Setup guide

5305,5310,5315,5320,5325,5330,5335,5340,5345,5350,5355,
5360,5365,5370,5375,5380,5385,5390,5395,5400,5405,5410,
5415,5420,5425,5430,5435,5440,5445,5450,5455,5460,5465,
5470,5475,5480,5485,5490,5495,5500,5505,5510,5515,5520,
5525,5530,5535,5540,5545,5550,5555,5560,5565,5570,5575,
5580,5585,5590,5595,5600,5605,5610,5615,5620,5625,5630,
5635,5640,5645,5650,5655,5660,5665,5670,5675,5680,5685,
5690,5695,5700,5705,5710,5715,5720,5725,5730,5735,5740,
5745,5750,5755,5760,5765,5770,5775,5780,5785,5790,5795,
5800,5805,5810,5815,5820,5825,5830,5835,5840,5845,5850,
5855,5860,5865,5870,5875,5880,5885,5890,5895,5900,5905,
5910,5915,5920,5925,5930,5935,5940,5945,5950,5955,5960,
5965,5970,5975,5980,5985,5990,5995,6000,6005,6010,6015,
6020,6025,6030,6035,6040,6045,6050,6055,6060,6065,6070,
6075,6080,6085,6090,6095,6100
2GHz-G-channels=2312,2317,2322,2327,2332,2337,2342,2347,2352,2357,2362,2367,
2372,2412,2417,2422,2427,2432,2437,2442,2447,2452,2457,2462,
2467,2472,2512,2532,2552,2572,2592,2612,2632,2652,2672,2692,
2712,2732,2484
[admin@Wandy] interface wireless>
Virtual Access Point Interface
interface wireless
Description
Virtual Access Point (VAP) interface is used to have an additional AP. You can create a new AP
with different ssid. It can be compared with a VLAN where the ssid from VAP is the VLAN tag
and the hardware interface is the VLAN switch.
Note that you cannot use the Virtual Access Point on Prism based cards!
Property Description
802.1x-mode (PEAP-MSCHAPV2 | none) - to use Protected Extensible Authentication Protocol
Microsoft Challenge Handshake Authentication Protocol version 2 for authentication
arp (disabled | enabled | proxy-arp | reply-only) - ARP mode
mac-address (read-only: MAC address; default: 00:00:00:00:00:00) - MAC address of VAP. Is
assigned automatically when the field master interface is set
default-authentication (yes | no; default: yes) - whether to accept or reject a client that wants to
associate, but is not in the access-list
default-forwarding (yes | no; default: yes) - whether to forward frames to other AP clients or not
disable-running-check (yes | no; default: no) - disable running check. For 'broken' cards it is a
good idea to set this value to 'yes'
disabled (yes | no; default: yes) - whether to disable the interface or not
hide-ssid (yes | no; default: no) - whether to hide ssid or not in the beacon frames:
• yes - ssid is not included in the beacon frames. AP replies only to probe-requests with the given
ssid
• no - ssid is included in beacon frames. AP replies to probe-requests with the given ssid and to
'broadcast ssid'
master-interface (name) - hardware interface to use for VAP
max-station-count (integer; default: 2007) - number of clients that can connect to this AP