it shows LAN port IP, subnet mask, and the MAC address. For Hardware, it shows the hardware platform and driver version. D-Link Systems, Inc.
DVG-N5402SP User’s Manual STATUS 3-4-2 VoIP Status STATUS → VoIP Status For Port Status, it includes if each port registers to Proxy successfully, the last dialed number, how many calls each port has made since the VoIP Router is start, etc. D-Link Systems, Inc.
DVG-N5402SP User’s Manual STATUS 3-4-3 LAN Client STATUS → LAN Client The LAN CLIENTS table displayed the local LAN information. The ACTIVE WIRELESS CLIENTS table displayed the identification and transmission status of active wireless clients on wireless LAN interface. The DHCP CLIENTS table displayed LAN device that has already been assigned an address from DVG-N5402SP. You can check if the DHCP client has obtain an IP address. D-Link Systems, Inc.
DVG-N5402SP User’s Manual STATUS 3-4-4 Statistics STATUS → Statistics It displays the information of the last call made. Press Refresh button to get the latest RTP Packet Summary. D-Link Systems, Inc.
DVG-N5402SP User’s Manual STATUS 3-4-5 Logout STATUS → Logout If setting or parameter has been changed, remember to save the changes before you logout the configuration menu. D-Link Systems, Inc.
DVG-N5402SP User’s Manual Appendix Appendix Product Features WAN • One 10/100/1000Mbps auto-negotiation, auto-crossover RJ-45 Ethernet port • Support Static IP, DHCP, PPPoE, PPTP, L2TP, 3G USB Adapter, and Bridge.
DVG-N5402SP User’s Manual • • • • Appendix o IVR o Telnet Status reports: o Port status o Registration status o Ping tests o Hardware / software information Firmware Upgrade through LOCAL, TFTP, FTP, HTTP, HTTPS server Configuration Backup/Restore Reset button (with restore factory default function) D-Link Systems, Inc.
