Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date 1.0 August 22, 2012 Description t *OJUJBM SFMFBTF GPS 3FWJTJPO " Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
Table of Contents Table of Contents Preface ................................................................................. i .BOVBM 3FWJTJPOT ........................................................................... i Trademarks ...................................................................................... i Product Overview .............................................................. 1 Package Contents .........................................................................
Table of Contents IPv6 Manual Setup.........................................................63 mydlink Settings .................................................................72 Advanced...............................................................................73 Virtual Server ...................................................................73 Port Forwarding .............................................................74 "QQMJDBUJPO 3VMFT ..........................................................
Table of Contents Networking Basics .........................................................135 Check your IP address ............................................................ 135 Statically Assign an IP address ............................................ 136 Technical Specifications ................................................137 Contacting Technical Support ......................................138 GPL Code Statement......................................................139 Warranty .............
Section 1 - Product Overview Product PackageOverview Contents %*3 - 8JSFMFTT / %VBM #BOE (JHBCJU 3PVUFS Ethernet Cable Power Adapter If any of the above items are missing, please contact your reseller. Note: Using a power supply with a different voltage rating than the one included with the DIR-836L will cause damage and void the warranty for this product.
Section 1 - Product Overview System Requirements Network Requirements t "O &UIFSOFU CBTFE $BCMF PS %4- NPEFN t *&&& O PS H XJSFMFTT DMJFOUT ()[ t *&&& O PS B XJSFMFTT DMJFOUT ()[ t &UIFSOFU Computer with the following: t 8JOEPXT¥ .
Section 1 - Product Overview Introduction 5IF % -JOL 8JSFMFTT / %VBM #BOE (JHBCJU 3PVUFS %*3 - DPNFT FRVJQQFE XJUI (JHBCJU QPSUT UP QSPWJEF TQFFET VQ to 10x faster than standard 10/100 ports. It also uses 802.11n technology with multiple intelligent antennas to maximize the speed and range of your wireless signal to significantly outperform 802.11g devices.
Section 1 - Product Overview Features t 'BTUFS 8JSFMFTT /FUXPSLJOH - 5IF %*3 - QSPWJEFT VQ UP .CQT XJSFMFTT DPOOFDUJPO XJUI PUIFS O wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. The performance of this 802.11n wireless router gives you the freedom of wireless networking at speeds faster than 802.11g.
Section 1 - Product Overview Hardware Overview Connections 1 2 3 4 5 6 1 USB Port 2 WPS Button 3 LAN Ports (1-4) 4 Internet Port Using an Ethernet cable, connect your broadband modem to this port. 5 Power Button Press the power button to power on and off. 6 1PXFS 3FDFQUPS D-Link DIR-836L User Manual Connect a USB flash drive to share content throughout your network. Press to start the WPS process. The Power LED will start to blink.
Section 1 - Product Overview Hardware Overview LEDs 1 2 1 Power LED 2 Internet LED D-Link DIR-836L User Manual A solid green light indicates a proper connection to the power supply. The light will blink green during the WPS process and will be solid orange during boot-up. A solid light indicates connection on the Internet port. If the LED is orange, the connection is good but the router cannot connect to the Internet.
Section 2 - Installation Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage.
Section 2 - Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Section 2 - Installation Manual Setup 5VSO Pò BOE VOQMVH ZPVS DBCMF PS %4- CSPBECBOE NPEFN 5IJT JT SFRVJSFE Modem 2. Position your router close to your modem and a computer. Place the router in an open area of your intended work area for better wireless coverage. 3. Unplug the Ethernet cable from your modem (or existing router if upgrading) that is connected to your computer. Plug it into the LAN port labeled 1 on the back of your router. The router is now connected to your computer.
Section 2 - Installation 4. Plug one end of the included blue Ethernet cable that came with your router into the yellow port labeled */5&3/&5 PO UIF CBDL PG UIF SPVUFS 1MVH UIF PUIFS FOE PG UIJT DBCMF JOUP UIF &UIFSOFU QPSU PO ZPVS NPEFN %*3 Modem USB WPS 1 2 INTERNET 3 Computer 4 INTERNET POWER 3FDPOOFDU UIF QPXFS BEBQUFS UP ZPVS DBCMF PS %4- CSPBECBOE NPEFN BOE XBJU GPS UXP NJOVUFT 6.
Section 2 - Installation Connect to an Existing Router Note: It is strongly recommended to replace your existing router with the DIR-836L instead of using both. If your modem is a combo router, you may want to contact your ISP or manufacturer’s user guide to put the router into Bridge mode, which will ‘turn off’ the router (NAT) functions.
Section 2 - Installation 6OEFS 3PVUFS 4FUUJOHT FOUFS BO BWBJMBCMF *1 BEESFTT BOE UIF TVCOFU NBTL PG ZPVS OFUXPSL $MJDL Save Settings to save your settings. Use this new IP address to access the configuration utility of the router in the future. Close the browser and change your computer’s IP settings back to the original values as in Step 1. 6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7.
Section 2 - Installation Configuration 5IFSF BSF TFWFSBM EJòFSFOU XBZT ZPV DBO DPOöHVSF ZPVS SPVUFS UP DPOOFDU UP UIF *OUFSOFU BOE DPOOFDU UP ZPVS DMJFOUT t % -JOL 4FUVQ 8J[BSE 5IJT XJ[BSE XJMM MBVODI XIFO ZPV MPH JOUP UIF SPVUFS GPS UIF öSTU UJNF 3FGFS UP QBHF t QRS Mobile App 6TF ZPVS J1IPOF J1BE PS J1PE 5PVDI UP DPOöHVSF ZPVS SPVUFS 3FGFS UP QBHF t Manual Setup -PH JOUP UIF SPVUFS BOE NBOVBMMZ DPOöHVSF ZPVS SPVUFS BEWBODFE VTFST POMZ 3FGFS UP QBHF D-Link DIR-836L User Manua
Section 3 - Configuration Quick Setup Wizard If this is your first time installing the router, open your web CSPXTFS :PV XJMM BVUPNBUJDBMMZ CF EJSFDUFE UP UIF Wizard Setup Screen. If you have already configured your settings and you would like to access the configuration utility, please refer to page 26. This wizard is designed to guide you through a step-by-step process to configure your new D-Link router and connect to the Internet. Click Next to continue.
Section 3 - Configuration If the router does not detect a valid Ethernet connection from the Internet port, this screen will appear. Connect your broadband modem to the Internet port and then click Connect. If the router detects an Ethernet connection but does not detect the type of Internet connection you have, this screen will appear. Click Guide me through the Internet Connection Settings to display a list of connection types to choose from.
Section 3 - Configuration If the router detected or you selected PPPoE, enter your PPPoE username and password and click Next to continue. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work with a router. If the router detected or you selected PPTP, enter your PPTP username, password, and other information supplied by your ISP. Click Next to continue.
Section 3 - Configuration If the router detected or you selected Static, enter the IP and DNS settings supplied by your ISP. Click Next to continue. For both the 2.4GHz and 5GHz segments, create a wireless network a name (SSID) using up to 32 characters. Create a wireless security passphrase or key (between 8-63 characters). :PVS XJSFMFTT DMJFOUT XJMM OFFE UP IBWF UIJT QBTTQISBTF PS LFZ FOUFSFE to be able to connect to your wireless network. Click Next to continue.
Section 3 - Configuration Select your time zone from the drop-down menu and click Next to continue. The Setup Complete window will display your wireless settings. Click Save and Connect to continue. If you want to create a bookmark to the router, click OK. Click Cancel if you do not want to create a bookmark. If you clicked Yes, a window may appear (depending on what web browser you are using) to create a bookmark.
Section 3 - Configuration To use the mydlink service (mydlink.com or the mydlink Lite app), you must have an account. Select if you do have a mydlink account or if you need to create one. Click Next to continue. If you do not want to register at this time, click Cancel. If you clicked Yes, enter your mydlink account name (email address) and password. Click Login to register your router. If you clicked No öMM PVU UIF SFRVFTUFE JOGPSNBUJPO BOE DMJDL Next to create your mydlink account.
Section 3 - Configuration The mydlink App will allow you to receive notices, browse network users, and configure your router from an iPhone/iPad/iPod Touch (iOS 3.0 or higher), Android device (1.6 or higher). To download the "mydlink lite" app, visit the Apple Store, Android Market or http://mydlink.com/Lite. PC and Mac users can use the mydlink portal at http://mydlink.com.
Section 3 - Configuration QRS Mobile App Set up the router using your iPad or iPhone D-Link offers an app for your iPad, iPod Touch, or iPhone (iOS 4.3 or higher) to install and configure your router. Step 1 From your mobile device, go to the iTunes Store or Google Play and search for ‘D-Link’. Select QRS Mobile and then download it. Step 2 Once your app is installed, you may now configure your router. Connect to the router wirelessly by going to your wireless utility on your device.
Section 3 - Configuration SharePort Mobile App The SharePort Mobile makes it simple to access media saved on your USB drive right from your iPhone, iPad or Android device. Just follow the three TJNQMF TUFQT CFMPX 1. Download the SharePort Mobile App from the Apple App store or the Google Play store to your mobile device. 2.
Section 3 - Configuration 3. From your mobile device, click Settings. Settings 4. iOS - Press Wi-Fi, select the wireless network (SSID) that you created in the setup and then enter your Wi-Fi password. Android - Press Wireless & Networks > 8J 'J 4FUUJOHT and then select the wireless network (SSID) that you created in the setup. Enter your Wi-Fi password. 5. Once connected, click on the SharePort Mobile icon.
Section 3 - Configuration 6. The following screen will appear. 7. Click on Settings icon located on the right top corner of the screen. Click Edit to enter your User Name and Password. Once you finish, click Done to continue. 8. For the Movie section, click the movie icon to play your movie from your USB flash drive. 9. For the Music section, click the music icon to play your music from your USB flash drive.
Section 3 - Configuration 10. For the Photo section, click the Photo icon to view your photos from your USB flash drive. 11. For the Files section, click on the Files icon to view your files from your USB flash drive. 12. For the Folder section, click the folder icon to view your folders from your USB flash drive.
Section 3 - Configuration Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter http://dlinkrouter.local. :PV NBZ BMTP DPOOFDU CZ UZQJOH UIF SPVUFS T -"/ *1 BEESFTT (http://192.168.0.1) in the address bar. Enter your password and click Log In. Leave the password blank by default.
Section 3 - Configuration Internet Connection Setup Click Manual Internet Connection Setup to configure your connection manually and continue to the next page. If you want to configure your router to connect to the Internet using the wizard, click *OUFSOFU $POOFDUJPO 4FUVQ 8J[BSE. :PV XJMM CF EJSFDUFE UP UIF 2VJDL 4FUVQ 8J[BSE 1MFBTF SFGFS to page 14.
Section 3 - Configuration Manual Internet Setup Static (assigned by ISP) 4FMFDU 4UBUJD *1 "EESFTT JG BMM UIF *OUFSOFU QPSU T *1 JOGPSNBUJPO JT QSPWJEFE UP ZPV CZ ZPVS *41 :PV XJMM OFFE UP FOUFS JO UIF *1 BEESFTT TVCOFU NBTL gateway address, and DNS address(es) provided to you by your ISP.
Section 3 - Configuration MAC Address: 5IF EFGBVMU ."$ "EESFTT JT TFU UP UIF *OUFSOFU QPSU T QIZTJDBM JOUFSGBDF ."$ BEESFTT PO UIF #SPBECBOE 3PVUFS *U JT OPU SFDPNNFOEFE UIBU ZPV DIBOHF UIF EFGBVMU ."$ BEESFTT VOMFTT SFRVJSFE CZ ZPVS *41 :PV DBO VTF UIF Copy Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
Section 3 - Configuration Dynamic (Cable) My Internet Select Dynamic IP (DHCP) to obtain IP Address information Connection: automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for cable modem services. Enable Advanced Advanced Domain Name System (DNS) services enhances your Internet DNS Service: performance by getting you the information and web pages you are looking for faster and more reliably.
Section 3 - Configuration Internet Setup PPPoE (DSL) $IPPTF 111P& 1PJOU UP 1PJOU 1SPUPDPM PWFS &UIFSOFU JG ZPVS *41 VTFT B 111P& DPOOFDUJPO :PVS *41 XJMM QSPWJEF ZPV XJUI B username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. My Internet Select PPPoE (Username/Password) from the drop-down menu.
Section 3 - Configuration Maximum Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Idle Time: Auto-reconnect. DNS Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only). Addresses: MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the default MTU. MAC Address: 5IF EFGBVMU ."$ "EESFTT JT TFU UP UIF *OUFSOFU QPSU T QIZTJDBM JOUFSGBDF .
Section 3 - Configuration Internet Setup PPTP $IPPTF 1151 1PJOU UP 1PJOU 5VOOFMJOH 1SPUPDPM JG ZPVS *41 VTFT B 1151 DPOOFDUJPO :PVS *41 XJMM QSPWJEF ZPV XJUI B VTFSOBNF and password. This option is typically used for DSL services. My Internet Select PPTP (Username/Password) from the drop-down menu.
Section 3 - Configuration Username: Enter your PPTP username. Password: Enter your PPTP password and then retype the password in the next box. Reconnect Select either Always-on, On-Demand, or Manual. Mode: Maximum Idle Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Time: Auto-reconnect. DNS Servers: The DNS server information will be supplied by your ISP (Internet Service Provider.
Section 3 - Configuration Internet Setup L2TP $IPPTF - 51 -BZFS 5VOOFMJOH 1SPUPDPM JG ZPVS *41 VTFT B - 51 DPOOFDUJPO :PVS *41 XJMM QSPWJEF ZPV XJUI B VTFSOBNF BOE password. This option is typically used for DSL services. My Internet Select L2TP (Username/Password) from the drop-down menu. Connection: Enable Advanced Domain Name System (DNS) services enhances your Advanced DNS Internet performance by getting you the information and web Service: pages you are looking for faster and more reliably.
Section 3 - Configuration Username: Enter your L2TP username. Password: Enter your L2TP password and then retype the password in the next box. Reconnect Select either Always-on, On-Demand, or Manual. Mode: Maximum Idle Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Time: Auto-reconnect. DNS Servers: Enter the Primary and Secondary DNS Server Addresses (Static L2TP only).
Section 3 - Configuration Wireless Settings If you want to configure the wireless settings on your router using the wizard, click 8JSFMFTT 4FDVSJUZ 4FUVQ 8J[BSE and refer to page 41. Click Add Wireless Device with WPS if you want to add a wireless device using Wi-Fi Protected Setup (WPS) and refer to page 43. If you want to manually configure the wireless settings on your router click Manual Wireless Network Setup and refer to the next page.
Section 3 - Configuration Manual Wireless Settings 802.11n/g (2.4GHz) Enable Wireless: Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Schedule: Select the time frame that you would like your wireless network enabled. The schedule may be set to Always. Any schedule you create will be available in the drop-down menu. Click Add New to create a schedule.
Section 3 - Configuration 802.11n/a (5GHz) Enable Wireless: Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Schedule: Select the time frame that you would like your wireless network enabled. The schedule may be set to Always. Any schedule you create will be available in the drop-down menu. Click New Schedule to create a schedule. Wireless Network Service Set Identifier (SSID) is the name of your wireless network.
Section 4 - Security Wireless Security 5IJT TFDUJPO XJMM TIPX ZPV UIF EJòFSFOU MFWFMT PG TFDVSJUZ ZPV DBO VTF UP QSPUFDU ZPVS EBUB GSPN JOUSVEFST 5IF %*3 - PòFST UIF GPMMPXJOH UZQFT PG TFDVSJUZ t 81" 8J 'J 1SPUFDUFE "DDFTT t 81" 8J 'J 1SPUFDUFE "DDFTT t 81" 14, 1SF 4IBSFE ,FZ t 81" 14, 1SF 4IBSFE ,FZ What is WPA? 81" 8J 'J 1SPUFDUFE "DDFTT JT B 8J 'J TUBOEBSE UIBU XBT EFTJHOFE UP JNQSPWF UIF TFDVSJUZ GFBUVSFT PG 8&1 8JSFE &RVJWBMFOU 1SJWBDZ 5
Section 4 - Security Wireless Security Setup Wizard To run the security wizard, click on Setup at the top and then click 8JSFMFTT /FUXPSL 4FUVQ 8J[BSE. Type your desired wireless network name (SSID). Automatically: Select this option to automatically generate the router’s network key and click Next. Manually: Select this option to manually enter your network key and click Next.
Section 4 - Security If you selected Automatically, the summary window will display your settings. Write down the security key and enter this on your wireless clients. Click Save to save your settings. If you selected Manually, the following screen will appear. Create a passphrase for your security password. Click Next to continue.
Section 4 - Security Add Wireless Device with WPS Wizard From the Setup > Wireless Settings screen, click Add Wireless Device with WPS. Select Auto to add a wireless client using WPS (Wi-Fi Protected Setup) and then click Next. Skip to the next page. If you select Manual, a settings summary screen will appear. Write down the security key and enter this on your wireless clients. Click OK to finish.
Section 4 - Security PIN: Select this option to use PIN method. In order to use this method you must know the wireless client’s 8 digit PIN and click Connect. PBC: Select this option to use PBC (Push Button) method to add a wireless client. Click Connect. Once you click Connect, you will have a 120 second time limit to apply the settings to your wireless client(s) and successfully establish a connection.
Section 4 - Security WPA/WPA2-Personal (PSK) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish XJSFMFTT DPOOFDUJWJUZ CFGPSF FOBCMJOH FODSZQUJPO :PVS XJSFMFTT TJHOBM NBZ EFHSBEF XIFO FOBCMJOH FODSZQUJPO EVF UP UIF added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Setup and then click Wireless Settings on the left side. 2.
Section 4 - Security Configure WPA/WPA2-Enterprise (RADIUS) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish XJSFMFTT DPOOFDUJWJUZ CFGPSF FOBCMJOH FODSZQUJPO :PVS XJSFMFTT TJHOBM NBZ EFHSBEF XIFO FOBCMJOH FODSZQUJPO EVF UP UIF added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Setup and then click Wireless Settings on the left side. 2.
Section 4 - Security 8. Next to RADIUS Server Port, enter the port you are using with ZPVS 3"%*64 TFSWFS JT UIF EFGBVMU QPSU 9. Next to RADIUS Server Shared Secret, enter the security key. 10. If the MAC Address Authentication box is selected then the user will need to connect from the same computer whenever logging into the wireless network. 11. Click Advanced UP FOUFS TFUUJOHT GPS B TFDPOEBSZ 3"%*64 4FSWFS 12. Click Apply Settings to save your settings.
Section 3 - Configuration Network Settings This section will allow you to change the local network settings of the router and to configure the DHCP settings. Router Settings Router IP Enter the IP address of the router. The default IP address Address: is 192.168.0.1. If you change the IP address, once you click Save Settings, you will need to enter the new IP address in your browser to get back into the configuration utility. Subnet Mask: Enter the Subnet Mask. The default subnet mask is 255.255.255.0.
Section 3 - Configuration DHCP Server Settings %)$1 TUBOET GPS %ZOBNJD )PTU $POUSPM 1SPUPDPM 5IF %*3 - IBT B CVJMU JO %)$1 TFSWFS 5IF %)$1 4FSWFS XJMM BVUPNBUJDBMMZ assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.
Section 3 - Configuration NetBIOS Node: Select the different type of NetBIOS node; Broadcast only, Point-to-Point, Mixed-mode, and Hybrid. WINS IP Enter your WINS Server IP address(es).
Section 3 - Configuration DHCP Reservation If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range. Enable: Check this box to enable the reservation. Computer Name: Enter the computer name or select from the drop-down menu and click <<. IP Address: Enter the IP address you want to assign to the computer or device.
Section 3 - Configuration Storage The Storage option will allow you to access files from a USB external hard drive or thumb drive that is plugged into the router GSPN ZPVS MPDBM OFUXPSL PS GSPN UIF *OUFSOFU VTJOH FJUIFS B XFC CSPXTFS PS BO BQQ GPS ZPVS TNBSUQIPOF PS UBCMFU :PV DBO create users to be allowed to access these files. 4IBSF1PSU .PCJMF 8FC "DDFTT 4FUVQ 8J[BSE Click this button to launch the setup wizard.
Section 3 - Configuration Setup Wizard Step 1 - Make sure you have plugged in a USB thumb drive or external hard drive into the USB port on the router. Click Next to continue. Step 2 - Create a user account and a password. This is only to access the shared files on your USB device. Click Next to continue. Step 3 - Select the folder from your USB drive that you want to share. Click Select to choose the folder. Note that all subfolders under the folder you want to share will be shared.
Section 3 - Configuration Step 4 - Once you select your folder, the path will appear in the box. Click Next to continue. Step 5 - Enter your Dynamic DNS (DDNS) information if you want to VTF B 63- JOTUFBE PG BO *1 BEESFTT UP BDDFTT ZPVS TIBSFE öMFT GSPN UIF Internet. Click Next to continue. If you do not have or want an account, leave the boxes empty and click Next. If you would like a DDNS account through D-Link, click the www. dlinkddns.com link to create a new account. Step 6 - Setup is complete.
Section 3 - Configuration Manual Setup Here you may manually configure the Storage settings such as access ports, create/edit user accounts, and create shares from your USB storage device. Please skip to the next page for step-by-step instructions. Enable SharePort Check to enable sharing files on your USB storage device that Web Access: is plugged in your router. This option is disabled by default.
Section 3 - Configuration Access Files from the Internet *G ZPV XPVME MJLF UP BDDFTT ZPVS öMFT UIBU BSF PO ZPVS 64# UIVNC ESJWF PS FYUFSOBM IBSE ESJWF UIBU JT DPOOFDUFE UP ZPVS SPVUFS GPMMPX UIF TUFQT CFMPX Step 1 - Enable SharePort Web Access Check the Enable SharePort Web Access checkbox to enable. Then enter the port(s) you want to use for HTTP and HTTPS. The default for HTTP is 8181 and HTTPS is 4433.
Section 3 - Configuration IPv6 0O UIJT QBHF UIF VTFS DBO DPOöHVSF UIF *1W $POOFDUJPO UZQF 5IFSF BSF UXP XBZT UP TFU VQ UIF *1W *OUFSOFU DPOOFDUJPO :PV can use the Web-based IPv6 Internet Connection Setup Wizard, or you can manually configure the connection. For the beginner user that has not configured a router before, click on the *1W *OUFSOFU $POOFDUJPO 4FUVQ 8J[BSE button and the router will guide you through a few simple steps to get your network up and running.
Section 3 - Configuration IPv6 Internet Connection Setup Wizard On this page, the user can configure the IPv6 Connection type using the IPv6 Internet Connection Setup Wizard. Click the *1W *OUFSOFU $POOFDUJPO 4FUVQ 8J[BSE button and the router will guide you through a few simple steps to get your network up and running. Click Next to continue to the next page. Click Cancel to discard the changes made and return to the main page.
Section 3 - Configuration However, if the automatic detection fails, the user will be prompt to either Try again or to click on the Guide me through the IPv6 settings button to initiate the manual continual of the wizard. There are several connection types to choose from. If you are unsure of your connection method, please contact your IPv6 Internet Service Provider. Note: If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or disabled.
Section 3 - Configuration IPv6 over PPPoE After selecting the IPv6 over PPPoE option, the user will be able to configure the *1W *OUFSOFU DPOOFDUJPO UIBU SFRVJSFT B VTFSOBNF BOE QBTTXPSE UP HFU POMJOF Most DSL modems use this type of connection. 5IF GPMMPXJOH QBSBNFUFST XJMM CF BWBJMBCMF GPS DPOöHVSBUJPO PPPoE Session: Select the PPPoE Session value used here.
Section 3 - Configuration Static IPv6 Address Connection This mode is used when your ISP provides you with a set IPv6 addresses that does not change.
Section 3 - Configuration Tunneling Connection (6rd) After selecting the Tunneling Connection (6rd) option, the user can configure the IPv6 6rd connection settings. 5IF GPMMPXJOH QBSBNFUFST XJMM CF BWBJMBCMF GPS DPOöHVSBUJPO 6rd IPv6 Prefix: Enter the 6rd IPv6 address and prefix value used here. IPv4 Address: Enter the IPv4 address used here. Mask Length: Enter the IPv4 mask length used here. Assigned IPv6 Prefix: Displays the IPv6 assigned prefix value here.
Section 3 - Configuration IPv6 Manual Setup 5IFSF BSF TFWFSBM DPOOFDUJPO UZQFT UP DIPPTF GSPN "VUP %FUFDUJPO 4UBUJD *1W "VUPDPOöHVSBUJPO 4-""$ %)$1W 111P& IPv6 in IPv4 Tunnel, 6to4, 6rd, and Link-local. If you are unsure of your connection method, please contact your IPv6 Internet Service Provider. Note: If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or disabled.
Section 3 - Configuration Static IPv6 My IPv6 Connection: Select Static IPv6 from the drop-down menu. WAN IPv6 Address Enter the address settings supplied by your Internet provider Settings: (ISP). LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN Link-Local Address: %JTQMBZT UIF 3PVUFS T -"/ -JOL -PDBM "EESFTT Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Type: Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless DHCPv6.
Section 3 - Configuration Autoconfiguration My IPv6 Connection: Select Autoconfiguration (Stateless/DHCPv6) from the drop-down menu. IPv6 DNS Settings: Select either Obtain DNS server address automatically or Use the following DNS Address. Primary/Secondary DNS Enter the primary and secondary DNS server addresses. Address: LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router.
Section 3 - Configuration PPPoE My IPv6 Connection: Select PPPoE from the drop-down menu. PPPoE: Enter the PPPoE account settings supplied by your Internet provider (ISP). Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. IP Address: Enter the IP address (Static PPPoE only). User Name: Enter your PPPoE user name. Password: Enter your PPPoE password and then retype the password in the next box.
Section 3 - Configuration Autoconfiguration Type: Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless DHCPv6. IPv6 Address Range Start: Enter the start IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Range End: Enter the end IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Lifetime: Enter the IPv6 Address Lifetime (in minutes).
Section 3 - Configuration IPv6 in IPv4 Tunneling My IPv6 Select IPv6 in IPv4 Tunnel from the drop-down menu. Connection: IPv6 in IPv4 Tunnel Enter the settings supplied by your Internet provider (ISP). Settings: LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN Link-Local %JTQMBZT UIF 3PVUFS T -"/ -JOL -PDBM "EESFTT Address: Enable Check to enable the Autoconfiguration feature.
Section 3 - Configuration 6 to 4 Tunneling My IPv6 Connection: Select 6 to 4 from the drop-down menu. 6 to 4 Settings: Enter the IPv6 settings supplied by your Internet provider (ISP). Primary/Secondary Enter the primary and secondary DNS server addresses. DNS Address: LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN Link-Local %JTQMBZT UIF 3PVUFS T -"/ -JOL -PDBM "EESFTT Address: Enable Check to enable the Autoconfiguration feature.
Section 3 - Configuration 6rd My IPv6 Connection: Select 6rd from the drop-down menu. 6RD Settings: Enter the address settings supplied by your Internet provider (ISP). LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN Link-Local Address: %JTQMBZT UIF 3PVUFS T -"/ -JOL -PDBM "EESFTT Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Type: Select Stateful (DHCPv6), SLAAC+RDNSS or SLAAC + Stateless DHCPv6.
Section 3 - Configuration Link-Local Connectivity My IPv6 Connection: Select Link-Local Only from the drop-down menu. LAN IPv6 Address Displays the IPv6 address of the router.
Section 3 - Configuration mydlink Settings mydlink Service: Displays whether your device is registered with a mydlink account or not. Register mydlink Click to go to the mydlink website to register or edit your Settings: settings.
Section 3 - Configuration Advanced Virtual Server This will allow you to open a single port. If you would like to open a range of ports, refer to the next page. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Configuration Port Forwarding This will allow you to open a single port or a range of ports. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Configuration Application Rules 4PNF BQQMJDBUJPOT SFRVJSF NVMUJQMF DPOOFDUJPOT TVDI BT *OUFSOFU HBNJOH WJEFP DPOGFSFODJOH *OUFSOFU UFMFQIPOZ BOE PUIFST These applications have difficulties working through NAT (Network Address Translation).
Section 3 - Configuration QoS Engine The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classified automatically. Enable QoS Engine: This option is disabled by default. Enable this option for better performance and experience with online games and other interactive applications, such as VoIP. Automatic Uplink This option is enabled by default when the QoS Engine option is enabled.
Section 3 - Configuration Network Filters Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from BDDFTTJOH UIF OFUXPSL :PV DBO FJUIFS NBOVBMMZ BEE B ."$ BEESFTT PS TFMFDU UIF ."$ BEESFTT GSPN UIF MJTU PG DMJFOUT UIBU BSF DVSSFOUMZ DPOOFDUFE UP UIF #SPBECBOE 3PVUFS Configure MAC Select 5VSO ."$ 'JMUFSJOH 0ò, Allow MAC addresses Filtering: listed below, or Deny MAC addresses listed below from the drop-down menu.
Section 3 - Configuration Access Control The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to only grant access to approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games. Add Policy: Click the Add Policy button to start the Access Control Wizard. Access Control Wizard Click Next to continue with the wizard.
Section 3 - Configuration Enter a name for the policy and then click Next to continue. Select a schedule (I.E. Always) from the drop-down menu and then click Next to continue. Enter the following information and then click Next to continue. t Address Type - Select IP address, MAC address, or Other Machines. t IP Address - Enter the IP address of the computer you want to apply the rule to. t Machine Address &OUFS UIF 1$ .
Section 3 - Configuration &OUFS UIF SVMF Enable - Check to enable the rule. Name - Enter a name for your rule. Dest IP Start - Enter the starting IP address. Dest IP End - Enter the ending IP address. Protocol - Select the protocol. Dest Port Start - Enter the starting port number. Dest Port End - Enter the ending port number. To enable web logging, click Enable. Click Save to save the access control rule. :PVS OFXMZ DSFBUFE QPMJDZ XJMM OPX TIPX VQ VOEFS Policy Table.
Section 3 - Configuration Website Filters Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network. To use this feature select to Allow or Deny, enter the domain or website and click Save Settings :PV NVTU BMTP TFMFDU Apply 8FC 'JMUFS under the Access Control section (page 78). Add Website Select either DENY computers access to ONLY Filtering Rule: these sites or ALLOW computers access to ONLY these sites.
Section 3 - Configuration Inbound Filters The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can configure inbound data filtering rules that control data based on an IP address range. Inbound Filters can be used with Virtual 4FSWFS 1PSU 'PSXBSEJOH PS 3FNPUF "ENJOJTUSBUJPO GFBUVSFT Name: Enter a name for the inbound filter rule. Action: Select Allow or Deny. Enable: Check to enable rule. Remote IP Start: Enter the starting IP address.
Section 3 - Configuration Firewall Settings " öSFXBMM QSPUFDUT ZPVS OFUXPSL GSPN UIF PVUTJEF XPSME 5IF %*3 - PòFST B öSFXBMM UZQF GVODUJPOBMJUZ 5IF 41* GFBUVSF IFMQT prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
Section 3 - Configuration RTSP: "MMPXT BQQMJDBUJPO UIBU VTFT 3FBM 5JNF 4USFBNJOH 1SPUPDPM UP SFDFJWF TUSFBNJOH NFEJB GSPN UIF *OUFSOFU 2VJDL5JNF BOE 3FBM 1MBZFS are some of the common applications using this protocol. SIP: Allows devices and applications using VoIP (Voice over IP) to communicate across NAT. Some VoIP applications and devices have the ability to discover NAT devices and work around them. This ALG may interfere with the operation of such devices.
Section 3 - Configuration Routing 5IF 3PVUJOH PQUJPO JT BO BEWBODFE NFUIPE PG DVTUPNJ[JOH TQFDJöD SPVUFT PG EBUB UISPVHI ZPVS OFUXPSL Name: Enter a name for your route. Destination IP: Enter the IP address of packets that will take this route. Netmask: Enter the netmask of the route, please note that the octets must match your destination IP address. Gateway: Enter your next hop gateway to be taken if this route is used.
Section 3 - Configuration Advanced Wireless Transmit Power: Set the transmit power of the antennas. WLAN Partition: This enables 802.11d operation. 802.11d is a wireless specification developed to allow implementation of wireless networks in countries that cannot use the 802.11 standard. This feature should only be enabled JG ZPV BSF JO B DPVOUSZ UIBU SFRVJSFT JU WMM Enable: WMM is QoS for your wireless network.
Section 3 - Configuration Wi-Fi Protected Setup (WPS) Wi-Fi Protected Setup (WPS) System is a simplified method for securing your wireless network during the “Initial setup” as well as the “Add New Device” processes. The Wi-Fi Alliance (WFA) has certified it across different products as well as manufactures. The process is just as easy as pressing a button for the Push-Button Method or correctly entering the 8-digit code for the Pin $PEF .
Section 3 - Configuration Add Wireless This Wizard helps you add wireless devices to the wireless network. Station: The wizard will either display the wireless network settings to guide you through manual configuration, prompt you to enter the PIN for the device, or ask you to press the configuration button on the device.
Section 3 - Configuration Advanced Network Settings Enable UPnP: To use the Universal Plug and Play (UPnP™) feature click on Enabled. UPnP provides compatibility with OFUXPSLJOH FRVJQNFOU TPGUXBSF BOE QFSJQIFSBMT WAN Ping: $IFDLJOH UIF CPY XJMM BMMPX UIF %*3 - UP SFTQPOE to pings. Unchecking the box may provide some extra security from hackers.
Section 3 - Configuration Guest Zone The Guest Zone feature will allow you to create temporary zones that can be used by guests to access the Internet. These zones XJMM CF TFQBSBUF GSPN ZPVS NBJO XJSFMFTT OFUXPSL :PV NBZ DPOöHVSF EJòFSFOU [POFT GPS UIF ()[ BOE ()[ XJSFMFTT CBOET Enable Guest Check to enable the Guest Zone feature. Zone: Schedule: The schedule of time when the Guest Zone will be active.
Section 3 - Configuration IPv6 Firewall 5IF %*3 - T *1W 'JSFXBMM GFBUVSF BMMPXT ZPV UP DPOöHVSF XIJDI LJOE PG *1W USBóD JT BMMPXFE UP QBTT UISPVHI UIF EFWJDF 5IF %*3 - T *1W 'JSFXBMM GVODUJPOT JO B TJNJMBS XBZ UP UIF *1 'JMUFST GFBUVSF Enable Checkbox: Check the box to enable the IPv6 firewall simple security. Configure IPv6 Select an action from the drop-down menu. Firewall: Name: Enter a name to identify the IPv6 firewall rule.
Section 3 - Configuration IPv6 Routing This page allows you to specify custom routes that determine how data is moved around your network. Route List: Check the box next to the route you wish to enable. Name: Enter a specific name to identify this route. Destination IP/ This is the IP address of the router used to reach the Prefix Length: specified destination or enter the IPv6 address prefix length of the packets that will take this route. Metric: Enter the metric value for this rule here.
Section 3 - Configuration Tools Admin 5IJT QBHF XJMM BMMPX ZPV UP DIBOHF UIF "ENJOJTUSBUPS BOE 6TFS QBTTXPSET :PV DBO BMTP FOBCMF 3FNPUF .BOBHFNFOU 5IFSF BSF two accounts that can access the management interface through the web browser. The accounts are admin and user. Admin has read/write access while user has read-only access. User can only view the settings but cannot make any changes. Only the admin account has the ability to change both admin and user account passwords.
Section 3 - Configuration Time The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to automatically adjust the time when needed. Time: Displays the current date and time of the router. Time Zone: Select your Time Zone from the drop-down menu.
Section 3 - Configuration SysLog 5IF #SPBECBOE 3PVUFS LFFQT B SVOOJOH MPH PG FWFOUT BOE BDUJWJUJFT PDDVSSJOH PO UIF 3PVUFS :PV NBZ TFOE UIFTF MPHT UP B SysLog server on your network. Enable Logging to Check this box to send the router logs to a SysLog SysLog Server: Server. SysLog Server IP The address of the SysLog server that will be Address: VTFE UP TFOE UIF MPHT :PV NBZ BMTP TFMFDU ZPVS computer from the drop-down menu (only if receiving an IP address from the router via DHCP).
Section 3 - Configuration Email Settings The Email feature can be used to send the system log files, router alert messages, and firmware update notification to your email address. Enable Email When this option is enabled, router activity logs are emailed to a Notification: designated email address. From Email Address: This email address will appear as the sender when you receive a log file or firmware upgrade notification via email. To Email Address: Enter the email address where you want the email sent.
Section 3 - Configuration System This section allows you to manage the router’s configuration settings, reboot the router, and restore the router to the factory EFGBVMU TFUUJOHT 3FTUPSJOH UIF VOJU UP UIF GBDUPSZ EFGBVMU TFUUJOHT XJMM FSBTF BMM TFUUJOHT JODMVEJOH BOZ SVMFT UIBU ZPV WF DSFBUFE Save Settings to Use this option to save the current router Local Hard Drive: configuration settings to a file on the hard disk of the computer you are using. First, click the Save button.
Section 3 - Configuration Firmware :PV DBO VQHSBEF UIF öSNXBSF PG UIF BDDFTT QPJOU IFSF .BLF TVSF UIF öSNXBSF ZPV XBOU UP VTF JT PO UIF MPDBM IBSE ESJWF PG the computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support website for firmware updates at http://support.dlink.
Section 3 - Configuration Dynamic DNS The DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.
Section 3 - Configuration System Check Ping Test: The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP address that you wish to Ping and click Ping. IPv6 Ping Test: Enter the IPv6 address that you wish to Ping and click Ping. Ping Results: The results of your ping attempts will be displayed here.
Section 3 - Configuration Schedules Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm. Name: Enter a name for your new schedule. Days: Select a day, a range of days, or All Week to include every day. Time: Check All Day - 24hrs or enter a start and end time for your schedule.
Section 3 - Configuration Status Device Info 5IJT QBHF EJTQMBZT UIF DVSSFOU JOGPSNBUJPO GPS UIF %*3 - *U XJMM EJTQMBZ UIF -"/ 8"/ *OUFSOFU BOE 8JSFMFTT JOGPSNBUJPO If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed.
Section 3 - Configuration Logs The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained.
Section 3 - Configuration Statistics The screen below displays the Traffic Statistics )FSF ZPV DBO WJFX UIF BNPVOU PG QBDLFUT UIBU QBTT UISPVHI UIF %*3 - PO CPUI the WAN, LAN ports and the wireless segments. The traffic counter will reset if the device is rebooted.
Section 3 - Configuration Internet Sessions The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer.
Section 3 - Configuration Routing This page will display your current routing table.
Section 3 - Configuration Wireless The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients.
Section 3 - Configuration IPv6 5IF *1W QBHF EJTQMBZT B TVNNBSZ PG UIF 3PVUFS T *1W TFUUJOHT BOE MJTUT UIF *1W BEESFTT BOE IPTU OBNF PG BOZ *1W DMJFOUT D-Link DIR-836L User Manual 108
Section 3 - Configuration IPV6 Routing This page displays the IPV6 routing details configured for your router.
Section 3 - Configuration Support D-Link DIR-836L User Manual 110
Section 4 - Security Connect a Wireless Client to your Router WPS Button The easiest and most secure way to connect your wireless devices to the router is WPS (Wi-Fi Protected Setup).
Section 4 - Security Windows® 7 WPA/WPA2 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). Wireless Icon 2. The utility will display any available wireless networks in your area.
Section 4 - Security 3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your 5$1 *1 TFUUJOHT GPS ZPVS XJSFMFTT BEBQUFS 3FGFS UP UIF /FUXPSLJOH Basics section in this manual for more information. 4. The following window appears while your computer tries to connect to the router.
Section 4 - Security 5. Enter the same security key or passphrase that is on your router and click Connect :PV DBO BMTP DPOOFDU CZ QVTIJOH UIF 814 CVUUPO PO the router. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 4 - Security WPS 5IF 814 GFBUVSF PG UIF %*3 - DBO CF DPOöHVSFE VTJOH 8JOEPXT¥ $BSSZ PVU UIF GPMMPXJOH TUFQT UP VTF 8JOEPXT¥ UP DPOöHVSF UIF 814 GFBUVSF 1. Click the Start button and select Computer from the Start menu. 2. Click Network on the left side.
Section 4 - Security %PVCMF DMJDL UIF %*3 - 4. Input the WPS PIN number (displayed in the WPS window on the 3PVUFS T -$% TDSFFO PS JO UIF Setup > Wireless Setup menu in UIF 3PVUFS T 8FC 6* BOE DMJDL Next.
Section 4 - Security 5. Type a name to identify the network. 6. To configure advanced settings, click the icon. Click Next to continue.
Section 4 - Security 5IF GPMMPXJOH XJOEPX BQQFBST XIJMF UIF 3PVUFS JT CFJOH configured. Wait for the configuration to complete. 8. The following window informs you that WPS on the router has been setup successfully. Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future. 9. Click Close to complete WPS setup.
Section 5 - Connecting to a Wireless Network Windows Vista® Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista® utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility.
Section 5 - Connecting to a Wireless Network WPA/WPA2 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network. 2.
Section 5 - Connecting to a Wireless Network 3. Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 5 - Connecting to a Wireless Network WPS/WCN 2.0 The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista®. The following instructions for setting this up depends on whether you are using Windows Vista® to configure the router or third party software. When you first set up the router, Wi-Fi protection is disabled and unconfigured.
Section 5 - Connecting to a Wireless Network Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Section 5 - Connecting to a Wireless Network WPA/WPA2 It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA key being used. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router.
Section 6 - Troubleshooting Troubleshooting 5IJT DIBQUFS QSPWJEFT TPMVUJPOT UP QSPCMFNT UIBU DBO PDDVS EVSJOH UIF JOTUBMMBUJPO BOE PQFSBUJPO PG UIF %*3 - 3FBE UIF GPMMPXJOH descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples. 1. Why can’t I access the web-based configuration utility? When entering the IP address of the D-Link router (192.168.0.
Section 6 - Troubleshooting t $POöHVSF ZPVS *OUFSOFU TFUUJOHT t (P UP Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. t $MJDL UIF Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. t (P UP UIF Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Section 6 - Troubleshooting 3. Why can’t I connect to certain sites or send and receive emails when connecting through my router? If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to.
Section 6 - Troubleshooting :PV TIPVME TUBSU BU BOE XPSL ZPVS XBZ EPXO CZ FBDI UJNF 0ODF ZPV HFU B SFQMZ HP VQ CZ VOUJM ZPV HFU B GSBHNFOUFE packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size. 5P DIBOHF UIF .
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link XJSFMFTT GBNJMZ PG QSPEVDUT XJMM BMMPX ZPV UP TFDVSFMZ BDDFTT UIF EBUB ZPV XBOU XIFO BOE XIFSF ZPV XBOU JU :PV XJMM CF BCMF to enjoy the freedom that wireless networking delivers.
Appendix A - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio GSFRVFODZ UP DPOOFDU XJSFMFTTMZ TP ZPV IBWF UIF GSFFEPN UP DPOOFDU DPNQVUFST BOZXIFSF JO ZPVS IPNF PS PóDF OFUXPSL Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford.
Appendix A - Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Appendix A - Wireless Basics Security Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on UIF 81" PS 8&1 TFDVSJUZ GFBUVSF PO UIF SPVUFS 3FGFS UP QSPEVDU NBOVBM GPS EFUBJM JOGPSNBUJPO PO IPX UP TFU JU VQ Wireless Modes 5IFSF BSF CBTJDBMMZ UXP NPEFT PG OFUXPSLJOH t Infrastructure – All wireless clients will connect to an access point or wireless router.
Appendix B - Networking Basics Networking Basics Check your IP address To check your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter. If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router.
Appendix B - Networking Basics Statically Assign an IP address *G ZPV BSF OPU VTJOH B %)$1 DBQBCMF HBUFXBZ SPVUFS PS ZPV OFFE UP BTTJHO B TUBUJD *1 BEESFTT QMFBTF GPMMPX UIF TUFQT CFMPX Step 1 Windows® 7 Click on Start > Control Panel > Network and Internet > Network and Sharing Center. Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. Windows® XP Click on Start > Control Panel > Network Connections.
Appendix C - Technical Specifications Technical Specifications Standards t *&&& O t *&&& H t *&&& B t *&&& t *&&& V t *&&& BC Security t 81" - Personal/Enterprise t 81" - Personal/Enterprise Wireless Signal Rates1 *&&& O ()[ )5 t .CQT r .CQT t .CQT r .CQT t .CQT r .CQT t .CQT r .CQT t .CQT r .CQT t .
Appendix D - Contacting Technical Support Contacting Technical Support U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. #FGPSF ZPV DPOUBDU UFDIOJDBM TVQQPSU QMFBTF IBWF UIF GPMMPXJOH SFBEZ t .
Appendix E - GNU General Public License GPL Code Statement This D-Link product includes software code developed by third parties, including software code subject to the GNU General Public License (“GPL”) or GNU Lesser General Public License (“LGPL”).
Appendix E - GNU General Public License Preamble The GNU General Public License is a free, copyleft license for software and other kinds of works. The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free software for all its users.
Appendix E - GNU General Public License TERMS AND CONDITIONS 0. Definitions. “This License” refers to version 3 of the GNU General Public License. “Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks. “The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
Appendix E - GNU General Public License The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form.
Appendix E - GNU General Public License 1SPUFDUJOH 6TFST -FHBM 3JHIUT 'SPN "OUJ $JSDVNWFOUJPO -BX No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures.
Appendix E - GNU General Public License A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation’s users beyond what the individual works permit.
Appendix E - GNU General Public License A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage.
Appendix E - GNU General Public License When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. "EEJUJPOBM QFSNJTTJPOT NBZ CF XSJUUFO UP SFRVJSF UIFJS PXO SFNPWBM JO DFSUBJO DBTFT XIFO ZPV NPEJGZ UIF XPSL :PV NBZ QMBDF BEEJUJPOBM permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
Appendix E - GNU General Public License 8. Termination. :PV NBZ OPU QSPQBHBUF PS NPEJGZ B DPWFSFE XPSL FYDFQU BT FYQSFTTMZ QSPWJEFE VOEFS UIJT -JDFOTF "OZ BUUFNQU PUIFSXJTF UP QSPQBHBUF PS NPEJGZ it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).
Appendix E - GNU General Public License :PV NBZ OPU JNQPTF BOZ GVSUIFS SFTUSJDUJPOT PO UIF FYFSDJTF PG UIF SJHIUT HSBOUFE PS BóSNFE VOEFS UIJT -JDFOTF 'PS FYBNQMF ZPV NBZ OPU JNQPTF a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it. 11.
Appendix E - GNU General Public License A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the nonFYFSDJTF PG POF PS NPSF PG UIF SJHIUT UIBU BSF TQFDJöDBMMZ HSBOUFE VOEFS UIJT -JDFOTF :PV NBZ OPU DPOWFZ B DPWFSFE XPSL JG ZPV BSF B QBSUZ UP BO arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of your activity of convey
Appendix E - GNU General Public License Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version. 15. Disclaimer of Warranty. 5)&3& *4 /0 8"33"/5: '03 5)& 130(3". 50 5)& &95&/5 1&3.*55&% #: "11-*$"#-& -"8 &9$&15 8)&/ 05)&38*4& 45"5&% */ 83*5*/( 5)& $01:3*()5 )0-%&34 "/% 03 05)&3 1"35*&4 1307*%& 5)& 130(3".
Appendix F - Warranty Warranty 4VCKFDU UP UIF UFSNT BOE DPOEJUJPOT TFU GPSUI IFSFJO % -JOL 4ZTUFNT *OD i% -JOLw QSPWJEFT UIJT -JNJUFE 8BSSBOUZ t 0OMZ UP UIF QFSTPO PS FOUJUZ UIBU PSJHJOBMMZ QVSDIBTFE UIF QSPEVDU GSPN % -JOL PS JUT BVUIPSJ[FE SFTFMMFS PS EJTUSJCVUPS BOE t 0OMZ GPS QSPEVDUT QVSDIBTFE BOE EFMJWFSFE XJUIJO UIF öGUZ TUBUFT PG UIF 6OJUFE 4UBUFT UIF %JTUSJDU PG $PMVNCJB 6 4 1PTTFTTJPOT or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Appendix F - Warranty Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation.
Appendix F - Warranty t "GUFS BO 3." OVNCFS JT JTTVFE UIF EFGFDUJWF QSPEVDU NVTU CF QBDLBHFE TFDVSFMZ JO UIF PSJHJOBM PS PUIFS TVJUBCMF TIJQQJOH QBDLBHF UP FOTVSF UIBU JU XJMM OPU CF EBNBHFE JO USBOTJU BOE UIF 3." OVNCFS NVTU CF QSPNJOFOUMZ NBSLFE PO UIF PVUTJEF PG UIF QBDLBHF Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship back any accessories.
Appendix F - Warranty t 5IF DVTUPNFS JT SFTQPOTJCMF GPS BMM JO CPVOE TIJQQJOH DIBSHFT UP % -JOL /P $BTI PO %FMJWFSZ i$0%w JT BMMPXFE 1SPEVDUT TFOU $0% XJMM be rejected by D-Link. Products shall be fully insured by the customer and shipped to D-Link Networks, Inc., 2525 Meadowvale Boulevard Mississauga, Ontario, L5N 5S2 Canada. D-Link will not be held responsible for any packages that are lost in transit to D-Link.
Appendix F - Warranty Limitation of Liability: 50 5)& ."9*.6. &95&/5 1&3.*55&% #: -"8 % -*/, *4 /05 -*"#-& 6/%&3 "/: $0/53"$5 /&(-*(&/$& 453*$5 -*"#*-*5: 03 05)&3 -&("- 03 &26*5"#-& 5)&03: '03 "/: -044 0' 64& 0' 5)& 130%6$5 */$0/7&/*&/$& 03 %"."(&4 0' "/: $)"3"$5&3 8)&5)&3 %*3&$5 41&$*"- */$*%&/5"- 03 $0/4&26&/5*"- */$-6%*/( #65 /05 -*.*5&% 50 %"."(&4 '03 -044 0' (00%8*-- -044 0' 3&7&/6& 03 130'*5 803, 45011"(& $0.165&3 '"*-63& 03 ."-'6/$5*0/ '"*-63& 0' 05)&3 &26*1.&/5 03 $0.165&3 130(3".
Appendix F - Warranty '$$ 4UBUFNFOU 5IJT FRVJQNFOU IBT CFFO UFTUFE BOE GPVOE UP DPNQMZ XJUI UIF MJNJUT GPS B $MBTT # EJHJUBM EFWJDF QVSTVBOU UP 1BSU PG UIF '$$ 3VMFT 5IFTF MJNJUT BSF EFTJHOFE UP QSPWJEF SFBTPOBCMF QSPUFDUJPO BHBJOTU IBSNGVM JOUFSGFSFODF JO B SFTJEFOUJBM JOTUBMMBUJPO 5IJT FRVJQNFOU HFOFSBUFT VTFT BOE DBO SBEJBUF SBEJP GSFRVFODZ FOFSHZ BOE JG OPU JOTUBMMFE BOE VTFE JO BDDPSEBODF XJUI UIF JOTUSVDUJPOT NBZ DBVTF IBSNGVM JOUFSGFSFODF UP SBEJP DPNNVOJDBUJPOT )PXFWFS UIFSF JT OP H
Appendix F - Warranty ICC Notice: 0QFSBUJPO JT TVCKFDU UP UIF GPMMPXJOH UXP DPOEJUJPOT 1) This device may not cause interference and 2) This device must accept any interference, including interference that may cause undesired operation of the device.
Appendix G - Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.