DWL-AG700AP Install Guide
DWL-AG700AP Install Guide DWL-AG132 Install Guide Contacting Technical Support System Requirements System Requirements Minimum System Requirements: Computers with Windows XP/2000 operating system with an available USB 2.0 port Internet Explorer version 6.0 or Netscape Navigator version 7.0 and above Package Contents D-Link AirPremier AG DWL-AG132 Wireless AG USB 2.0 Adapter Manual on CD Cradle D-Link Systems, Inc.
Installing thetoDrivers Connecting DWL-AG132 your Install network Guide DWL-AG132 Install Guide Installing the Drivers DWL-AG700AP Install Guide Installing the Drivers Do NOT install the DWL-AG132 Wireless AG USB Adapter into your computer before installing the driver software from the D-Link CD! The step-by-step instructions that follow are shown in Windows XP. The steps and screens are similar for the other Windows operating systems.
Installing Drivers Using the the Setup Wizard DWL-AG132 Install Guide DWL-AG700AP Installing the Drivers (continued) Click Next Click ‘Yes, I want to restart my computer now.’ Click Finish You have completed the installation of the drivers! D-Link Systems, Inc.
Connecting the DWL-AG132 DWL-AG132 Install Guide Connecting the DWL-AG132 USB Port - used to connect the DWLAG132 to your computer. Link/Power LED Link - indicates that the DWL-AG132 is properly installed. Activity - blinks when data is being transmitted through the wireless connection. Remove the protective covering from the DWL-AG132. Begin by pressing down on the cover with your thumb. Pull the cover away from the DWL-AG132. Insert the DWL-AG132 into an available USB port on your computer.
The Found New Hardware Using the Setup Wizard Wizard DWL-AG132 Install Guide DWL-AG700AP The Found New Hardware Wizard After connecting the DWL-AG132, the Found New Hardware Wizard (Windows XP) screen will appear: Select Install the software automatically (Recommended). Click Next Click Continue Anyway. D-Link Systems, Inc.
The Found New Hardware Wizard DWL-AG132 DWL-AG132 Install Guide Select Install the software automatically (Recommended). Click Next Click Continue Anyway. D-Link AirPremier AG DWL-AG132 USB Adapter Click Finish to complete the installation. 7 D-Link Systems, Inc.
Your Installation is Complete! DWL-AG132 DWL-AG132 Install Guide Your Installation is Complete! After completing the Found New Hardware Wizard, the D-Link AirPremier AG DWL-AG132 Configuration Utility will automatically start and the utility icon will appear in the bottom right hand corner of the desktop screen (system tray).
DWL-AG132 Install Guide Appendix A Using the Utility in Windows XP For Windows XP, if you wish to use the AirPremier AG utility, please do the following: Click the XP networking icon to use the Zero Configuration Wireless Click Advanced. Uncheck Use Windows to configure my wireless network settings. Click OK. 9 D-Link Systems, Inc.
DWL-AG132 Install Guide Appendix B Using the AirPremier AG Utility Status: Displays the MAC Address of the access point that is associated with the DWL-AG132. SSID: Displays the Service Set Indentifier assigned to the wireless network. Frequency: Displays the current frequency used by the adapter. Wireless Mode: Displays the wireless mode. The default is Infrastructure. Encryption: Displays whether Encryption is enabled or disabled. Connection Info: Displays the adapter’s connectivity to the network.
Appendix DWL-AG132 B Install Guide DWL-AG132 Install Appendix GuideB Using the AirPremier AG Utility - Link Info (continued) Channel: Displays the channel information. By default, the channel is set to 6 and selection is automatically determined by the DWL-AG132. Signal Strength: Represents the wireless signal between the access point and the DWL-AG132. The percentage coincides with the graphical bar. Packet Count: Graphically displays the statistics of data transmitted and received.
DWL-AG132 Install Guide Appendix B Using the AirPremier AG Utility Configuration SSID: The Service Set Identifier is the name assigned to the wireless network. The factory SSID setting is set to default. Make changes here to match the SSID on existing wireless router or access point. Wireless Mode: The factory setting is set to Infrastructure. Ad-Hoc mode is used for peer-to-peer networking. Data Encryption: The default setting is set to Disabled.
Appendix DWL-AG132 B Install Guide DWL-AG132 Install Appendix GuideB Using the AirPremier AG Utility Configuration (continued) Key Length: When encryption is enabled, you will have the option to specify the level and key format of the encryption used. Select the appropriate Key Index: 1-4, and enter ASCII or hexadecimal digits in the appropriate field. IEEE 802.1x: When encryption is enabled, you will have the option to specify if you wish to use 802.1x authentication. 13 D-Link Systems, Inc.
DWL-AG132 Install Guide Appendix C IP Address Configuration To connect to a network, make sure the proper network settings are configured for the DWL-AG132. For MICROSOFT WINDOWS XP: Go to Start > right-click on My Network Places > select Properties > doubleclick on the network connection associated with the DWL-AG132. Click Internet Protocol (TCP/IP) Click Properties Dynamic IP address setup Used when a DHCP server is available on the local network. (e.g., a Router).
Appendix DWL-AG132 C Install Guide DWL-AG132 Install Appendix GuideC IP Address Configuration (continued) Static IP address setup Used when a DHCP server is not available on the local network. Select Use the following IP address IP address: 192.168.0.28 Subnet Mask: 255.255.255.0 Input a static IP address in the same range as the wireless router or access point.
DWL-AG132 Install Guide Appendix C IP Address Configuration (continued) Dynamic IP address setup Used when a DHCP server is available on the local network. (e.g., a Router). Select Obtain an IP address automatically (if the wireless router or access point has DHCP server enabled). Select Obtain DNS server address automatically. Click OK Static IP address setup Used when a DHCP server is not available on the local network. Select Use the following IP address IP address: 192.168.0.28 Subnet Mask: 255.
DWL-AG132 Install Guide Contacting Technical Support Technical Support D-Link’s website contains the latest user documentation and software updates for D-Link products. D-Link provides free technical support for customers within the United States and Canada for the duration of the product’s warranty period. U.S. and Canadian customers can contact D-Link Technical Support through our website or by phone. United States Telephone (877) 453-5465 Twenty four hours a day, seven days a week.
DWL-AG700AP Install Guide Notes Notes DWL-AG132 Install Guide Notes D-Link Systems, Inc.
DWL-AG700AP Install Guide Notes D-Link Systems, Inc.
DWL-AG700AP Install Guide Your Setup is Complete ! DWL-AG700AP Install Guide Notes Notes 20 D-Link Systems, Inc.
