D-Link AirPlus G™ DWL-G730AP 802.11g/2.
Contents Package Contents ................................................................................ 3 Introduction ........................................................................................... 4 Wireless Basics .................................................................................... 6 Hardware Overview .............................................................................. 8 Getting Started in AP Mode ..................................................................
Package Contents Contents of Package: D-Link AirPlusTM G DWL-G730AP 802.11g/2.4GHz Wireless Pocket Router/AP Power Supply - 5V DC, 1.2A Manual on CD Quick Installation Guide Ethernet Cable USB Power Cable Travel Case If any of the above items are missing, please contact your reseller. Note: Using a power supply with a different voltage rating than the one included with the DWL-G730AP will cause damage and void the warranty for this product.
Introduction The pocket-sized DWL-G730AP gives you all the features of a full-size router/access point with pocket-size convenience and portability. Carry it along with you on business trips and vacations, and experience the convenience of wireless networking with your colleagues and family almost anywhere you travel. With 3 different operating modes, the versatile DWL-G730AP can be used as a portable access point, AP client or router.
Features and Benefits Up to 5X Faster with AirPlus G Products - maximum wireless signal rate up to 54Mbps.* With increased data rate and capacity, the DWL-G730AP delivers media rich content such as digital images, videos, and MP3 files much faster than standard 802.11b networks. Fully 802.11b Compatible – Fully compatible with the IEEE 802.11b standard and interoperable with all existing 802.11b compliant devices.
Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. D-Link wireless products will allow you access to the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking brings. A Wireless Local Area Network (WLAN) is a computer network that transmits and receives data with radio signals instead of wires.
Wireless Basics (continued) Installation Considerations Keep in mind, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business.
Hardware Overview Top Panel Power LED: Solid indicates a connection to a good power source. LAN LED: Solid indicates an Ethernet connection. Blinking indicates activity on the Ethernet network. WLAN LED: A solid light indicates that the wireless segment is ready. This LED blinks during wireless data transmission. Mode Selection Switch: Used to select AP, client, or router mode. Rear Panel Receptor for Power Adapter Reset Button: Used to restore default settings.
Getting Started - in AP mode An Example of a Wireless Infrastructure Network 1 2 3 4 5 6 Please remember that D-Link AirPlus G wireless devices are pre-configured to connect together, right out of the box, with their default settings.
Getting Started - in Client mode An Example of a Wireless Infrastructure Network 1 2 3 4 Please remember that D-Link AirPlus G wireless devices are pre-configured to connect together, right out of the box, with their default settings.
Getting Started - in Router mode An Example of a Wireless Infrastructure Network 2 1 3 4 5 Please remember that D-Link AirPlus G wireless devices are pre-configured to connect together, right out of the box, with their default settings. For a typical wireless setup at home (as shown above), please do the following: You will need broadband Internet access (a Cable or DSL-subscriber line into your home or office) Consult with your Cable or DSL provider for proper installation of the modem.
Using the Configuration Utility in AP Mode After you have completed the initial installation and the Setup Wizard (as illustrated in the Quick Installation Guide that is included with the DWL-G730AP), and you have selected AP Mode, you can access the configuration menu, at any time, by opening the web-browser and typing in the IP address of the DWL-G730AP. The DWL-G730AP’s default IP address is shown below: Open the web browser Type in the IP address of the DWL-G730AP. (192.168.0.30). http://192.168.0.
Using the Configuration Utility in AP Mode (continued) Home > Wireless Hexadecimal digits consist of the numbers 0-9 and the letters A-F ASCII (American Standard Code for Information Interchange) is a code for representing English letters as numbers from 0127 SSID: (Service Set Identifier) default is the default setting. The SSID is a unique name that identifies a network. All devices on a network must share the same SSID name in order to communicate on the network.
Using the Configuration Utility in AP Mode (continued) Home > Wireless > WPA SSID: (Service Set Identifier) Default is the default setting. The SSID is a unique name that identifies a network. All devices on a network must share the same SSID name in order to communicate on the network. If you choose to change the SSID from the default setting, input your new SSID name in this field. Channel: Channel 6 is the default channel. Input a new number if you want to change the default setting.
Using the Configuration Utility in AP Mode (continued) Home > Wireless > WPA-PSK SSID: (Service Set Identifier) Default is the default setting. The SSID is a unique name that identifies a network. All devices on a network must share the same SSID name in order to communicate on the network. If you choose to change the SSID from the default setting, input your new SSID name in this field. Channel: Channel 6 is the default channel. Input a new number if you want to change the default setting.
Using the Configuration Utility in AP Mode (continued) Home > LAN Dynamic IP Address: Select this option if you would like to have an IP Address automatically assigned to the DWL-G730AP by a DHCP server in your network. DHCP stands for Dynamic Host Configuration Protocol. It is a protocol for assigning dynamic IP addresses “automatically.” With a DHCP Server there is no need to manually assign an IP Address. Static IP Address: Select this option if you are manually assigning an IP address. IP Address: 192.
Using the Configuration Utility in AP Mode (continued) Home > DHCP DHCP Server: Select Enabled or Disabled. Disabled is the default setting. If you want to use the DWL-G730AP as a DHCP server, to automatically assign dynamic IP addresses on the network, you will select Enabled. Starting IP Address: If you have enabled the DHCP server function, enter the starting point of the IP address range for your network.
Using the Configuration Utility in AP Mode (continued) Beacon Interval: Beacons Advanced > Performance are packets sent by an access point to synchronize a wireless network. Specify a beacon interval value. Default (100) is recommended. RTS Threshold: This value should remain at its default setting of 2432. If you encounter inconsistent data flow, only minor modifications to the value range between 256 and 2432 are recommended. Fragmentation: This value should remain at its default setting of 2346.
Using the Configuration Utility in AP Mode (continued) Advanced > Filters Use MAC Filters to allow or deny wireless clients (identified by their MAC addresses) access to the DWL-G730AP. You can manually add a MAC address or select the MAC address from the list of clients that are currently connected to the router (Connected PCs). The default setting is Disabled MAC Filters.
Using the Configuration Utility in AP Mode (continued) Tools > Admin New Password: Enter the new password. Confirm Password: Re-enter the password to confirm it. Save Settings: The current Tools > System system settings can be saved as a file onto the local hard drive. Load Settings: The saved file or any other saved setting file can be loaded back on the access point. To reload a system settings file, click on Browse to browse the local hard drive and locate the system file to be used.
Using the Configuration Utility in AP Mode (continued) Tools > Firmware You can upgrade the firmware of the DWL-G730AP on this page. When you click Click here to check... in this window you will be connnected to D-Link’s website, where you can download the latest firmware update. After you have completed the firmware download to your hard drive, click Browse to browse your local hard drive and locate the firmware to be used for the update. Click Apply.
Using the Configuration Utility in AP Mode (continued) Status > Log View Log The DWL-G730AP keeps a running log of events and activities occurring on the AP. If the device is rebooted, the logs are automatically cleared. You may save the log files under Log Setting. First Page - The first page of the log. Last Page - The last page of the log. Previous - Moves back one log page. Next - Moves forward one log page. Clear - Clears the logs completely. Log Settings - Brings up the page to configure the logs.
Using the Configuration Utility in AP Mode (continued) Status> Stats Traffic Statistics The DWL-G730AP keeps statistics of traffic that passes through it. You are able to view the amount of packets that pass through the Ethernet and wireless portions of the network. The traffic counter will reset if the device is rebooted. Connected Wireless PCs List Status > Wireless This list displays the MAC addresses of connected PCs and the length of time that they have been connected.
Using the Configuration Utility in AP Client Mode Whenever you want to configure your network or the DWL-G730AP, you can access the Configuration Menu by opening the Web browser and typing in the IP address of the DWL-G730AP. The DWL-G730AP default IP address is shown at right. Open the Web browser Type in the IP address of the AP Client (http://192.168.0.30) Note: if you have changed the default IP address assigned to the DWL-G730AP, make sure to enter the correct IP address.
Using the Configuration Utility in AP Client Mode (continued) Home > Wireless SSID- Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID’s factory default setting is default. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. Channel6 is the default channel. All devices on the network must share the same channel.
Using the Configuration Utility in AP Client Mode (continued) Home > Wireless > WPA-PSK SSID- Service Set Identifier (SSID) is the name designated for a specific wirelesslocal area network (WLAN). The SSID’s factory default setting is default. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. Click Site Survey to view the available networks. Channel6 is the default channel. All devices on the network must share the same channel.
Using the Configuration Utility in AP Client Mode (continued) Home > LAN LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DWL-G730AP. These settings may be referred to as private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. IP Address- The IP address of the LAN interface. The default IP address is: 192.168.0.
Using the Configuration Utility in AP Client Mode (continued) Advanced > Performance Beacon Interval: Beacons are packets sent by an access point to synchronize a wireless network. Specify a beacon interval value. Default (100) is recommended. RTS Threshold: This value should remain at its default setting of 2432. If you encounter inconsistent data flow, only minor modifications to the value range between 256 and 2432 are recommended. Fragmentation: This value should remain at its default setting of 2346.
Using the Configuration Utility in AP Client Mode (continued) Tools > Admin Administrator Settings Enter the password. New PasswordConfirm Password- Enter the password again.
Using the Configuration Utility in AP Client Mode (continued) Tools > System The current system settings can be saved as a file onto the local hard drive. To reload a system settings file, click on Browse to browse the local hard drive and locate the system file to be used.
Using the Configuration Utility in AP Client Mode (continued) Tools > Firmware You can upgrade the firmware of the router here. Make sure the firmware you want to use is on the local hard drive of the computer. Check the D-Link support site for firmware updates at http://support.dlink.com and download firmware upgrades to your hard drive. After you have downloaded the firmware upgrade to your hard drive, click Browse to browse the local hard drive and locate the firmware to be used for the update.
Using the Configuration Utility in AP Client Mode (continued) Status > Device Info This screen displays the current firmware version, and the current wireless and Ethernet settings of the DWL-G730AP.
Using the Configuration Utility in AP Client Mode (continued) Status > Stats This screen displays theTraffic Statistics. Here you can view the amount of packets that pass through the DWL-G730AP on both the Ethernet and the wireless networks. The traffic counter will reset if the device is rebooted.
Using the Configuration Utility in AP Client Mode (continued) Help The Help menu is displayed here. Click on a topic to learn more about it.
Using the Configuration Utility in Router Mode To configure the DWL-G730AP in Router mode, you must be connected to the router via a wireless network adapter. The LAN Port on the unit functions as a WAN port when the DWL-G730AP is operating in Router mode. To run the setup wizard, establish a wireless connection with the DWL-G730AP and follow the steps below. To use the DWL-G730AP as a router, toggle the switch on the back of the unit. Open the Web browser Type in the IP address of the router (http://192.
Using the Configuration Utility in Router Mode (continued) Home > Wireless SSIDService Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID’s factory default setting is default. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. Channel- 6 is the default channel. All devices on the network must share the same channel.
Using the Configuration Utility in Router Mode (continued) Home > Wireless > WPA-PSK SSID: (Service Set Identifier) default is the default setting. The SSID is a unique name that identifies a network. All devices on a network must share the same SSID name in order to communicate on the network. If you choose to change the SSID from the default setting, input your new SSID name in this field. Channel: Channel 6 is the default channel. Input a new number if you want to change the default setting.
Using the Configuration Utility in Router Mode (continued) Home > WAN > Dynamic IP Address Dynamic IP Address is selected here. Other options include: Static IP Address (if your ISP provides you with a static IP address), PPPoE (for most DSL users), PPTP (for Europe) and BigPond Cable (for Australia). Dynamic IP Address- Choose Dynamic IP Address to obtain an IP address automatically. Host Name- The Host Name is optional but may be required by some ISPs.
Using the Configuration Utility in Router Mode (continued) Home > LAN LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DWL-G730AP. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. IP Address- The IP address of the LAN interface. The default IP address is: 192.168.0.
Using the Configuration Utility in Router Mode (continued) Home > DHCP DHCP stands for Dynamic Host Control Protocol. The DWL-G730AP has a builtin DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DWL-G730AP.
Using the Configuration Utility in Router Mode (continued) Advanced > Virtual Server The DWL-G730AP can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DWL-G730AP firewall feature filters out unrecognized packets to protect your LAN network so all computers networked with the DWL-G730AP are invisible to the outside world.
Using the Configuration Utility in Router Mode (continued) Advanced > Virtual Server (continued) Virtual Server- Select Enabled or Disabled. Name- Enter the name referencing the virtual service. Private IP- The server computer in the LAN (Local Area Network) that will be providing the virtual services. Protocol Type- The protocol used for the virtual service. Private Port- The port number of the service used by the Private IP computer.
Using the Configuration Utility in Router Mode (continued) Advanced > Virtual Server (continued) Click on this icon to edit the virtual service Click on this icon to delete the virtual service Example #2: If you have an FTP server that you wanted Internet users to access by WAN port 2100 and only during the weekends, you would need to enable it as such. FTP server is on LAN computer 192.168.0.30. FTP uses port 21, TCP. Name: FTP Server Private IP: 192.168.0.
Using the Configuration Utility in Router Mode (continued) Advanced > Applications Some applications such as Internet gaming, video conferencing, Internet telephony and others, require multiple connections. These applications save difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DWL-G730AP.
Using the Configuration Utility in Router Mode (continued) Advanced > Filters > IP Filters Filters are used to deny or allow LAN (Local Area Network) computers from accessing the Internet. The DWL-G730AP can be setup to deny internal computers by their IP or MAC addresses. The DWL-G730AP can also block users from accessing restricted web sites. IP Filters: Use IP Filters to deny LAN IP addresses from accessing the Internet. You can deny specific port numbers or all ports for the specific IP address.
Using the Configuration Utility in Router Mode (continued) Advanced > Filters > URL Blocking URL Blocking: Select Enable or Disable. Enter the words or word contained in the URL that you wish to block. Click Apply to activate the URL blocking. Delete: Select the URL block that you want to delete. Click Delete. Apply: Click Apply to save changes.
Using the Configuration Utility in Router Mode (continued) Advanced > Filters > MAC Filters Disable MAC Filters: Click to Disable MAC Filters. Allow: Allow only those devices with the listed MAC addresses access to the network. Deny: Deny the devices that are listed from accessing the network. Name: Enter a name for the device. Clear: Click Clear to erase the name. MAC Address: Enter the MAC address manually.
Using the Configuration Utility in Router Mode (continued) Advanced > Filters > Domain Blocking Disable: Click Disable to disable domain blocking. Allow: Click Allow to allow access to all domains except Blocked Domains. Deny: Click Deny to deny access to all domains except Permitted Domains. Permitted Domains: Enter the permitted domains here. Click Apply. Blocked Domains: Enter the blocked domains here. Click Apply.
Using the Configuration Utility in Router Mode (continued) Advanced > Firewall Firewall Rules is an advanced feature used to deny or allow traffic from passing through the DWLG730AP. It works in the same way as IP Filters with additional settings. You can create more detailed access rules for the DWL-G730AP. When virtual services are created and enabled, it will also display in Firewall Rules. Firewall Rules contain all network firewall rules pertaining to IP (Internet Protocol).
Using the Configuration Utility in Router Mode (continued) Advanced > DMZ 30 If you have a client PC that cannot run Internet applications properly from behind the DWL-G730AP, then you can set the client up for unrestricted Internet access. Allowing a computer to be exposed to the Internet, this feature is useful for gaming purposes. Enter the IP address of the internal computer that will be the DMZ host.
Using the Configuration Utility in Router Mode (continued) Advanced > Performance Beacon Interval: Beacons are packets sent by an access point to synchronize a wireless network. Specify a beacon interval value. Default (100) is recommended. RTS Threshold: This value should remain at its default setting of 2432. If you encounter inconsistent data flow, only minor modifications to the value range between 256 and 2432 are recommended. Fragmentation: This value should remain at its default setting of 2346.
Using the Configuration Utility in Router Mode (continued) Tools > Admin At this page, the DWL-G730AP administrator can change the system password. There are two accounts that can access the router’s Web-management interface. They are admin and user. Admin has read/write access while user has read-only access. The user can only view the settings but cannot make any changes.
Using the Configuration Utility in Router Mode (continued) Tools > Time Time ZoneDefault NTP Server- Select the time zone from the pull-down menu. NTP is short for Network Time Protocol. NTP synchronizes computer clock times in a network of computers. This field is optional. Set the Time- To manually input the time, enter the values in these fields for the year, month, day, hour, minute, and second. Click Set Time.
Using the Configuration Utility in Router Mode (continued) Tools > System The current system settings can be saved as a file onto the local hard drive. To reload a system settings file, click on Browse to browse the local hard drive and locate the system file to be used.
Using the Configuration Utility in Router Mode (continued) Tools > Firmware You can upgrade the firmware of the router here. Make sure the firmware you want to use is on the local hard drive of the computer. Please check the D-Link support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site.
Using the Configuration Utility in Router Mode (continued) Tools > Misc Ping Test- The ping test is used to send ping packets to test if a computer is on the Internet. Enter the IP address that you wish to ping, and click Ping. Restart Device- Click Reboot to restart the DWL-G730AP. Block WAN Ping- If you choose to block WAN ping, the WAN IP address of the DWL-G730AP will not respond to pings. Blocking the ping may provide some extra security from hackers.
Using the Configuration Utility in Router Mode (continued) Status > Device Info This page displays the current information for the DWL-G730AP. It will display the LAN, WAN and MAC address information. If your WAN connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your WAN connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed.
Using the Configuration Utility in Router Mode (continued) Status > Log View Log displays the activities occurring on the DWL-G730AP. Click on Log Settings for advance features. The DWL-G730AP keeps a running log of events and activities. If the device is rebooted, the logs are automatically cleared. You may save the log files under Log Settings.
Using the Configuration Utility in Router Mode (continued) Status > Stats This screen displays theTraffic Statistics. Here you can view the amount of packets that pass through the DWL-G730AP on both the WAN and the LAN ports. The traffic counter will reset if the device is rebooted. Click Refresh to view the latest statistics. Click Reset to reset. Status > Wireless The wireless client table displays a list of current connected wireless clients.
Networking Basics Using the Network Setup Wizard in Windows XP In this section you will learn how to establish a network at home or work, using Microsoft Windows XP. Note: Please refer to websites such as http://www.homenethelp.com and http://www.microsoft.com/windows2000 for information about networking computers using Windows 2000, Me or 98SE. Go to Start>Control Panel>Network Connections Select Set up a home or small office network When this screen appears, click Next.
Networking Basics (continued) Please follow all the instructions in this window: Click Next. In the following window, select the best description of your computer. If your computer connects to the internet through a gateway/router, select the second option as shown. Click Next.
Networking Basics (continued) Enter a Computer description and a Computer name (optional.) Click Next. Enter a Workgroup name. All computers on your network should have the same Workgroup name. Click Next.
Networking Basics (continued) Please wait while the Network Setup Wizard applies the changes. When the changes are complete, click Next. Please wait while the Network Setup Wizard configures the computer. This may take a few minutes.
Networking Basics (continued) In the window below, select the option that fits your needs. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next. Insert a disk into the Floppy Disk Drive, in this case drive A.
Networking Basics (continued) Please wait while the Network Setup Wizard copies the files. Please read the information under Here’s how in the screen below. After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network. To continue click Next.
Networking Basics (continued) Please read the information on this screen, then click Finish to complete the Network Setup Wizard. The new settings will take effect when you restart the computer. Click Yes to restart the computer. You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network. After running the Network Setup Disk on all your computers, your new wireless network will be ready to use.
Networking Basics (continued) Naming your Computer To name your computer, please follow these directions:In Windows XP: Click Start (in the lower left corner of the screen). Right-click on My Computer. Select Properties and click. Select the Computer Name Tab in the System Properties window. You may enter a Comput- er Description if you wish; this field is optional. To rename the computer and join a domain, Click Change.
Networking Basics (continued) Naming your Computer In this window, enter the Computer name. Select Workgroup and enter the name of the Workgroup. All computers on your network must have the same Workgroup name. Click OK. Checking the IP Address in Windows XP The wireless adapter-equipped computers in your network must be in the same IP Address range (see Getting Started in this manual for a definition of IP Address Range.
Networking Basics (continued) Checking the IP Address in Windows XP This window will appear. Click the Support tab. Click Close. Assigning a Static IP Address in Windows XP/2000 Note: Residential Gateways/Broadband Routers will automatically assign IP Addresses to the computers on the network, using DHCP (Dynamic Host Configuration Protocol) technology. If you are using a DHCP-capable Gateway/Router you will not need to assign Static IP Addresses.
Networking Basics (continued) Assigning a Static IP Address in Windows XP/2000 Double-click on Network Connections. Right-click on Local Area Connections. Double-click on Properties.
Networking Basics (continued) Assigning a Static IP Address in Windows XP/2000 Click on Internet Protocol (TCP/IP). Click Properties. Select Use the following IP address in the Internet Protocol (TCP/IP) Properties window (shown below) In the window below, select Use the following IP address. Input your IP address and subnet mask. (The IP addresses on your network must be within the same range. For example, if one computer has an IP address of 192.168.0.
Networking Basics (continued) Checking the Wireless Connection by Pinging in Windows XP/2000 Go to Start > Run > type cmd. A window similar to this one will appear. Type ping xxx.xxx.xxx. xxx, where xxx is the IP address of the wireless router or access point. A good wireless connection will show four replies from the wireless router or access point, as shown. Checking the Wireless Connection by Pinging in Windows Me /98SE Go to Start > Run > type command. A window similar to this will appear.
Technical Specifications Standards • IEEE 802.11b • IEEE 802.11g • IEEE 802.3 • IEEE 802.3u Device Management • Web-Based – Internet Explorer v6 or later; Netscape Navigator v7 or later; or other Java-enabled browsers. Data Rates* For 802.11g: • 54, 48, 36, 24, 18, 12, 9 and 6Mbps For 802.11b: • 11, 5.5, 2, and1Mbps Security • 64-, 128-bit WEP • WPA – Wi-Fi Protected Access • MAC Address Filtering • SSID Broadcast Disable Wireless Frequency Range • 2.412GHz to 2.462GHz Wireless Operating Range* 802.
Technical Specifications (continued) Radio and Modulation Type For 802.11g: OFDM: • BPSK @ 6 and 9Mbps • QPSK @ 12 and 18Mbps • 16QAM @ 24 and 36Mbps • 64QAM @ 48 and 54Mbps DSSS: • DBPSK @ 1Mbps • DQPSK @ 2Mbps • CCK @ 5.5 and 11Mbps For 802.11b: DSSS: • DBPSK @ 1Mbps • DQPSK @ 2Mbps • CCK @ 5.5 and 11Mbps Wireless Transmit Power Typical RF Output Power at each Data Rate For 802.11g: • 31mW (15dBm) @ 54Mbps • 40mW (16dBm) @ 48Mbps • 40mW (16dBm) @ 36, 24, 18, 12, 9, and 6Mbps For 802.
Technical Specifications (continued) LEDs • Power • LAN • WLAN Temperature • Operating: 32ºF to 131ºF (0ºC to 55ºC) • Storing: -4ºF to 149ºF (-20ºC to 65ºC) Humidity • Operating: 10%~90% (non-condensing) • Storing: 5%~95% (non-condensing) Certifications • FCC • CE Dimensions • L = 3.15 inches (80mm) • W = 2.36 inches (60mm) • H = 0.67 inches (17mm) Weight • 0.
Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone. Tech Support for customers within the United States: D-Link Technical Support over the Telephone: (877) 453-5465 24 hours a day, seven days a week.
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited warranty for its product only to the person or entity that originally purchased the product from: • D-Link or its authorized reseller or distributor and • Products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, addresses with an APO or FPO.
• The original product owner must obtain a Return Material Authorization (“RMA”) number from the Authorized D-Link Service Office and, if requested, provide written proof of purchase of the product (such as a copy of the dated purchase invoice for the product) before the warranty service is provided.
Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This limited warranty provides specific legal rights and the product owner may also have other rights which vary from state to state. Trademarks: D-Link is a registered trademark of D-Link Systems, Inc.
