Wireless N HighPower無線寬頻路由器 DIR-619
Table of Contents "# $ % $ & ( )* +, , * ! ! ' - . V 0 # 0 1 ) 2 " 2" ) $ 4 5 / / 3 Configuration Web-based Configuration Utility " 7 1 8 ) " 7 " 9 ) # " : # $ .
Table of Contents Wireless ........................................................... 56 Help ................................................................. 5! Wireless Security ....................................................... 5' What is WEP? ....................................................... 5' Configure WEP ...................................................... 5 What is WPA? .......................................................'Configure WPA/WPA2-PSK ..................................
Section 1-product overview Package Contents • D-Link D-Link DIR-619 DIR-61 wireless wirelessrouter router • power adapter • Ethernet Cable • CD-ROM with User Manual, and warrenty Note: Note:Using Usingaapower powersupply supplywith withaadifferent differentvoltage voltagerating ratingthan thanthe theone oneincluded included with withthe theDIR-619 DIR-618will willcause causedamage damageand andvoid voidthe thewarranty warrantyfor forthis thisproduct. product.
Section 1- roduct Overview Feature • Faster Faster wireless wireless network network -- The he DIR-619 DIR-618 provides provides up up to to 300Mbps* 00Mbps wireless wireless connection connection with with other other 802.11n 802.11n wireless clients. clients.
Section 1- roduct Overview ressing the Reset button restore the router to its original factory default settings power Receptor L ort connect Ethernet device such as computers, switches and hubs D-Link DIR-61 User Manual uto MDI MDI W port is the connection for the Ethernet cable DŽ to the cable or DSL modem 6
Section 1-Product Overview Hardware Overview LEDs INTERNET A solid light indicates connection on the WAN port.This LED blinks during data transmission. Power LED A solid light indicates a proper connection to the power supply. D-Link DIR-619 User Manual WLAN LED A solid light indicates that the wireless function is ready.this LED blinks during wireless data transmission. LAN LED A solid light indicates connection to the Ethernet-enabled computers on ports 1-4.This LED blinks during data transmission.
Section 2-Installation Installation this section will walk you through the installation process. Placement of the router is very important. Please do not put the router in an enclosed area such as closet, cabinet, or in the attic or garage. Before you Begin Please configure the router with the computer that was last connected directly to your modem. Also, you can only use the Ethernet port on your modem.
Section 2-Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business.
Section 2 - Installation Connect to Cable/DSL/Satellite Modem If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below: 1. Place the router in an open and central location. 2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down your computer. 3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the WAN port on the router. 4.
Section 2 - Installation Connect to Another Router If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network: • Disable UPnP™ • Disable DHCP • Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address from your other router. To connect to another router, please follow the steps below: 1.
Section 2 - Installation 6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the WAN port of the D-Link router. 8. You may now use the other three LAN ports to connect other Ethernet devices and computers. To configure your wireless network, open a web browser and enter the IP address you assigned to the router.
Section 3 - Configuration Configuration This section will show you how to configure your new D-Link wireless router using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1). Enter the user name (admin) and your password. Leave the password blank by default.
Section 3-Configuration Configuration Wizard You may run the setup wizard from the opening quick setup window to quickly set up your router. Based on your network condition,router will detect your Internet connetion type . Click Easy Setup, you will be directed to the "Internet configuration updated" window. After the completion of detection, "configure your internet connection" window will pop up. Here take "PPPoE" as an example.
Section 3- Configuration This page dispalys the completed Internet and wireless configuration.Click save to save the configuration. Click config to change the wireless settings. Please wait for rebooting. When the router has finished rebooting, the opening window will be displayed.
Section 3- Configuration Internet Setup You may run the setup wizard from the opening Internet Setup window to quickly set up your router. Click Internet Connection Setup Wizard, you will be directed to the first window of the wizard. Click Next to continue. Create a new password and then click Next to continue.
Section 3-Configuration Select your time zone and NTP-server from the drop-down menu and then click Next to continue. Select No, I want to set by manual Select the type of Internet connection you use and then click Next to continue. If you selected Dynamic, you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click Clone Your PC’s MAC Address and then click Next to continue.
Section 3-Configuration If you selected PPPoE, enter your PPPoE username and password. Click Next to continue.Select Static if your ISP assigned you the IP address,subnet mask,gateway, and DNS server addresses. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. If you selected PPTP, enter your PPTP username and password. Click Next to continue. If you selected L2TP, enter your L2TP username and password.
Section 3-Configuration If you selected Static, enter your network settings supplied by your Internet provider. Click Next to continue. Click Connect to save your settings. Please allow 1-2 minutes for rebooting. When the router has finished rebooting, the opening window will be displayed.
Section 3 - Configuration Internet Setup Static (assigned by ISP) Select Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
Section 3 - Configuration Internet Setup Dynamic To manually set up the Internet connection, click the Manual Internet Connection Setup button on the Router’s opening window. Host The Host Name is optional but may be required by some Name: ISPs. The default host name is the device name of the Router and may be changed. MAC Address: The default MAC Address is set to the WAN’s physical interface MAC address on the Broadband Router.
Section 3 - Configuration Internet Setup PPPoE Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. PPPoE: Select Dynamic (most common) or Static .
Section 3 - Configuration Internet Setup PPTP Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. PPTP: Select Dynamic (most common) or Static. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. IP Address: Enter the IP address (Static PPTP only).
Section 3 - Configuration Internet Setup L2TP Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. L2TP: Select Dynamic (most common) or Static. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. IP Address: Enter the IP address (Static L2TP only).
Section 3 - Configuration Wireless Setup Wireless settings for the router may be configured manually or by using a wizard. To use the wizard, click the Wireless Connection Setup Wizard button and then follow the steps that are described below. To configure the wireless settings manually, click the Manual Wireless Connection Setup button. The parameters for this window are described later in this section.
Section 3 - Configuration Enter a Wireless Security Password in the textbox and then click Next to continue. This window displays a summary of your wireless security settings. Please print this out or record this information in a safe place and then click Save to continue. The Router will save your new settings and reboot. When it is finished after 1-2 minutes, the opening Wireless Setup window is displayed.
Section 3 - Configuration Wi-Fi To implement Wi-Fi protection, or WCN 2.0, tick the Enable Protected checkbox, click either Generate New PIN or Reset PIN to Setup: Default , and then configure the Wi-Fi settings below. Please see the Setting Up Wi-Fi Protection (WCN 2.0 in Windows Vista) section later in this manual for detailed configuration information. Wireless Mode: Select the wireless mode with which the device is running. Enable Check the box to enable the wireless function.
Section 3 - Configuration 1. To enable wireless security on the Router, use the drop-down menu to select the desired option. To enable WEP, select Enable WEP Wireless Security (basic). 2. Next to Authentication, select either Open or Shared Key. Shared Key provides greater security. 3. Select either 64Bit or 128Bit encryption from the drop-down menu next to WEP Encryption. 4. Next to Default Key Type, select WEP Key 1 and enter a WEP key that you create.
Section 3 - Configuration 1. To enable Enable WPA/WPA2 Wireless Security (enhanced). 2. Next to Cipher Type, select TKIP, AES, or AUTO. 3. Next to PSK/EAP, select PSK. 4. N e x t t o N e t w o r k K e y , e n t e r a passphrase. The key is an alpha-numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. Make sure you enter this key exactly the same on all other wireless clients. 5. Click Save Settings to save your settings.
Section 3 - Configuration 1. To enable WPA/WPA2 for a RADIUS server, next to Security Mode, selec or Enable WPA/WPA2 Wireless Security (enhanced). 2. Next to Cipher Type, select TKIP, AES, or Auto. 3. Next to PSK/EAP, select EAP. 4. Next to RADIUS Server enter the IP Address of your RADIUS server. 5. Next to Port, enter the port you are using with your RADIUS server. 1812 is the default port. 6. Next to Shared Secret, enter the security key. 8. Click Save Settings to save your settings.
Section 3 - Configuration LAN Setup This section will allow you to change the local network settings of the router and to configure the DHCP settings. Router IP Enter the IP address of the router. The default Address: IP address is 192.168.0.1. If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the configuration utility. Subnet Mask: Enter the Subnet Mask. The default subnet mask is 255.255.255.0.
Section 3 - Configuration DHCP Server Settings DHCP stands for Dynamic Host Control Protocol. The DIR-618 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-618.
Section 3 - Configuration Time and Date This section will allow you to configure, update, and maintain the correct time on the internal system clock. Time Select the Time Zone from the drop-down Zone: menu. Enable Ticking this checkbox enables Daylight Saving Daylight time. Click Sync. your computer’s time Saving: settings to copy your PC’s time settings. NTP Tick the “Automatically synchronize with Server D-Link’s Internet time server” checkbox and Used: then use the drop-down menu to select an NTP Server.
Section 3 - Configuration Parental Control This feature allows you to create a list of websites that you want to either allow or deny users access. Configure Select Turn Parental Control OFF, Turn Parental Parental Control ON and ALLOW computers access to Control: ONLY these sites, or Turn Parental Control ON and DENY computers access to ONLY these sites. Website URL: Enter the keywords or URLs that you want to block (or allow). Any URL with the keyword in it will be blocked.
Section 3 - Configuration Port Forwarding This will allow you to open a single port or a range of ports. Rule: Check the box to enabled the rule. Name: Enter a name for the rule. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to. Start Port/ Enter the port or ports that you want to open. If End Port: you want to open one port, enter the same port in both boxes.
Section 3 - Configuration Application Rules Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-618. Rule: Check the box to enable the rule. Name: Enter a name for the rule. Trigger Port: This is the port used to trigger the application.
Section 3 - Configuration MAC Filter Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the Network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the Broadband Router.
Section 3- Configuration Traffic control Traffic control can be used to distribute download bandwidth automatically according to the requirements of the users, and the users also can setup manually. Enable Traffic Select this function to control the access bandwidth of Control: computer in LAN. . Automatic Distribute All the computers in LAN will be distributed the bandwidth Bandwidth: equally. key in bandwidth key in the value to setup the upload and download manually: bandwidth manually.
Section 3 - Configuration Firewall & DMZ This section will allow you to set up a DMZ host and to set up firewall rules. If you have a client PC that cannot run Internet applications properly from behind the DIR-618, then you can set the client up for unrestricted Internet access. It allows a computer to be exposed to the Internet. This feature is useful for gaming purposes. Enter the IP address of the internal computer that will be the DMZ host.
Section 3 - Configuration Advanced Wireless This window allows you to change the behavior of the 802.11g wireless radio from the standard settings. Please be aware that any changes to the factory default settings may adversely affect the behavior of your network. Transmit Power: Set the transmit power of the antennas. Beacon interval: Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended.
Section 3 - Configuration Advanced Network This window allows you to change the LAN settings. Please be aware that any changes to the factory default settings may affect the behavior of your network. Enable UPnP: To use the Universal Plug and Play (UPnP ™) feature tick this checkbox. UPNP provides compatibility with networking equipment, software and peripherals. Enable WAN Unchecking the box will not allow the DIR-618 to Ping Respond: respond to Pings.
Section 3 - Configuration Routing This option allows you to define fixed routes to defined destinations. Enable: Tick this checkbox to enable or disable fixed routes to defined destinations. Interface: Use the drop-down menu to choose the WAN or WAN (Physical Port) Interface the IP packet must use to transit out of the Router. Destination: The IP address of the packets that will take this route. Subnet Mask: The subnet of the IP address of the packets that will take this route.
Section 3 - Configuration Device Administration This window will allow you to change the Administrator password. You can also enable Remote Management. Login Name: Enter a new Login Name for the Administrator account. Password: Enter a new password for the Administrator Login Name and then retype the new password in the Confirm Password textbox. The administrator can make changes to the settings. Enale Graphical Need to enter the Graphical Authentication generated by Authentication: the system when log in.
Section 3 - Configuration Save and Restore This window allows you to save your configuration file to a hard drive, load configuration settings from a hard drive, and restore the Router’s factory default settings. Save Settings Use this option to save the current router to Local Hard configuration settings to a file on the hard disk of the Drive: computer you are using. First, click the Save button. You will then see a file dialog, where you can select a location and file name for the settings.
Section 3 - Configuration Firmware Update You can upgrade the firmware of the Router here. Make sure the firmware you want to use is on the local hard drive of the computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site.
Section 3 - Configuration DDNS Setting The router supports DDNS (Dynamic Domain Name Service). The Dynamic DNS service allows a dynamic public IP address to be associated with a static host name in any of the many domains, allowing access to a specified host from various locations on the Internet. This is enabled to allow remote access to a host by clicking a hyperlinked URL in the form “hostname.dyndns.org”.
Section 3 - Configuration System Check This tool is used to verify the physical connectivity on both the LAN and the WAN interfaces. The Ping Test can be used to test the status of the Internet. Virtual Cable VCT is an advanced feature that integrates a Tester (VCT) LAN cable tester on every Ethernet port on the Info: router. Through the graphical user interface (GUI), VCT can be used to remotely diagnose and report cable faults such as opens, shorts, swaps, and impedance mismatch.
Section 3 - Configuration Schedules The Router allows the user the ability to manage schedule rules for various firewall and parental control features on this window. Once you have finished configuring the new schedule rule, click the Save Settings button at the top of the window. Name: Enter a name for the new schedule rule. Day(s): Choose the desired day(s), either All Week or Select Days. If the latter is selected, please use the checkboxes directly below to specify the individual days.
Section 3 - Configuration Log Settings The system log displays chronological event log data specified by the router user. You may also save a simple text file containing the log to your computer. Click the Save button and follow the prompts to save the file. Save Log File: Click on the Save button link on this window to save the log file to your local hard drive. Syslog Server: click the checkbox to save the log in the log server in the LAN side.
Section 3 - Configuration Device Info This window displays the current information for the DIR-618. It will display the LAN, WAN, and Wireless information. If your WAN connection is set up for a Dynamic IP address then a DHCP Release button and a DHCP Renew button will be displayed. Use DHCP Release to disconnect from your ISP and use DHCP Renew to connect to your ISP. If your WAN connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed.
Section 3 - Configuration Log This window allows you to view a log of activities on the Router. This is especially helpful detecting unauthorized network usage. First Page: View the first page of the log. Last Page: View the last page of the log. Previous: View the previous page. Next: View the next page. Clear: Clear the log. Link to Log Click this button to go directly to the Log Settings Settings: window (Maintenance > Log Settings).
Section 3 - Configuration Statistics The window below displays the Traffic Statistics. Here you can view the amount of packets that pass through the DIR-618 on both the WAN and the LAN ports. The traffic counter will reset if the device is rebooted. Active Session The NAPT Active Session table displays a list of all active conversations between WAN computers and LAN computers.
Section 3 - Configuration Wireless The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless client.
Section 3 - Configuration Help Click the desired hyperlink to get more information about how to use the Router.
Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DIR-618 offers the following types of security: • WPA/WPA2 (Auto) • WEP (Wired Equivalent Privacy) What is WEP? WEP stands for Wired Equivalent Privacy. It is based on the IEEE 802.11 standard and uses the RC4 encryption algorithm.
Section 4 - Security Configure WEP It is recommended to enable encryption on your wireless router before you use wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Wireless Setup on the left side. 2.
Section 4 - Security What is WPA? WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The two major improvements over WEP: • Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is based on 802.
Section 4 - Security Configure WPA/WPA2-PSK It is recommended to enable encryption on your wireless Router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Wireless Setup on the left side. 2.
Section 4 - Security Configure WPA/WPA2 (RADIUS) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Wireless Settings on the left side. 2.
Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Section 5 - Connecting to a Wireless Network Configure WEP It is recommended to enable WEP on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WEP key being used. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the same WEP key that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WEP settings are correct. The WEP key must be exactly the same as on the wireless router.
Section 5 - Connecting to a Wireless Network Configure WPA-PSK It is recommended to enable WEP on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WEP key being used. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the same WPA-PSK passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router.
Section 6 - Setting Up Wi-Fi Protection (WCN 2.0 in Windows Vista) Setting Up Wi-Fi Protection (WCN 2.0 in Windows Vista) The TheDIR-619 DIR-618supports supportsWi-Fi Wi-Fiprotection, protection,referred referredtotoas asWCN WCN2.0 2.0ininWindows WindowsVista. Vista.The Theinstructions instructionsfor forsetting settingthis thisup up depend on whether you are using Windows Vista to configure the Router or third party software.
Section 6 - Setting Up Wi-Fi Protection (WCN 2.0 in Windows Vista) Setting Up a Configured Router Once the Router has been configured, you can use the push button on the Router or third party software to invite a newcomer to join your Wi-Fi protected network. For maximum security, the software method is recommended. However, the push button method is ideal if there is no access to a GUI.
Section 7 - Changing the Computer Name and Joining a Workgroup Changing the Computer Name and Joining a Workgroup The following are step-by-step directions to change the computer name and join a workgroup. 1. Click on Properties. 2. Click on the Advanced system settings link.
Section 7 - Changing the Computer Name and Joining a Workgroup 3. Click the Computer Name tab in the System Properties window and enter a description of your computer in the textbox. When you are finished, click the Change button. 4. Go to the Computer Name/Domain Changes window and click the radio button next to the Workgroup you want to join. When you are finished, click the OK button.
Section 8 - Configuring the IP Address in Vista Configuring the IP Address in Vista The following are step-by-step directions to configure the IP address in Windows Vista. 1. Click on Properties. 2. Go to the Network and Internet window and click the appropriate Local Area Connection icon. 3. Right-click the Local Area Connection icon and then select Properties from the drop-down menu.
Section 8 - Configuring the IP Address in Vista 4. Tick the Internet Protocol Version 4 (TCP/IPv4) checkbox in the Networking tab in the Local Area Connection Properties window. 5. Click the “Use the following IP address” option in the General tab in the Local Area Connections Properties window and enter the desired IP address in the space offered. Then click the “Use the following DNS server adresses” option on the same tab and enter the desired DNS server information.
Section 8 - Configuring the IP Address in Vista 6. Right-click the Local Area Connection icon and then select Status from the drop-down menu. 7. Go to the Local Area Connection Status window and click the Details button. 8. Confirm your new settings on the Network Connection Status window. When you are finished, click the Done button.
Section 9 - Setting Up a Connection Wirelessly Setting Up a Connection or Network Wirelessly The following are step-by-step directions to set up a wireless connection. 1. Click on Set up a connection or network in the Network and Sharing Center section. 2. Go to the Set up a connection or network window and choose the Set up a wireless router or access point Set up a new wireless network for your home or business option. Click the Next button.
Section 9 - Setting Up a Connection Wirelessly 3. Click the Next button on the Set up a wireless router or access point window. 4. The following window displays the system progress. 5. This window confirms that you want to create wireless network settings that are savable to a USB flash drive.
Section 9 - Setting Up a Connection Wirelessly 6. Enter a network name on the Give your network a name window in the Set up a wireless router or access point wizard. Click the Next button. 7. Enter a passphrase on the Help make your network more secure with a passphrase window in the Set up a wireless router or access point wizard. Click the Show advanced network security options link. 8.
Section 9 - Setting Up a Connection Wirelessly 9. Once you have selected the desired security method on the Choose advanced network security options window in the Set up a wireless router or access point wizard, click the Next button. 10.Select the desired file and printer sharing option on the Choose file and printer sharing options window in the Set up a wireless router or access point wizard. Click the Next button. 11.
Section 9 - Setting Up a Connection Wirelessly 12.Once you have saved your network settings to USB, the Copying settings to the USB drive window in the Set up a wireless router or access point wizard opens to indicate the system progress. 13.Once you are finished, the To add a device or computer, follow these instructions window in the Set up a wireless router or access point wizard opens. When you are finished, click the Close button.
Section 10 - Connecting to a Secured Wireless Network (WEP, WPA-PSK & WPA2-PSK) Connecting to a Secured Wireless Network (WEP, WPA-PSK & WPA2-PSK) The following are step-by-step directions to set up a wireless connection. 1. Click on Properties. 2. Click the Manage network connections link in the Network and Sharing Center window.
Section 10 - Connecting to a Secured Wireless Network (WEP, WPA-PSK & WPA2-PSK) 3. Right-click the Wireless Network Connection entry and then select Connect/Disconnect from the drop-down menu. 4. Select a network to connect to in the Select a network to connect to window in the Connect to a network wizard and then click the Connect button. 5. The following Connect to a network wizard window displays the system progress.
Section 10 - Connecting to a Secured Wireless Network (WEP, WPA-PSK & WPA2-PSK) 6. Enter the network security key or passphrase for the Router in the textbox provided in the Type the network security key or passphrase for dlink window in the Connect a network wizard. When you are finished, click the Connect button. 7. The following Successfully connected to dlink window in the Connect to a network wizard is displayed. Choose to save to the network and/or start the new connection automatically.
Section 10 - Connecting to a Secured Wireless Network (WEP, WPA-PSK & WPA2-PSK) 9. Confirm your new settings by calling up the command prompt and then entering the ipconfig command. 10.To test the new IP address, use the Ping feature of the command prompt.
Section 11 - Connecting to an Unsecured Wireless Network Connecting to an Unsecured Wireless Network The following are step-by-step directions to set up an unsecured wireless connection. 1. Click on Properties. 2. Go to the Network and Sharing Center window and click the Manage Network Connections link.
Section 11 - Connecting to an Unsecured Wireless Network 3. Right-click the Wireless Network Connection entry and then select Connect/Disconnect from the drop-down menu. 4. Select a network to connect to in the Select a network to connect to window in the Connect to a network wizard and then click the Connect button. 5. Confirm your desire to connect anyway on the following Network Connection Status window.
Section 11 - Connecting to an Unsecured Wireless Network 6. The following Connect to a network wizard window displays the system progress. 7. The following Successfully connected to dlink window in the Connect to a network wizard is displayed. Choose to save to the network and/or start the new connection automatically. When you are finished, click the Close button. 8. The successful connection is displayed at the bottom of the Windows start up menu.
Section 11 - Connecting to an Unsecured Wireless Network 9. Confirm your new settings by calling up the command prompt and then entering the ipconfig command. 10.To test the new IP address, use the Ping feature of the command prompt.
Section 12 - Troubleshooting Troubleshooting This to to problems thatthat cancan occur during the installation and operation of theof DIR-619. Thischapter chapterprovides providessolutions solutions problems occur during the installation and operation the DIR-618. ® ® XP. If If Read the following descriptions if you are having problems. (The examples below are illustrated in Windows XP. Read the following descriptions if you are having problems.
Section 12 - Troubleshooting • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Section 12 - Troubleshooting 3. Why can’t I connect to certain sites or send and receive emails when connecting through my router? If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to.
Section 12 - Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size.
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Appendix A - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford.
Appendix A - Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Appendix A - Wireless Basics Wireless Modes Eliminate Interference Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency. Security Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router.
Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® XP - Click on Start > Control Panel > Network Connections. Windows® 2000 - From the desktop, right-click My Network Places > Properties. Step 2 Right-click on the Local Area Connection which represents your D-Link network adapter and select Properties.
Appendix E - Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • O n ly fo r p r o d u c ts p u r c h a s e d a n d d e liv e r e d w ith in th e fi fty s ta te s o f th e U n ite d S ta te s , th e D is tr ic t o f C o lu m b ia , U .S . P o s s e s s io n s or Protectorates, U.S.
Appendix E - Warranty Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation.
Appendix E - Warranty • After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. DLink will only replace the defective portion of the product and will not ship back any accessories.
Appendix E - Warranty IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT.
Appendix E - Warranty CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Federal Communication Commission Interference Statement Federal Communication Commission Interference Statement This equipment been tested and found to comply the limits Class B has with for a digital device, pursuant to Part the FCC Rules.
以下警語適用台灣地區 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大 功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用， 並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射 頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
