Table of Contents D-Link DXS-1210 Series User Manual Table of Contents Table of Contents ............................................................................................................................................. i About This Guide ............................................................................................................................................. 1 Terms/Usage ........................................................................................................
Table of Contents D-Link DXS-1210 Series User Manual Configuration Upgrade & Backup > Configuration Backup to HTTP ....................................................... 15 Configuration Upgrade & Backup > Configuration Backup to TFTP ........................................................ 15 Log Backup > Log Backup to HTTP ......................................................................................................... 15 Log Backup >Log Backup to TFTP ..........................................
Table of Contents D-Link DXS-1210 Series User Manual L2 Features > STP > MST Configuration Identification............................................................................ 41 L2 Features > STP > STP Instance ......................................................................................................... 42 L2 Features > STP > MSTP Port Information .......................................................................................... 42 L2 Features > Loopback Detection ..............
Table of Contents D-Link DXS-1210 Series User Manual Security > Trusted Host ............................................................................................................................ 91 Security > Traffic Segmentation Settings ................................................................................................. 92 Security > Storm Control Settings ............................................................................................................
About This Guide D-Link DXS-1210 Series User Manual About This Guide This guide provides installation and instructions for the D-Link 10 Gigabit Ethernet L2 Switch (DXS-121012TC/12SC/10TS), Note: The model you have purchased may appear slightly different from the illustrations shown in the document. Refer to the Product Instruction and Technical Specification sections for detailed information about your switch, its components, network connections, and technical specifications.
1 Product Introduction 1 D-Link DXS-1210 Series User Manual Product Introduction Thank you and congratulations on your purchase of D-Link DXS-1210 Series Switch. D-Link's latest generation L2 10 Gigabit Ethernet switch series blends plug-and-play simplicity with exceptional value and reliability for small and medium-sized business (SMB) networking.
1 Product Introduction D-Link DXS-1210 Series User Manual Front Panel Figure 1.1 – DXS-1210-10TS Front Panel Power LED : The Power LED lights up when the Switch is connected to a power source. Fan error: The Fan error LED lights up when the fan has runtime failure and is brought offline. Reset: By pressing the Reset button, the Switch will change back to the default configuration and all changes will be lost.
1 Product Introduction D-Link DXS-1210 Series User Manual Rear Panel Figure 1.4 – DXS-1210-12TC Rear Panel Power: Connect the AC power cord to this port. DXS-1210-12SC 10-Port 10G SFP+ fiber port and 2-port 10GBASE-T/SFP + combo port L2 10 Gigabit Ethernet Switch. Front Panel Figure 1.5 – DXS-1210-12SC Front Panel Power LED : The Power LED lights up when the Switch is connected to a power source. Fan error: The Fan error LED lights up when the fan has runtime failure and is brought offline.
2 Hardware Installation 2 D-Link DXS-1210 Series User Manual Hardware Installation This chapter provides unpacking and installation information for the D-Link DXS-1210 Series Switch. Safety Cautions To reduce the risk of bodily injury, electrical shock, fire,and damage to the equipment, observe the following precautions: • Observe and follow service markings. • Do not service any product except as explained in your system documentation.
2 Hardware Installation D-Link DXS-1210 Series User Manual • When connecting or disconnecting power to hot-pluggable power supplies, if offered with your system, observe the following guidelines: • Install the power supply before connecting the power cable to the power supply. • Unplug the power cable before removing the power supply. • If the system has multiple sources of power, disconnect power from the system by unplugging all power cables from the power supplies.
2 Hardware Installation D-Link DXS-1210 Series User Manual Then, use the screws provided with the equipment rack to mount the switch in the rack. Figure 2.3 – Mount the Switch in the rack or chassis Step 3 – Plugging in the AC Power Cord Users may now connect the AC power cord into the rear of the switch and to an electrical outlet (preferably one that is grounded and surge protected). Figure 2.
3 Getting Started 3 D-Link DXS-1210 Series User Manual Getting Started This chapter introduces the management interface of D-Link DXS-1210 Series Switch. Management Options The D-Link DXS-1210 Series. Switch can be managed through any port by using the Web-based Management, or through any PC using CLI commands. Each switch must be assigned its own IP Address, which is used for communication with the Web-Based Management or a SNMP network manager.
3 Getting Started D-Link DXS-1210 Series User Manual Figure 3.2 –Enter the IP address 10.90.90.90 in the web browser NOTE: The switch's factory default IP address is 10.90.90.90 with a subnet mask of 255.0.0.0 and a default gateway of 0.0.0.0. When the following login dialog box appears, enter the password and choose the language of the Webbased Management interface then click OK.
4 Configuration 4 D-Link DXS-1210 Series User Manual Configuration The features and functions of the D-Link DXS-1210 Series Switch can be configured for optimum use through the Web-based Management Utility. Smart Wizard Configuration After a successful login, the Smart Wizard will guide you through essential settings of the D-Link DXS-1210 Series Switch. If you do not plan to change anything, click Exit to leave the Wizard and enter the Web Interface.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.2 – SNMP Settings in Smart Wizard User Accounts Settings The User Accounts Settings page allows you to quickly specify the user account function. Enter the User Name, Privilege, Password Type and Password. Click Apply & Save to save the configuration. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.4 – Web-based Management The above image is the Web-based Management screen. The three main areas are the Tool Bar on top, the Function Tree, and the Main Configuration Screen. The Tool Bar provides a quick and convenient way for essential utility functions like firmware and configuration management. By choosing different functions in the Function Tree, you can change all the settings in the Main Configuration Screen.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.6 – Save Configuration Destination: Select the configuration destination to be saved. Startup-config: Check the box to enable the startup configuration function. Click the Apply button to save your settings. Tool Bar > Tool Menu The Tool Menu offers global function controls such as Reset, Reboot Device, Configuration Backup and Restore, Firmware Backup and Upgrade. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Note: The Switch will reboot after restoring, and all current configurations will be lost Firmware Upgrade & Backup > Firmware Upgrade from TFTP Upgrade firmware by using TFTP. Enter the TFTP IP address, source URL, and select a Destination URL. Click Upgrade. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.15 – Tool Menu > Configuration Upgrade & Backup > Configuration Restore from TFTP Configuration Upgrade & Backup > Configuration Backup to HTTP To save the current configuration to a file, click Backup. Figure 4.16 – Tool Menu > Configuration Upgrade & Backup > Configuration Backup to HTTP Configuration Upgrade & Backup > Configuration Backup to TFTP To save the current configuration to a file using TFTP, click Backup. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Ping To ping a computer or device, enter either Target IPv4 or IPv6 Address, Ping Times and Timeout. Enter the required information, Tick the Infinite option, to disable the Ping Times feature and click Apply. The results will be displayed in the Result box. Figure 4.20 – Ping Reset Select which reset option you want to perform and click Apply. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Function Tree All configuration options on the switch are accessed through the Setup menu on the left side of the screen. Click on the setup item that you want to configure. The following sections provide more detailed description of each feature and function. Figure 4.25 –Function Tree Device Information The Device Information provides an overview of the switch, including essential information such as firmware & hardware information, and IP settings.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.27 – System > System Information System > Port Configuration > Port Settings In the Port Settings page, the status of all ports can be monitored and adjusted for optimum configuration. Figure 4.28 – System > Port Configuration > Port Settings From Port / To Port: Select the appropriate port range to be configured. State: Enable or disable the physical port.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.29 – System > Port Configuration > Port Status System > Port Configuration > Error Disable Settings The Error Disable Settings page allows you to configure the sending of SNMP notifications for error disable state. Figure 4.30 – System > Port Configuration > Error Disable Settings Error Disable Trap Settings: Asserted: Select to enable or disable the notifications when entering into the error disabled state.
4 Configuration D-Link DXS-1210 Series User Manual System > Port Configuration > Jumbo Frame The Jumbo Frame page allows you to view and configure the Jumbo Frame size and settings. Jumbo frames are Ethernet frames with more than 1,518 bytes of payload. The Switch supports jumbo frames with a maximum frame size of up to 9216 bytes. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.33 – System > System Log > System Log Server Settings IP Address: Select and enter the IPv4 address or IPv6 Address. UDP Port (514 or 1024-65535): Enter the system log server’s UDP port number. This value must be 514 or between 1024 and 65535. The default value is 514. Severity: Select the severity value of the type of information that will be logged.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.36 – System > Time and SNTP > Time Zone Settings Summer Time State: Select Summer Time State setting. Options to choose from are Disabled, Recurring Setting, and Date Setting. Time Zone Offset: Select the local time zone’s offset from Coordinated Universal Time (UTC). The Recurring Setting can be configured below: From:Week of the Month – Select week of the month that daylight saving time will start.
4 Configuration D-Link DXS-1210 Series User Manual System > Time and SNTP > SNTP Settings The SNTP Settings page allows you to configure the time settings for the Switch. Figure 4.37 – System > Time and SNTP > SNTP Settings SNTP Global Settings: SNTP State: Select to enable or disable the SNTP state. Poll Interval (30-99999): Enter the poll interval. The value is from 30 to 99999 seconds. The default interval is 720 seconds. Click the Apply button to save your settings.
4 Configuration D-Link DXS-1210 Series User Manual Management > User Accounts Settings The User Accounts Settings page allows you to create and configure user accounts. Active user account sessions can be viewed. By default, there is no user account created on the Switch. The pre-defined user account privilege levels supported by this switch are: • Basic User – Privilege Level1. This user account level has the lowest priority of the user accounts.
4 Configuration D-Link DXS-1210 Series User Manual Management > SNMP > SNMP Global Settings Simple Network Management Protocol (SNMP) is an OSI Layer 7 (Application Layer) protocol designed specifically for managing and monitoring network devices. SNMP enables network management stations to read and modify the settings of gateways, routers, switches, and other network devices.
4 Configuration D-Link DXS-1210 Series User Manual Management > SNMP > SNMP View Table Settings The SNMP View page allows you to maintain SNMP views to community strings that define the MIB objects which can be accessed by a remote SNMP manager. Figure 4.43 – Management > SNMP > SNMP View Table Settings View Name: Create a name of the view, up to 32 characters. Subtree OID: The Object Identifier (OID) Subtree for the view.
4 Configuration D-Link DXS-1210 Series User Manual string to access to the SNMP agent. Click Add to a new entry based on the information entered or Delete to remove the specified entry. Management > SNMP > SNMP Group Table Settings The SNMP Group page allows you to assign SNMP Users into SNMP Groups. SNMPv3 can control access and security policies on a per group basis. Figure 4.45 – Management > SNMP > SNMP Group Table Settings Group Name: Enter the SNMP user group of up to 32 characters.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.46 – Management > SNMP > SNMP Engine ID Local Settings Management > SNMP > SNMP User Table Settings The SNMP User Table Settings page allows you to maintain the SNMP user table for the use of SNMPv3. SNMPv3 allows or restricts users using the MIB OID, and encrypts the SNMP messages sent out between users and Switch. Figure 4.47 – Management > SNMP > SNMP User Table Settings User Name: Enter a SNMP user name of up to 32 characters.
4 Configuration D-Link DXS-1210 Series User Manual Click Add to create a new SNMP user account or click Delete to remove any existing data. Management > SNMP > SNMP Host Table Settings The SNMP Host Table Settings page allows you to configure the SNMP trap recipients. Figure 4.48 – Management > SNMP > SNMP Host Table Settings Host IPv4/IPv6 Address: Select IPv4 or IPv6 and specify the IP address of SNMP management host.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.50 – Management > RMON > RMON Statistics Settings The RMON Ethernet Statistics Configuration contains the following fields: Port: Select the port from which the RMON information was taken. Index (1 - 65535): Indicates the RMON Ethernet Statistics entry number. Owner: Displays the RMON station or user that requested the RMON information. Click Add to activate your entry or click to renew the details collected and displayed.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.52 – Management > RMON > RMON Alarm Settings The configuration contains the following fields: Index (1 - 65535): Enter a specific alarm. Variable: Select the selected MIB variable value. Rising Threshold (0 ~ 2^31-1): Displays the rising counter value that triggers the rising threshold alarm. Rising Event Index (1 ~ 65535): Displays the event that triggers the specific alarm. The possible field values are user defined RMON events.
4 Configuration D-Link DXS-1210 Series User Manual Type: Select the event type. The possible values are: None – Indicates that no event occurred. Log – Indicates that the event is a log entry. SNMP Trap – Indicates that the event is a trap. Log and Trap – Indicates that the event is both a log entry and a trap. Community: Enter the community to which the event belongs. Owner: Enter the time that the event occurred. Click Add to add a new RMON event.
4 Configuration D-Link DXS-1210 Series User Manual Management > D-Link Discover Protocol Settings The D-Link Discover Protocol Settings page allows you to configure and display D-Link Discovery Protocol (DDP). Figure 4.56 – Management > D-Link Discover Protocol Settings D-Link Discovery Protocol State: Enter the enable or disable the D-Link Discovery Protocol state. Report Timer: Specify the interval in seconds between two consecutive DDP report messages.
4 Configuration D-Link DXS-1210 Series User Manual Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. L2 Features > FDB > Static FDB > Multicast Static FDB The Multicast Static FDB page allows you to view and configure the static multicast forwarding settings on the Switch. Figure 4.58 – L2 Features > FDB > Static FDB > Multicast Static FDB From Port / To Port: Enter the appropriate port range used for the configuration.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.60 – L2 Features > FDB > MAC Address Table Settings – MAC Address Learning From Port / To Port: Enter the range of ports that will be used for this configuration. State: Select to enable or disable the MAC address learning function on the specified ports. Click the Apply button to save your settings. L2 Features > FDB > MAC Address Table The MAC Address Table page allows you to view the entries listed in the MAC address table. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.62 – L2 Features > 802.1Q VLAN 802.1Q VLAN: VID List: Enter the VLAN ID list that will be created. Click the Apply button to save your settings. Click the Delete button to remove the specific entry. Find VLAN: VID (1-4094): Enter the VLAN ID to be displayed. Click the Find button to locate a specific entry based on the information entered. Click the View All button to locate all the entries.
4 Configuration D-Link DXS-1210 Series User Manual After clicking the VLAN Detail button, the following page will appear: Figure 4.65 – L2 Features > VLAN Interface – VLAN Detail After clicking the Edit button, the following window will appear. This is a dynamic window that will change when a different VLAN Mode is selected. When Access was selected as the VLAN Mode, the following page will appear. Figure 4.66 – L2 Features > VLAN Interface – VLAN Detail Port: Display the VLAN port number.
4 Configuration D-Link DXS-1210 Series User Manual each link between bridges is sensitive to the status of the link. Ultimately this difference results in faster detection of failed links, and thus faster topology adjustment. By default Multiple Spanning Tree is enabled. It will tag BPDU packets to receiving devices and distinguish spanning tree instances, spanning tree regions and the VLANs associated with them. After enabling STP, configure the STP Global Settings. (shown below) Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Each switch on the hop count will reduce the hop count by one until the value reaches zero. The Switch will then discard the BDPU packet and the information held for the port will age out. Bridge Hello Time (0-2): After selecting RSTP/STP as the STP Mode, this parameter will be available. Enter the bridge’s hello time value here. This value must be between 1 and 2 seconds. By default, this value is 2 seconds.
4 Configuration D-Link DXS-1210 Series User Manual considered to have a Shared connection .The port cannot transit into the forwarding state rapidly by setting the link type to Shared. By default this option is Auto. Port Fast: Select the port fast option. The options to choose from are Network, Disabled, and Edge. In the Network mode the port will remain in the non-port-fast state for three seconds. The port will change to the port-fast state if no BPDU is received and changes to the forwarding state.
4 Configuration D-Link DXS-1210 Series User Manual Instance ID Settings: Instance ID (1 - 64): Enter the MSTI ID associated with the VID List. The possible field range is 1-64. Action: The possible values are: Add VID - Indicates that the edit type is add. Remove VID - Indicates that the edit type is removed. VID List: Enter the VID range from configured VLANs set on the Switch. Click Apply button to save your settings. Click Edit to modify the setting of VID or click Delete to remove it.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.72 – L2 Features > Loopback Detection Settings Loopback Detection State: Enable or disable loopback detection. The default is disabled. Mode: Select either Port-based or VLAN-based. Enabled VLAN ID List: Enter the VLAN ID for loop detection. This only takes effect when the VLAN-based is selected in the Mode drop-down list. Interval (1-32767): Set a Loop Detection Interval between 1 and 32767 seconds. The default is 2 seconds.
4 Configuration D-Link DXS-1210 Series User Manual Destination IP. By default, this option is Source MAC. System ID: The System ID information. Click the Apply button to save your settings. Channel Group Information: From Port / To Port: Select the appropriate port range used for the configuration. Group ID: Enter the channel group number. This value must be between 1 and 32. The system will automatically create the port-channel when a physical port first joins a channel group.
4 Configuration D-Link DXS-1210 Series User Manual Click the Edit button to re-configure the specific entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. After clicking the Show Detail button, the following window will appear: Figure 4.75 – L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping – Show Detail Click the Modify button to edit the information in the following window: Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Robustness Value (1-7): Enter the robustness variable used in IGMP snooping. Last Member Query Interval (1-25): Enter the interval at which the IGMP snooping querier sends IGMP group-specific or group-source-specific query messages. Click the Apply button to save your settings.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.78 – L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Mrouter Settings VID (1-4094): Enter the VLAN ID and the range is between 1 and 4094. Configuration: Select the port configuration type. Port: Select to have the configured ports to be static multicast router ports. Forbidden Port – Select to have the configured ports not to be multicast router ports. From Port / To Port: Select the range of ports to be configured.
4 Configuration D-Link DXS-1210 Series User Manual Click the Find button to locate a specific entry based on the information entered. Click the Find All button to view all the entries. L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Setting The MLD Snooping Settings page allows you to configure the MLD snooping settings. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.81 – L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Setting – Show Detail The window displays the detail information about MLD snooping VLAN. Click the Modify button to edit the information in the following window. After clicking the Edit button in MLD Snooping Settings window, the following window will appear. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Click the Apply button to save your settings. L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Groups Setting The MLD Snooping Groups Settings page allows you to configure and view the MLD snooping static group, and view MLD snooping group. Figure 4.83 – L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Group Setting VID (1-4094): Enter the VLAN ID. Group Address: Enter the IP multicast group address.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.84 – L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Mrouter Settings VID (1-4094): Enter the VLAN ID. Configuration: Select the port configuration. Available options are Port and Forbidden Port. Port: Select to have the configured ports as being connected to multicast-enabled routers. Forbidden Port: Select to have the configured ports as being not connected to multicast-enabled routers.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.86 – L2 Features > L2 Multicast Control > Multicast Filtering VID List: Enter the VLAN ID. Multicast Filter Mode: Select the multicast filter mode. Options to choose from are Forward Unregistered, Forward All, and Filter Unregistered. When selecting the Forward Unregistered option, registered multicast packets will be forwarded based on the forwarding table and all unregistered multicast packets will be flooded based on the VLAN domain.
4 Configuration D-Link DXS-1210 Series User Manual through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table. Click Apply to make the change effective. LLDP Forward State: Select to enable or disable LLDP forward state. When the LLDP State is disabled and LLDP Forward Sate is enabled, the received LLDPDU packet will be forwarded. LLDP Trap State: Select to enable or disable the LLDP trap state.
4 Configuration D-Link DXS-1210 Series User Manual and IPv6. Action: Select to remove or add the action field. Address: Enter the IP address to be sent. Click Apply to accept the changes made. L2 Features > LLDP > LLDP Management Address List The LLDP Management Address List page displays the detailed management address information for the entry. Figure 4.89 – L2 Features > LLDP >LLDP Management Address List Management Address: Select IPv4, IPv6 or All address to be displayed.
4 Configuration D-Link DXS-1210 Series User Manual L2 Features > LLDP > LLDP Dot1 TLVs Settings This LLDP Dot1 TLVs Settings page allows you to configure an individual port or group of ports to exclude one or more of the IEEE 802.1 organizational port VLAN ID TLV data types from outbound LLDP advertisements. Figure 4.91 – L2 Features > LLDP > LLDP Dot1 TLVs Settings From Port / To Port: A consecutive group of ports may be configured starting with the selected port.
4 Configuration D-Link DXS-1210 Series User Manual MAC/PHY Configuration/Status: Select whether the MAC/PHY Configuration Status is enabled on the port. The possible field values are: Enabled – Enables the MAC/PHY Configuration Status on the port. Disabled – Disables the MAC/PHY Configuration Status on the port. Link Aggregation: Specifies whether the link aggregation is enabled on the port. The possible field values are: Enabled – Enables the link aggregation configured on the port.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.94 – L2 Features > LLDP > LLDP Statistics Information The following information can be viewed: LLDP Statistics Information: Displays the counters that refer to the whole switch. Last Change Time – Displays the time for when the last change entry was last deleted or added. It is also displays the time elapsed since last change was detected. Total Inserts – Displays the number of new entries inserted since switch reboot.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.95 – L2 Features > LLDP > LLDP Local Port Information Port: Displays the port number. Port ID Subtype: Displays the port ID subtype. Port ID: Displays the port ID (Unit number/Port number). Port Description: Displays the port description. Click Find to displays more information for the specified port. After clicking the Show Detail button, the following page will appear. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Click the Clear button to remove the specified port of LLDP neighbor port or click Clear All button to remove all LLDP neighbor ports. L3 Features > ARP > ARP Aging Time The ARP Aging Time page allows you to view and configure the ARP aging time settings. Figure 4.98 – L3 Features > ARP > ARP Aging Time Timeout(min): Specifies the aging time of the ARP entry. The default is 5 minutes. Click the Apply button to save your settings.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.100 – L3 Features > ARP > ARP Table Interface VLAN (1-4094): Select and enter the interface’s VLAN ID. IP address: Select and enter the IP address to be displayed. Mask: Enter the mask address for the specified IP address. Hardware Address: Select and enter the MAC address. Type: Select the type. Click the Find button to locate a specific entry based on the information entered. Click the Delete button to remove the specific entry.
4 Configuration D-Link DXS-1210 Series User Manual Click the Back button to return to the previous window. State: Select to enable or disable the IPv4 interface’s global state. Click the Apply button to save your settings. IP Settings: Get IP From: Select the IP from option. The values are Static and DHCP. When the Static option is selected, users can enter the IPv4 address of this interface manually in the fields provided.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.105 – L3 Features > IPv6 Interface Interface VLAN (1-4094): Enter the VLAN ID of IP interface. Click Apply for the settings to take effect. Click the Find button to display the specific entry. Click the Detail button to view and configure more detailed settings for the IPv6 interface entry. After clicking the Detail button, the following window will be appear. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.108 – L3 Features > IPv6 Interface – DHCPv6 Client Click the Restart button to restart the DHCPv6 client. Client State: Select to enable or disable the DHCPv6 client state. Click the Apply button to save your settings. L3 Features > IPv6 Neighbor The user can configure the Switch’s IPv6 neighbor settings. The Switch’s current IPv6 neighbor settings will be displayed in the table at the bottom of this window. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.111 – QoS > Port Default CoS From Port / To Port: Select the range of ports to be configured. Default CoS: Select the default CoS option for the specified ports. The values are from 0 to 7. Click the Override check box to apply the port's default CoS to all packets (tagged or untagged) received by the port. Select the None option to use the default settings. Click the Apply button to save your settings.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.113 – QoS > Queue Settings From Port / To Port: Select the range of ports to be configured. Queue ID: Select the queue id value. The range is between 0 and 7. WRR Weight (0-127): Enter the WRR weight value. The value is between 0 and 127. WDRR Quantum (0-127): Enter the WRR quantum value. The value is between 0 and 127. Click the Apply button to save your settings.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.115 – QoS > Port Rate Limiting From Port / To Port: Select the range of ports to be configured. Direction: Select the direction. Available options are Input and Output. When Input is selected, the rate limit for ingress packets is configured. When Output is selected, the rate limit for egress packets is configured. Rate Limit: Enter the Rate Limit for the specified port.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.116 – QoS > Queue Rate Limiting From Port / To Port: Select the range of ports to be configured. Queue ID: Select the queue ID for the specified ports. The value is between 0 and 7. Rate Limit: Specify the Rate limit option. If you selected the Min Bandwidth option, enter the minimum bandwidth rate limit value in the space provided. This value must be between 8 and 10000000 kbps.
4 Configuration D-Link DXS-1210 Series User Manual QoS > DSCP CoS Mapping The DSCP CoS Mapping page allows you to view and configure the DSCP CoS mapping settings. Figure 4.118 – QoS > DSCP CoS Mapping From Port / To Port: Select the range of ports to be configured. CoS: Select the CoS priority. DSCP List (0-63): Enter the DSCP list number. Click the Apply button to save your settings.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.120 – ACL > ACL Configuration Wizard – Packet Type MAC: Select to create a MAC ACL. IPv4: Select to create an IPv4 ACL. IPv6: Select to create an IPv6 ACL. Click the Back button to return to the previous window. Click the Next button to continue. To define the MAC ACL: Select MAC and then click the Next button. Click the associated tabs with MAC Address, Ethernet Type and 802.1Q VLAN, the following page will appear: Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Ethernet Type (0x600-0xFFFF): Enter the Ethernet type hexadecimal value. The value is between 0x600 and 0xFFFF. When any Ethernet type profile is selected in the Specify Ethernet Type drop-down list, the appropriate hexadecimal value will automatically be entered. Ethernet Type Mask (0x0-0xFFFF): Enter the Ethernet type mask hexadecimal value. The value is between 0x0 and 0xFFFF.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.123 – ACL > ACL Configuration Wizard – Create IPv4 ACL-TCP Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. Source Port: Select the source port value. Destination Port: Select the destination port value. IP Precedence: Select the IP precedence value.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.124 – ACL > ACL Configuration Wizard – Create IPv4 ACL-UDP Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. Source Port: Select the source port value. Destination Port: Select the destination port value. IP Precedence: Select the IP precedence value.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.125 – ACL > ACL Configuration Wizard – Create IPv4 ACL-ICMP Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. IP Precedence: Select the IP precedence value. Options to choose from are 0 (routine), 1 (priority), 2, (immediate), 3 (flash), 4 (flash-override), 5 (critical), 6 (internet), and 7 (network).
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.126 – ACL > ACL Configuration Wizard – Create IPv4 ACL-EIGRP Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. Fragments: Specify the Fragments option to include packet fragment filtering. Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP.
4 Configuration D-Link DXS-1210 Series User Manual Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. IP Precedence: Select the IP precedence value. Options to choose from are 0 (routine), 1 (priority), 2, (immediate), 3 (flash), 4 (flash-override), 5 (critical), 6 (internet), and 7 (network). ToS: Select the Type-of-Service (ToS) value that will be used.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.129 – ACL > ACL Configuration Wizard – Create IPv4 ACL-IGMP Fragments: Select the Fragments option to include packet fragment filtering. Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. IP Precedence: Select the IP precedence value.
4 Configuration D-Link DXS-1210 Series User Manual Fragments: Select the Fragments option to include packet fragment filtering. Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. IP Precedence: Select the IP precedence value. Options to choose from are 0 (routine), 1 (priority), 2, (immediate), 3 (flash), 4 (flash-override), 5 (critical), 6 (internet), and 7 (network).
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.132 – ACL > ACL Configuration Wizard – Create IPv4 ACL-VRRP Fragments: Select the Fragments option to include packet fragment filtering. Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. IP Precedence: Select the IP precedence value.
4 Configuration D-Link DXS-1210 Series User Manual Fragments: Select the Fragments option to include packet fragment filtering. Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. IP Precedence: Select the IP precedence value. Options to choose from are 0 (routine), 1 (priority), 2, (immediate), 3 (flash), 4 (flash-override), 5 (critical), 6 (internet), and 7 (network).
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.135 – ACL > ACL Configuration Wizard – Create IPv4 ACL-Protocol ID Fragments: Select the Fragments option to include packet fragment filtering. Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. IP Precedence: Select the IP precedence value used.
4 Configuration D-Link DXS-1210 Series User Manual Fragments: Select the Fragments option to include packet fragment filtering. Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. IP Precedence: Select the IP precedence value. Options to choose from are 0 (routine), 1 (priority), 2, (immediate), 3 (flash), 4 (flash-override), 5 (critical), 6 (internet), and 7 (network).
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.138 – ACL > ACL Configuration Wizard – Create IPv6 ACL-UDP Source Port: Select the source port value. Destination Port: Select the destination port value. Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. DSCP (0-63): Select the DSCP value. And the range is between 0 and 63. Flow Label (0-1048575): Enter the flow label value.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.139– ACL > ACL Configuration Wizard – Create IPv6 ACL-ICMP Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. DSCP (0-63): Select the DSCP value. And the range is between 0 and 63. Flow Label (0-1048575): Enter the flow label value. This value must be between 0 and 1048575. Specify ICMP Message Type: Select the ICMP message type used.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.140 – ACL > ACL Configuration Wizard – Create IPv6 ACL-Protocol ID Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. DSCP (0-63): Enter the DSCP value. And the range is between 0 and 63. Flow Label (0-1048575): Enter the flow label value. This value must be between 0 and 1048575. Action: Select the action for the rule.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.142 – ACL > ACL Configuration Wizard – Create IPv6 ACL-PCP Source: Select the source information. The values are Any, Host and IP. Destination: Select the destination information. The values are Any, Host and IP. DSCP (0-63): Enter the DSCP value. And the range is between 0 and 63. Flow Label (0-1048575): Enter the flow label value. This value must be between 0 and 1048575. Time Range: Enter the time range.
4 Configuration D-Link DXS-1210 Series User Manual DSCP (0-63): Enter the DSCP value. And the range is between 0 and 63. Flow Label (0-1048575): Enter the flow label value. This value must be between 0 and 1048575. Action: Select the action for the rule. The values are Permit and Deny. After selecting the None option as the Protocol Type then click the associated tabs with IPv6 Address, IPv6 DSCP and Flow Label, the following page will appear: Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual ACL > ACL Access List The ACL Access List page allows you to view and configure the ACL access list settings. Figure 4.146 – ACL > ACL Access List ACL Type: Select the ACL profile type to find. Options to choose from are All, IP ACL, IPv6 ACL, MAC ACL, and Expert ACL. ID (1-14999): Select and enter ACL ID. The range is between 1 and 14999. ACL Name: Select and enter ACL name. The name can be up to 32 characters long.
4 Configuration D-Link DXS-1210 Series User Manual After clicking the Please Select button, the following page will appear. Figure 4.148 – ACL > ACL Interface Access Group - Select Security > Port Security > Port Security Global Settings The Port Security Global Settings page allows you to view and configure the port security global settings.
4 Configuration D-Link DXS-1210 Series User Manual Security > Port Security > Port Security Port Settings The Port Security Port Settings page allows you to view and configure the port security port settings of the Switch. Figure 4.150 – Security > Port Security > Port Security Port Settings From Port / To Port: Select the range of ports to be configured. State: Select to enable or disable the port security state of specified ports.
4 Configuration D-Link DXS-1210 Series User Manual VID (1-4094): Enter the VLAN ID. The range is between 1 and 4094. Click the Add button to add a new entry based on the information entered. Click the Delete button to remove a new entry based on the information entered. Click the Clear by Port button to clear the information based on the port selected. Click the Clear by MAC button to clear the information based on the MAC address entered.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.153 – Security > DHCP Server Screening > DHCP Server Screening Port Settings From Port / To Port: Select the range of ports to be configured. State: Select to enable or disable the DHCP server screening port state. Profile Name: Enter the profile name of specified ports. Server IP: Select IPv4 Address or IPv6 Address and enter the DHCP server IP. Click the Apply button to save your settings.
4 Configuration D-Link DXS-1210 Series User Manual Type: Specify the trusted host type. The options are Telnet, Ping, HTTP and HTTPS. Click the Apply button to save your settings. Security > Traffic Segmentation Settings This feature provides administrators to limit traffic flow from a single port to a group of ports on a single Switch. This method of segmenting the flow of traffic is similar to using VLANs to limit traffic, but is more restrictive. Figure 4.
4 Configuration D-Link DXS-1210 Series User Manual Trap State: Select the storm control trap state. The options are None, Storm Occur, Storm Clear, and Both. When None is selected, no traps will be sent. When Storm Occur is selected, a trap notification will be sent when a storm event is detected. When Storm Clear is selected, a trap notification will be sent when a storm event is cleared. Click the Apply button to save your settings.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.159 – Security > DoS Attack Prevention Settings DoS Attack Prevention Settings: DoS Type Selection: Tick the DoS type option that will be prevented State: Select to enable or disable the DoS attack prevention state. Action: Select the action for the DoS attack. Click the Apply button to save your settings.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.161 – Security > SSL > SSL Service Policy Policy Name: Enter a policy name for SSL. Click the Add button to save your settings. Click the Find button to locate a specific entry based on the information entered. Session Cache Timeout (60-86400): Enter the session cache timeout value. The value is between 60 and 86400 seconds. Cipher Suites: Select the cipher suites that will be associated with this profile.
4 Configuration D-Link DXS-1210 Series User Manual NOTE: Cable length detection is available on Gigabit ports only. NOTE: Please be sure that the Power Saving feature is disabled before enabling the Cable Diagnostics function. Monitoring > Statistics > Port This page allows you to display the packet statistics of ports. Figure 4.163 – Monitoring > Statistics > Port From Port / To Port: Select the range of ports to be configured.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.164 – Monitoring > Statistics > Port – Show Detail Click the Back button to return to the previous window. Click the Refresh button to refresh the display table. Monitoring > Statistics > Port Counters The Port Counters page allows you to display port counter statistics. Figure 4.165 – Monitoring > Statistics > Port Counters From Port / To Port: Select the range of ports to be configured.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.167 – Monitoring > Statistics > Counters From Port / To Port: Select the range of ports to be configured. Click the Find button to locate a specific entry based on the information entered. Click the Refresh button to refresh the display table. Click the Clear button to clear all the information for the specific ports. Click the Clear All button to clear all the information in this table.
4 Configuration D-Link DXS-1210 Series User Manual Figure 4.169 – Monitoring > Mirror Settings Session Number: Select the mirror session number for the entry. Destination: Select the destination port for mirror settings. Source: Select the range of ports to be the source port and Frame Type to be mirrored. Click the Add button to add the newly configured mirror entry based on the information entered. Click the Delete button to delete an existing mirror entry based on the information entered.
4 Configuration D-Link DXS-1210 Series User Manual After clicking the Power Saving Shutdown Settings tab, the following page will appear. Figure 4.171 – Green > Power Saving – Shutdown Settings From Port / To Port: Select the range of ports to be configured. Time Range: Enter the time range to associate with the specified ports. Click the Apply button to save your settings. Green > EEE The Energy Efficient Ethernet (EEE) is defined in IEEE 802.3az.
5 Command Line Interface 5 D-Link DXS-1210 Series User Manual Command Line Interface The D-Link DXS-1210 Series Switch allows a computer or terminal to perform some basic monitoring and configuration tasks by using the Command Line Interface (CLI) via TELNET protocol. To connect a switch via TELNET: 1. Make sure the network connection between the switch and PC is active. 2.
5 Command Line Interface save {startup-config | config-1 | config-2} boot image [image-1 | image-2] debug info debug show tech-support D-Link DXS-1210 Series User Manual Save configuration. Select the boot up image. Displays Debug Table. Displays technical support information. Each command is listed in detail, as follows: ? Purpose To display a list of commands. Syntax ? Description The ? command displays a list of commands of the switch. Parameters None. Restrictions None.
5 Command Line Interface D-Link DXS-1210 Series User Manual information using the traditional format (for example,10.1.2.3/255.0.0.0) dhcp − Allows the selection of the DHCP protocol for the assignment of an IP address to the Switch’s System IP interface. ipv6address − Use this parameter to statically assign an IPv6address to this interface. This address should define a host address and a network prefix length. Multiple IPv6 addresses can be configured for a single IP interface.
5 Command Line Interface D-Link DXS-1210 Series User Manual - The IPv6 address of the host. - Specify the ping packet size. - Specify the time out value. The range is between 1 and 100 seconds. repeat - Specify the repeat time. Restrictions Only Administrator or operator-level users can issue this command Example usage: To ping the IP address 10.90.90.98: DXS-1210-12TC> ping 10.90.90.98 Reply Not Received From : 10.90.90.
5 Command Line Interface Restrictions D-Link DXS-1210 Series User Manual Only Administrator can issue this command. Example usage: To restore all of the Switch’s parameters to their default values: DXS-1210-12TC> reset config This command will clear all of system configuration as factory. System will reboot after clearing. Do you want to continue? (y/n)y DXS-1210-12TC> show ipif Purpose To display the configuration of an IP interface on the Switch.
5 Command Line Interface D-Link DXS-1210 Series User Manual Example usage: To display IPv6 interface settings: DXS-1210-12TC> show ipv6 interface 1 brief vlan1 is up, IPv6 is enabled Link-local address: fe80::ee22:80ff:fe77:2016, Link status is up Total Entries: 1 DXS-1210-12TC> show switch Purpose To display information about the Switch. Syntax show switch Description The show switch command displays the status of the switch. Parameters None. Restrictions None.
5 Command Line Interface D-Link DXS-1210 Series User Manual password. Parameters − The name of the user. privilege - Specify the privilege level. The value 1 is for Basic user, 12 for Operator and 15 for Administrator. password - Specify the password. Restrictions Only Administrator can issue this command.
5 Command Line Interface D-Link DXS-1210 Series User Manual debug info Purpose To display the ARP table and MAC FDB information of the Switch. Syntax debug info Description The debut info command displays the ARP table and MAC FDB of the Switch. Parameters None. Restrictions Only Administrator can issue this command.
5 Command Line Interface D-Link DXS-1210 Series User Manual #--------------------------------------------------------------------# DXS-1210-12TC 10 Gigabit Ethernet Switch # Technical Support Information # # Firmware: V1.00.021 # Copyright(C) 2014 D-Link Corporation. All rights reserved. #--------------------------------------------------------------------******************** Basic System Information ******************** Boot Time : RTC Time :27/04/2011 18:41:32 Boot PROM Version :V1.00.
Appendix A - Technical Specifications D-Link DXS-1210 Series User Manual Appendix A - Technical Specifications - DEM-431XT: 10GBASE-SR 80m - DEM431XT-DD: 10GBASE-SR, 80m - DEM-432XT: 10BASE-LR, 10km - DEM-432XT-DD: 10GBASE-LR, 10km - DEM-433XT: 10GBASE-ER, 40km - DEM-433XT-DD: 10GBASE-ER, 40km - DEM-434XT: 10GBASE-ZR, 80km WDM SFP+ Transceiver: - DEM-436XT-BXU: 10GBASE-LR 20km - DEM-436XT-BXD: 10GBASE-LR 20km CWDM SFP+ Transceiver: - DEM-X10CS-1271: 10G Single-Mode 10KM CWDM SFP+ Transceiver - DEM-X10CS-1
Appendix A - Technical Specifications D-Link DXS-1210 Series User Manual CCC Class A saving figures since main chipsets (both MAC and PHY) are disabled for all ports. Energy Efficient Ethernet (EEE): EEE is disabled by default, user can enable EEE via Web GUI Safety Certifications cUL, CB, CE, CCC, BSMI Features VLAN L2 Features Supports up to 16K MAC address Jumbo frame: Supports up to 9KB IGMP snooping: Supports 128 multicast group MLD Snooping 802.1D Spanning Tree 802.1s MSTP 802.
Appendix A - Technical Specifications D-Link DXS-1210 Series User Manual IP and MAC ACL Broadcast Storm Control D-Link Safeguard Engine DHCP Server Screening over IPv4 or IPv6 : Maximum 5 entries SSL: Support v1/v2/v3 Support DHCP Snooping IP-MAC-Port Binding - Supports ARP packet Inspection as default, ARP and IPv4 packet Inspection as option. - Supports IPv4 DHCP Snooping Management Web-based GUI (IPv6 support) D-Link compact CLI (Supports IPv6 commands) Telnet Server: Max.
